Campbell Hausfeld FP2028 1-Gallon Oil-Free Pancake Air Compressor with Accessory Kit

• User-friendly design
• Easy-to-read gauge
• 100 max PSI
• Tank eliminates the pulsations caused by piston action
• Accessory kit contains 25-foot recoil hose, female coupler, male plug, air chuck, inflation needle, 2-inch inflation nozzles

I bought this to use with surebonder's 9615 upholstery staple gun to reupholster a bunch of chairs. it works great. i'm rather impressed. it is really tiny, easy to use and i'm surprised that it makes no mess of any kind. i sit right on my dinning table to use it. it was loud but not as loud as some reviews made it out to be. the trick is to use it on a piece of carpet. it also is not nearly as loud in a normal room of your house as it is if used in an empty room that has a hard floors and no furniture such as garage or cement basement.

my only gripe was that it took me several days to figure out why i couldn't connect it to the staple gun. it does not come with a male quick connector that is needed to attach the hose to power tools. i bought this at home depot for under $2.

i read many reviews that complained of it not working. after using it this month i can kind of understand why. it's not the compressor. if you have not used one before i will give you the short list of resons it won't work that all happened to me until i got used to using a compressor.

there is a knob under it that lets it dry between uses. you must close it tightly before using it.

you need to really, really tighten the hose onto the compressor before use.

if you over oil your air tools or always leave them connected, the oil will seep into the male connector at end of hose and trap condensation. if this happens, you will need to wipe out the connector with a paper towel until it feels dry again.

at the end of long work days you'll want to let it dry out. you should take the hose off and hang it so both ends hang down and open the drain knob underneath. I have found it to work super efficiently since i started to do this. now i don't need to keep running it to keep at 60 80 psi. although i do have to turn it on ever 10 or 20 minutes for about 30 seconds to keep the psi.

Buy Campbell Hausfeld FP2028 1-Gallon Oil-Free Pancake Air Compressor with Accessory Kit Now

I bought this compressor because I wanted a small tank-based compressor for my garage for keeping my car and bike tires filled and for filling basketballs and soccer balls.

I have had it for about a month now and it works great for what I bought it for.

The good:

1. Its small and light, easy to pick up and move around. Does not take up much space in my work area. It has plenty of power for filling tires and basketballs.

2. Great price.

3. Easy to use.

The bad:

1. Noisy. I read other reviews that said it was loud, but in use, it is louder than I expected. With the small tank, the motor ends up runninng most of the time I am using it. I find I have to wear ear protection when I am using it, even when I am outside in the driveway.

2. Light weight. Being light weight is nice when I want to pick it up and carry it around the house and garage, but it has its downside. It came with a 25 foot coiled air hose and when you get the cord extended out 8-10 feet, it tips the compressor over on its side.

That's the good and the bad. Works great for what I need it for. I don't need a compressor for air tools, so I did not want to get a bigger compressor because it takes up too much room around my workbench. I used to use a small electric compressor without a tank, but it took too long to fill up car tires. This Campbell Hausfeld works perfect for what I need. I would buy it again.

Read Best Reviews of Campbell Hausfeld FP2028 1-Gallon Oil-Free Pancake Air Compressor with Accessory Kit Here

This air compressor does not hold a lot of air one gallon to be exact. However, it fills to its maximum 100 psi relatively quickly and once there, will add about 6 or 7 psi to my each of my car tires. This is plenty to air up a tire and by the time I go to the next tire and check it's pressure, the compressor is back to 100 psi and ready to go. For me and my needs, which are not commercial or professional, this thing does the trick for the right price.

Want Campbell Hausfeld FP2028 1-Gallon Oil-Free Pancake Air Compressor with Accessory Kit Discount?

My wife bought this for me for Christmas a year and a half ago. I used it to inflate car tires a few times a year. A few months ago the pressure would not build past 42lbs. After some troubleshooting I replaced the safety valve for about 24.00 (Sears Parts Store). Still would not build. I ended up taking apart the piston assembly, it looked fine no burnt or scratched valve no bad piston ring. Re-assembled and it was fixed! 100lbs psi again. Two days later down to 25lbs. This thing is loud and after taking this apart I can see why its cheap. The only replacement for the piston I can find is the whole motor/piston assembly which is probably more than a new compressor. Look elsewhere for a better quality unit.

