Freeman PFL618BR 3-in-1 Pneumatic Flooring Nailer

• Shoots three types of fasteners without changing magazine rail T-cleats L-cleats and staples
• Anodized aluminum and oil-less parts for extended wear
• Durable plastic carrying case
• Interchangeable floor plates for different thicknesses of flooring
• 7-year limited warranty

I am a flooring contractor and after using $480 flooring nailers for the past 7 years, I can say this is well worth it. My previous nailer bit the dust in the middle of a job and I rented one from "rip off Depot" and after spending $70 on a day and a half rental I figured I would order this one to at least get me past this flooring job and then cross my fingers for the next. I can honestly say that this is as good or better than both of my Bostich staple nailer and cleat nailer (each over $450!!!). Also, keep this in mind, all these nailers are made in China, none are made in the USA anymore. Bostich or aka Stanley used to make their nailers in the USA and it was worth the price but they have since fired all they american laborers and have not lowered their prices dispite the 1/4 cost of building the nailer since being built in China, now they are made in China for about 1/4 the cost and the rest is now in the wallets of CEO's of Stanley/Bostich so it really doesn't matter anymore( damn shame to). Stanley /Bostich is simply riding on their name. All the brands are pretty much the same now a-days unfortunetly. The 7 year warranty caught my eye and is key. This is definetly a no brainer. Here are a few obvious perks ...

Freeman Nailer ($190) 7 year warranty Bostich ($470 +) 7 year warranty

Freeman Nailer T, L & Staples ($190) Bostich Staples only! want L cleats? Spend another $470 ($960+)

Freeman Made in China Bostich Made in China

Freeman Decent durable plastic Carrying Case Bostich Cardboard Box & some used tape

Freeman Parts Aluminum Bostitch Parts "aircraft grade aluminum" i.e. ...um, Aluminum!

Freeman Rubber Mallet, Oil, wrenches Bostich Rubber Mallet

The bottom line is this: If this Freeman nailer gets me past 5 years of service then It did the job and I made an Excellent investment. If it gets me past 2 years than I still made out. Not to mention they also have a seven year warranty and I did call their support before hand and tell them I had a broken one and they said they would send me a new one with shipping sticker to send old one back ( I always do this with expensive tools), so they seem to be standing behind their warranty. Also, this nailer shoots three different type of nails! So save your $280 for something else nad buy the Freeman. Only thing they need to do now is make the damn thing in the USA then I would REALLY be impressed and give the 5 stars! Also, "Aircraft grade Aluminum" is like saying my tshirt is made of "aircraft grade cotton" ... there are 15 grade types of Aircraft aluminum and guess whateven Harbor Frieght tools are technically "aircraft grade Aluminum". Once again Bostich/Stanley is trying to screw with our heads, banking on hte name and robbing you blind.

Buy Freeman PFL618BR 3-in-1 Pneumatic Flooring Nailer Now

Invested about 1/3 the price of a name brand pneumatic flooring nailer and installed about 3500 square feet of hardwood flooring without a hitch. No miss fires, jams and worked to perfection. Light weight, easy to load and built solid. Would recommend with no problem

Read Best Reviews of Freeman PFL618BR 3-in-1 Pneumatic Flooring Nailer Here

Great price, beats renting that's why i got it obviously.

Did about 1,200sqf on the first job with a few jams (probably not oiling enough) but that wasn't a problem.

Very nice finish on the gun, handles great.

On the second job the piston or whatever is inside just wouldn't return the actuator and is audibly leaking air. I think i was just hitting this thing to hard and it couldn't take the abuse. Not sure what broke down. The website says 7 years limited warranty.

I would love a replacement but now i have to ship it to the company (not Amazon, which sucks) so not sure if it is worth the time and the fees involved. It already cost me time to drive around and rent a replacement, then drive to return it. Probably spent double already with all the stoppages.

If you are doing a small project (a room or two) then this is definitely your tool.

If another job comes about i will be probably considering something more heavy duty. Still undecided if I will go through with the repair process.

Reliability is more important then an eye catching price. That applies to all products, doesn't matter if it was made in China or say Ohio.

-update

Very, very, very good customer service. Got the tool replaced in 3 days no hassle whatsoever.

Want Freeman PFL618BR 3-in-1 Pneumatic Flooring Nailer Discount?

