Ingersoll-Rand 2131-TK2 1/2-Inch Impact Wrench Tune-Up Kit

• 1/2" Impact Wrench Hammer and Anvil Kit for use with 2131A

My 16-17 year old 2131 lost its powerit couldn't remove lugnuts. I was set to buy a new gun but figured I'd try to rebuild it. Installed the rebuild parts and the gun is almost like new! Notethe vanes I received were a different shape than the originals. The originals were symmetrical if laid out flat, but the new ones had a small cut out on the bottom on one side. I put the cut out towards the back of the gun and it works great. The picture that comes with the kit shows the old vanes.

Buy Ingersoll-Rand 2131-TK2 1/2-Inch Impact Wrench Tune-Up Kit Now

Ive been a mechanic for about 10 years. When I first started I purchased an Ingersoll Rand 2131. Finally it started getting weak and would give me problems once in a while. Figured I would try to rebuild it instead of buying a new one. This kit is awesome. Comes with every little seal and gasket and all the vanes. Gun works like it is brand new!

Read Best Reviews of Ingersoll-Rand 2131-TK2 1/2-Inch Impact Wrench Tune-Up Kit Here

This is an original equipment kit and thus all the parts are exactly right. My only complaint is that the instructions are not great for first-time impact wrench repairers like myself, but I was able to figure it out.

Now my wrench has the same oomph it did when I first bought it ten years ago. Yeah!

Want Ingersoll-Rand 2131-TK2 1/2-Inch Impact Wrench Tune-Up Kit Discount?

It turned my old tool that stopped working into a brand new impact again. I love it. Buy this if you're having problems

Save 53% Off

My "Thunder Gun" Ingeroll Rand 2131 had given years of flawless service. Then, all of a sudden , when air pressure was attached, the gun would NOT stop running. Strange problem. This Tune up Kit repaired my Air Impact to like new condition. It was a snap to install also.

Porter-Cable C2002 Oil-Free UMC Pancake Compressor

• 150 psi max tank pressure stores more air in the tank for longer tool run times
• 2.6 SCFM at 90 psi allows for quick compressor recovery time, per ISO1217
• Six-gallon pancake-style tank for stability, includes water drain valve and rubber feet
• Low-amp 120-volt motor starts easily in cold weather or with extension cord
• Durable oil-free pump for long life and no maintenance

I purchased this item from Lowes just because I had seen this item manufactured on How It's Made on the Science Channel and took note that many steps were taken during manufacturing to insure a good end product. I have other compressors at my home including a 60 Gallon 240 Volt professional grade compressor but this portable compressor is a great product. It is compact, light, powerful, is stable and balanced when running, and has a cutoff pressure of 150 P.S.I. that helps it stay well ahead of the performance game. I use it whenever I want a portable air source, it is as convenient to transport as a portable vacuum cleaner. I would recommend this to any homeowner who needs a reliable, convenient source of compressed air. Additionally, it has two output quick connectors and very nice gauges and regulator. It is my first oil-less air compressor and I am satisfied with it's performance.

Buy Porter-Cable C2002 Oil-Free UMC Pancake Compressor Now

I recently purchased this for my father, we work on a cabin in Canada, using a generator, and we wanted lightweight as we haul items in and out by boat. Also, the generator is not that large (3000 watt) and it handled this compressor without any problem. I previously purchased an oil-lubed compressor for myself (PC, 2.5 hp, dual tank, model CPLDC2540S), because I wanted something quite. I was surprised when I turned this compressor on, as it seems quieter than mine!! It also weighs less than mine!

There is 1 minute of assembly requiring a phillips screwdriver, but it was fairly easy (attach the motor to the tank, although the hose is already attached).

I think it is a good buy from of a good brand.

Read Best Reviews of Porter-Cable C2002 Oil-Free UMC Pancake Compressor Here

Ordered this compressor for odd-jobs and basic 'inflation' duty around the house. Car tires, bike tires, and air mattresses... Very handy to have around. Unit is VERY light, much more easy to transport than I was expecting. Loud compared to my old 20gallon oiled compressor unit, but not unbearable.

Takes about 2 minutes from empty to full pressure cutoff. Very happy with the quality of the construction, clean looking unit and the 2 air outlets are a definite plus.

No hose is included with this kit, contrary to the attached picture. Better off going with the base kit and getting nicer accessory items than buying the full kit and paying a premium for 25ft of hose and a few cheap bits.

EDITED MARCH 28, 2011:

I broke the compressor in according to the information I read online (Run 15mins with the drain valve open to prevent pressure build up). So far it's still working fine for me.

One of my BIGGEST complaints, and the reason I've dropped a star off the review is the fact that the Hose Connections (2 of them, which is nice feature at this price) are attached directly to the gauge panel. The unfortunate part about this is that if the hose gets pulled, the whole gauge panel will rotate on the threaded air output from the tank. So far, it's happened to me about 3-4 times and it hasn't caused a problem-but I'd really have to reconsider this for a medium duty environment. It's only a matter of time before it begins to leak.

2nd-The compressor, for it's size, is just too LOUD. It's so loud and vibrates so much, that on any smooth surface (Concrete, Wood Floor) it'll actually vibrate the whole unit in a circular motion. Not a huge deal if you're not working in a tight space, but it's annoying to continually have to monitor the compressors position in my shop and pull it away from the wall. It does have thick rubber feat, but they just can't compensate.