Save 58% Off

I bought this air compressor to use for airbrushing. I need 20-40 psi and less than 1 cfm. This compressor will generate 100 psi. Here is the funny part... the instruction sheet says for break-in you should turn the regulator valve clockwise all the way and leave it open (no hose, etc) and run for 5 minutes before using. Fair enough. No regulator... no valve... the think runs 100 psi and just splills that out into what ever you hook up to it. You would have to add a regulator to it. The other joke... it was so incredibly loud it was louder than my 6 HP 60 gallon upright compressor in my garage!!! Ran it in my basement with the doors and windows shut and my wife was concerned the neigbors Easter dinner would be unejoyable in their homes in the neibhorhood around the house. The noise was incredible... I would say equivalent to a Jet air craft taking off in close proximity in terms of decibles. I have been exposed to two of Campbell Hausfeld's compressors... both were the worst pieces of engineering garbage I have ever seen. No reflection on Amazon please.

Goodyear i5000 Cordless Tire Inflator and 12-Volt Power Pack

• High pressure 12 Volt portable inflator
• Inflates 14 inch vehicle tire from 0-28lbs of pressure in under 4 minutes
• Inflator operates in 2 different modes: Battery or Directly off vehicle current
• Charges off of AC household current or off 12 Volt vehicle Current, both power adaptors are included
• Built In 12 Volt power outlet to operate cellular telephones, invertors or other 12 Volt equipment

Received the pump when promissed, so far it has worked as advertised. I really like the auto shut off when the tire pressure reaches your selected pressure. Some advice, if you set the pressure for 32 pounds of pressure and the tire pressure is already at 32 psi or HIGHER the pump will not start, it only starts when the tire pressure is BELOW what you set psi for. I have already used it for the kids soccor balls, my vehicle tires (Ford F150) and my travel trailer tires, with air pumps that need to be plugged in the a power source, this would not work on my travel trailer because the standard 10 foot power cord would be too short for me to reach the trailer tires!. It also came in handy when having to winterize my travel trailer by pressurizing the water lines to blow out the water from the lines. Also, a great price for the convenience of not needing to plug it in to an outlet or cigarette lighter!

Buy Goodyear i5000 Cordless Tire Inflator and 12-Volt Power Pack Now

Very good machine, works like a champ. Wish it would tell me when it's full, rather than NOT starting on a tire that is already at full charge. It took me a while to realize this "feature". Great to be wireless!

Read Best Reviews of Goodyear i5000 Cordless Tire Inflator and 12-Volt Power Pack Here

I bought this for my husband as a gift. We have a camper and he wanted something that we could take with us when we travel that doesn't need electricity. The first one we received did not work (worked for about 3 minutes, then quit), but they quickly sent me a replacement and it works great! His father also has this pump, has had it for several years and is quite happy with it!

Want Goodyear i5000 Cordless Tire Inflator and 12-Volt Power Pack Discount?

Be aware that you must cool the unit for 10 minutes after running it for 10 minutes so it doesn't burn out. I added about 4 psi to my vehicle tires and it ran for less than a minute per tire. It runs quiet for an inflator. The built-in lighted dial guage is very accurate, but kind of hard to read because the marks are small and close together.

Setting the target pressure is easy, you just twist the guage until a pointer lines up with the psi you want. The inflator automatically shuts off at that pressure and it is accurate and consistent. No switching back and forth between filling and checking with a separate tire guage and bleeding air to hit the target pressure. The setting stays until you move it again, so you can bring all your tires to the same pressure without re-setting it for each tire. No fuss like with a digital one. Super convenient.

I recommend charging the battery immediately after use and keeping it fully charged at all times. The lead acid battery will have the longest lifetime that way. Once the battery gives out, the only way to run it is directly powered from a 12V vehicle outlet.

The manual and the labelling of switches and sockets is a little confusing, but operation is not overly complicated. There are two switches and two power ports. You'll figure it out.

You could burn it out with a big job like completely filling an RV tire, raft, air tank, etc. unless you stop every 10 minutes. As long as you stay within the limits, this will be a good tool. Probably the most convenient way to maintain vehicle tire pressures.

Works great. This item has a way of pre-selecting the amount of tire pressure and you let it run until the tire is properly inflated. Good buy.