I purchased 900 sq. feet of hardwood flooring to replace some worn carpeting in our house and decided to try installing it myself. Since I was doing the job over several weeks, renting a flooring nailer at $30/day was not practical so I decided to purchase one. I purchased the Freeman based on the reviews, reasonable cost, warranty and availability of replacement parts. The gun arrived in a nice case with a sturdy hammer and an easy to understand manual. I never had a nail jam and the gun worked great but about halfway through the first room the driver blade failed to retract after firing a nail. This happened a few times despite making sure the tool was oiled before operation. It could sometimes be remedied by pulling back on the magazine spring, but I did have to remove the drive guide a couple of times to correct it.

I called Freeman's 800 number and spoke with a very helpful person who suggested I try a test involving my compressor and call back with the results. Unfortunately, the problem persisted. When I called back again I was told that they were very sorry I experienced problems with their product and they would replace the nailer and send me a return shipping label for the defective tool. I was expecting to get the label in the mail, return the defective tool and then get the replacement as that is how most companies operate. I was very surprised to have a brand new nailer arrive a few days later with the return shipping label enclosed. This is clearly a company that stands behind their products with outstanding customer service. The other reviewers of this nailer reported trouble free operation but problems can occur with any tool, even the most expensive. I can recommend buying any Freeman tool with confidence because of the 7 year warranty and a company that truly backs it up with great customer support. I gave the tool 5 starts despite the glitch because of my positive experience with customer service. I also purchased a Freeman PFN64 Finish Nailer for my project that has performed flawlessly.

Save 24% Off

I have been using Stanley Bostitch for years. I recently needed to purchase a new nailer and didn't want to purchase a tool that cost almost 600 dollars. I looked up the tools on Amazon and came across this Freeman nailer. I have used it professionally for several jobs and find that it is not only comparable to my old guns, but surpasses them in these categories: Price!!! How can you beat paying less than 1/3 the price of my old nailers. Quality!!! This tool is exactly what I get from my other nailers. The Freeman nailer works great and comes with its own carrying case that stores hammer, cleats, and nailer. This is just an added bonus. Keeps my nailer from being banger around at the end of jobs when it gets tossed in to the back of a truck.

Great tool.

JET JFR-12 1/2-Inch NPT Air Filter/Regulator

• Air filter removes solid particles and condensates moisture accompanying compressed air
• Air pressure can be maintained by the steeples regulator accurately over a wide range of flows as necessary for each application
• Easy to read indicator
• Full 1 year warranty

I purchased this regulator for a 60 gallon compressor with a 1/2" output. Overall this thing does everything a regulator and filter should do.

Pros:

Filtration on this unit is pretty darn good for the price. Much of the water/oil is captured by the filter. I haven't seen any evidence of any water/oil in the lines.

Line pressure gauge seems accurate as compared to the tank pressure gauge

The filter will automatically dump liquids when pressure is removed from the system.

I generally leave the system pressurized and haven't had any issue with air leakage.

Cons:

Attaching the pressure gauge to the regulator body is a bit of a pain. There is no clearance for a normal wrench between the gauge and the body so I had to tighten the gauge by torquing the gauge body. Perhaps this could be done during production?

For the price there is no doubt that this is a great purchase if you need a 1/2" regulator.

Buy JET JFR-12 1/2-Inch NPT Air Filter/Regulator Now

I purchased this regulator because of the 1/2 inch connection. I also selected this particular one because of the low price due to the fact it was listed as "used". The shipment was faster then I was quoted. The regulator was actually unused. The box was a little trashed which made me feel like someone bought it and then return it without using it. The only bad thing was the fact that no air pressure gauge came with it. I contacted the seller as soon as I opened it and they immediately apologized for the error and paid for a new one. The whole issue was very positive. I will definitely do business with them again and would recommend them to others with no hesitation.

Read Best Reviews of JET JFR-12 1/2-Inch NPT Air Filter/Regulator Here

This thing seems well made and in hindsigt I'm not sure I needed something so substantial. This definately is an improvement over the cheapo I had been using. I can't really say anything negative about this. It does exactly what I wanted it to do. It seems to filter out mousture quite well too. I like it. My employees like it.

Want JET JFR-12 1/2-Inch NPT Air Filter/Regulator Discount?

This is a very nice main filter/ regulator. Very solid with 1/2" in and out connections. The adjustment knob is precise and works as expected. The only thing to be careful about is that it is rated at 150 psi input pressure so if you have a bigger compressor (155 psi or more) you need to ratchet it down to 150 if you want to use this regulator.

Also I could not find a manufacturer's web site so I i assume it is a nameless chinese knockoff of some filter/ regulator costing x3.

But I think for the price you cant beat it.

Save 36% Off

I was reluctant of the combination of water and regulator but this thing holds up well and when put in line you lose the other bowl so it eliminates the possibility for leaks in the line up.