Porter-Cable FC350A Clipped Head 2-Inch to 3-1/2-Inch Framing Nailer

• Uses 30 degree to 34 degree 2-inch to 3-1/2-inch by .113-inch to .131-inch paper collated clipped-head framing nails
• Power to drive nails (up to 3-1/2-inch by .131-inch) into engineered lumber
• Compact body design for better balance and style
• Consistent power on every shot with internal piston catch mechanism
• Selectable trigger - restrictive or contact actuation mode;Tool-free depth-of-drive adjustment with detents for proper setting of nail heads

This new nailer (the FC350A) is one great tool. Very powerful, a good range of nail sizes, not too heavy, works well even in the lower psi range. Well made, simple to maintain. I chose the clipped head over the full round head because the magazine doesn't stick out quite so far. Which leads me to the caveat. If you search for nails for this gun, you'll see many manufacturers stating compatibility. Also, you'll see sites quoting the gun works with nails strips from 30 to 34 degrees. This is not so! You *must* have nails strips of 34 degrees, except for the shortest length nails. Why? If you go to Home Depot and purchase a box of 3 inch nails, clipped head paper collated, like those from Grip-Rite (who state compatibility with the FC350) you'll notice they are 33 degrees instead of 34. This one degree difference means that longer nails don't get punched by the nailer the impact head just slides down the nail. Shorter 33deg nails sometimes work because their short length means the head is more in line with the impact head. So really the problem is in trying to obtain 34 degree paper collated nail strips. I've tried everywhere, including all the merchants listed on the PorterCable website. I finally ordered online from www.circlesaw.com who have the right range. It's a great tool, it's just a pain in the $%#$% to get the right nails, at least right now. Maybe it's still early days.

Buy Porter-Cable FC350A Clipped Head 2-Inch to 3-1/2-Inch Framing Nailer Now

I'm not sure why someone experienced problems with the 33 degree nails from grip-rite at Home Depot. I bought the FC350A nailer from Amazon and bought a box of 3 1/4 inch x .131 hot dipped galvanized nails from Home Depot. The nailer and the nails work great for me! I really love the size of this nailer. Very nice improvement over the older version. The price from Amazon is also very competitive. I am extremely pleased!!!!

Update After running several hundred Nails through this nailer, I stand by my earlier conclusions. I have not had any problems with the Grip-Rite nails from Home Depot. I plan to try the Paslode 30 degree nails in this nailer. Great Nailer!!!

I built many projects with this nailer including a pool fence, framed decks, framed buildings and framed my basement. I stand by my earier comments. This nailer is superb and the Home Depot nails work fine!

Read Best Reviews of Porter-Cable FC350A Clipped Head 2-Inch to 3-1/2-Inch Framing Nailer Here

I bought one of these guns back in the beginning of 2004. I have 4 now. It's very well balanced. It drives 3 1/4 nails in lam beams with ease. As long as the preasure is right on the compressor. I like the switch on the trigger for the sequential or bump fire. And then the depth knob on the nose is handy too. I sold off my two Dewalts, two Sencos, and Craftsman framers because I never used them after I got this one. It loads like a Senco from the bottom of slide. Makes for a quick reload. Mine all have cases too which is nice. The only framer I have beside these guns is my Paslode. This gun is the right size with short magazine gets into tight spots. I have only had one problem with one them the drive broke but it was under warranty. If you want a gun that will please and take a beating at good price get this one.

Want Porter-Cable FC350A Clipped Head 2-Inch to 3-1/2-Inch Framing Nailer Discount?

I'm a computer nerd with an air compressor & pnumatic power tools. The only thing more dangerous is a father with a camcorder. I know this because I have all the above. I bought this clipped head nailer to finish off the basement, to build an office for myself to give the family more room upstairs. This thing works GREAT! This is so awesome. I put up a new wall in NO TIME, then I started looking for more projects. Standard building code puts studs 16" apart, such restraints are unnecessary when you wield such power as this. Be careful as you may find yourself nailing studs perpindicular just to keep the adrenaline flowing, or worse, tearing out old sheetrock walls to see if they "have enough support". You'll start looking for projects once you have this. I bought this because it was cheaper to buy a $100 air compressor and this $200 gun than pay someone $500 in labor to put a wall up for me [Insert Tim the tool-time Taylor grunt here]. My wife fears that we're going to be living in the next Winchester Mansion and has forbidden me from buying any more nails. No worries though, I'm not even half way through the first box of 2,500. Muhahahahaha!

Save 56% Off

Bought this gun to reframe a old gargage. Couldn't ask for any thing better. The best feature is the selectible trigger, when nailing location really matters. Never had a jam or unsunken nail.

Interstate Pneumatics W1160T 3/8 Inch Standard W/"T" Handle Regulator 0-120 PSI

• Port Size: 3/8"
• Body Material: Die Cast Metal Body
• Max Inlet Pressure: 300 PSI
• Delivery Pressure: 0-125 PSI
• Flow @ 100 PSI: 110 SCFM

Works well, much better than a plastic type that I replaced. Simple, not too expensive, good value for the money. Seems to hold the set pressure well. Overall, a good buy for the money, especially compared to what else is available.