Bosch SN350-RH Rafter Hook

• Easily hang tool from rafters for increased productivity.
• Retractable Hook to move out of the way while not in use.
• Compatible with Bosch SN350-20F and SN350-34C framing nailers
• Includes: Rafter Hook and Allen Key

Any framing gun without a hook is worthless. It's too bad the Bosch 21 degree framer that I use this hook for didn't come with a hook but that's not the point. The hook is huge and works well although I've broken the pin that keeps the hook portion attached to bracket. Usability/Utility 10/10. Durability 6.5/10. The original hook that I purchased last about 18 months of medium to light use. It was easily fixed with a small Maze nail acting as a replacement pin. Regardless, I expect more.

Buy Bosch SN350-RH Rafter Hook Now

I own the Bosh SN350-20F, and even though I had to order this rafter hook extra it was well worth it.

Read Best Reviews of Bosch SN350-RH Rafter Hook Here

The item works as advertised and is really handy when working off the ground. The Bosch nailer should have made this a standard option on the tool. The hook works, but you have to push in on the spring loaded hook to move in between the open and closed setting and it is awkward. Bosch engineering should have worked on developing a smoother operating hook, other manufacturers have certainly have it mastered.

Want Bosch SN350-RH Rafter Hook Discount?

Rafter hook works great. I only gave it 4 stars because it can only be mounted on one side of the gun.

Rheem Ruud Condenser Fan Motor 51-23053-11

• Motor Type Permanent Split Capacitor
• Voltage 208-230
• Rotation Reversible CW/CCW
• Number of Speeds 1

Disappointed that this was advertised as RUUD OEM replacement motor but was a universal motor available anywhere. Problem is there is an extra wire that is not used on some units (mine) and the mounting bolts needed to be cut off for this installation. None of this is a big deal for an experienced technician but for a DIY guy is bothersome.

Milton 715BK M Style Quick Coupler: 1/4-Inch Female Coupler

• Hardened steel balls
• Stainless-steel springs
• Heat-treated and plated
• Made in the USA

This is the fitting you'll need on a 3/8" air hose with 1/4" NPT fittings. Milton M-Type coupler plugs are designed to fit this quick connect. This doesn't leak under pressure and requires no lubrication. Assuming you still have all the fingers on one hand, this is easy to operate; hold the ring back with your thumb and forefinger while gripping the hose with your other three fingers. Slip the plug in or out and let the ring go. A small burst of air is normal. This is another quality, made in USA product from Milton. They are the best.

Buy Milton 715BK M Style Quick Coupler: 1/4-Inch Female Coupler Now

MILTON BY FAR MAKES THE BEST COUPLERS OUT THERE. FIRST I FOUND THEM HARD TO FIND.SECONDLY THE PRICE IS THE SAME AS THOSE INFERIOR BRANDS..JUST USE ALITTLE TEFLON TAPE ON YOUR MALE END PLUGS AND YOUR READY TO GO.YOU'LL FIND YOUR COMPRESSOR DOESNT GO ON AS MUCH, SINCE YOU HAVE (NO MORE AIR LEAKS)...........

Read Best Reviews of Milton 715BK M Style Quick Coupler: 1/4-Inch Female Coupler Here

I did not realize that there really is a difference in quick connects.

I just upgraded to a 60 gallon Ingersol Rand compressor so I changed out a number of items that I was using with my old 20 gallon compressor. Initially (when I bought the 20 gallon comp) I had gone to my local Home Depot and picked up some of the fittings and couplers I would need. They served well until the upgrade. Reading some of the reviews for Milton I thought I would try their fittings and couplers. After they arrived I put a male connection onto one of my new spray guns and then connected the hose (with the Home Depot coupler). Didn't work! The old coupler wouldn't accept this Milton. Surprise, surprise!

So, since I had purchased an additional male and female coupler, I changed the old one out to the new. Worked fine as should be expected since they are now both Milton. Funny thing is, I still had a few air tools laying around with the older style (Home Depot) fittings attached and the Milton would accept them with no problem.

Now for the good part. . . .I looked down the barrel of the Milton fittings along side the HD fittings and the inside diameter of the Milton is larger than the Home Depot fittings! Another surprise. I just thought all fittings (3/8") would be the same. I now know better and the Milton is a MUCH BETTER choice.

Want Milton 715BK M Style Quick Coupler: 1/4-Inch Female Coupler Discount?

Good deal on these couplers. I shopped around and this was the best price for the quality.

The Milton connectors are premium connectors and much better than the cheap Chinese imports. These do not leak air so I can keep my compressor on all the time and not have it cycle on and off.