I can't recommend it as whole-heartedly as I did before. For 150 dollars, I'd recommend saving a few more dollars and putting it toward a better quality/capacity unit.

Want Porter-Cable C2002 Oil-Free UMC Pancake Compressor Discount?

I have owned this compressor for over a year, used it on 3 or 4 finish nailer projects around my house. Started leaking air bad. Ordered the replacement parts (tube and a "gasket") and I can see why it leaked. Once I disassembled it I could see that the parts were cheaply made both the originals as well as the replacement parts. Rather than fix it, and probably have the same thing happen very soon I opted to junk it and purchase a portable Ingersoll Rand compressor. Talk about night and day!!

I own quite a few tools, including another Craftsman compressor. Craftsman gets a bad rap sometimes, and sometimes it is deserved, but I've had my Craftsman compressor for years. It's a big one, not portable though which is why I replaced this piece of junk PC Compressor with an Ingersoll Rand model.

I would advise anyone / everyone not to buy this compressor. It was the first Porter Cable tool I purchased, and based on the quality I will not be buying any more products from this company. I had thought about a couple different woodworking products that are made by Porter Cable, but no longer even considering it!!

Save 53% Off

This is my first review. I never seem to have time to write them, though I always read (and appreciate) the reviews that others have taken the time to write. My turn. So I am a professional residential remodeler. As you might imagine, I possess quite a stable of tools. And if not for one MAJOR flaw, I would continue to use and recommend this compressor. It clearly is not designed for significant framing activity. But its size and oil-less feature, make it ideal for trim work and small framing projects, EXCEPT for the fact that the drain valve on the bottom of the tank fails over and over again.

I bought my first unit some 3 years back used it happily, if irregularly for over a year. Then the valve failed. I assumed it was a one-off thing and, given the reasonable price, bought another one. This time I got it at Home Depot since I needed one immediately. I used that for some many months (6-9?) and the valve failed again. I returned it and bought another one. Some 4-6 months later, it happened AGAIN. It always seems to happen in the middle of a project and I need to quickly go replace it. With a receipt, I haven't had an issue replacing it since I don't want to just throw it away and lose out on my "investment".

But darn if my FOURTH PC pancake compressor didn't just fail in the exact same manner just last week. That makes FOUR of these units that have all failed in the exact same way. I can't believe PC doesn't know about, and hasn't rectified this problem. It surely can't just be my bad luck. For someone who occasionally uses this compressor, maybe it will last for years before the valve fails. But it clearly can't handle any reasonably regular usage. And I should add that I always drain my tank after each usage. I don't let the air, remain in the tank and condense and rust the tank so it isn't a maintenance issue.

I wish this valve wasn't made so poorly because it renders the whole unit useless it can't be site remedied with any ease or efficacy. I would otherwise have enjoyed keeping this tool in my arsenal. I guess I need to look elsewhere for my portable, oil-less compressor needs....

So

Hitachi 23 NP35A Gauge Micro Pin Nailer

• Large fastener capacity for fewer reloads and less downtime
• Dual trigger for safe and accurate placement of fasteners
• Rear exhaust directs oil and debris away from the work surface
• Reload Indicator for easy visual recognition of low nail quantities to avoid dry firing
• Depth adjustment for flush drives into a variety of surfaces
• Comes with a 5-year limited warranty

I usually don't write reviews of a tool until I've used it quite a bit, but I'm going to make an exception in this case because there is only one other review. I would like to thank Jim, the first reviewer, as his comments inspired me to take the plunge and try this product.

This Hitachi NP35A is my first micro pinner, although I do own and use a few larger pneumatic tools (15 gauge nailer, 18 gauge nailer, 2 staplers). I typically prefer to use screws rather than nails, but there are occasions when the unique attributes of a power driver nail outweighs it's many disadvantages.

Here are my first impressions of the Hitachi NP35A 23 Gauge Nailer.

Pros:

o compact, lightweight, and comfortable to hold.

o high quality product, for example magazine slides in and out with smooth precision.

o trigger is comfortable, double trigger is relatively easy to get used to.

o the soft nose tip leaves no mark whatsoever on even soft woods.

o very quiet, pleasant to use (no hearing protection needed with this little guy).

o easy side loading of pins, and automatically adjusts to different pin sizes.

o using the soft tip, appropriate air pressure, and good technique, pins are driven to a perfect depth just below the surface (the depth is adjustable via the use of a hex wrench on the nose piece).

o surprising nice blow molded plastic case.

o an easy to see bright orange "low pin indicator" (of course, it doesn't work if one is not paying attention and doesn't look at it ... just one of my many faults I'm afraid....)

o although the minimum specified pin length is 5/8", I was able to use the 3/8" pins without a problem (this is quite a good thing, for my projects).

o made in Taiwan (often a significant step up in quality compared to China made goods).

Cons:

o the manual has a few typos (e.g. "all crews must be tightened..."), and it is bloated with the usual tedious and uninformative safety stuff (dictated by lawyers, presumably), but really, you can probably see that I'm nit-picking here.

Notes:

I have tested this product primarily with Western Fir (actually harder than many "hard woods"), and a sample piece of 100 year old clear white oak (recovered from a badly broken desk). As long as one presses the tip firmly to the wood all pins are driven flush, although one does have to crank up the air pressure a bit for longer pins and harder wood.

I used Grex 23 gauge pins (since they come in a convenient multi-size package, available here on amazon for about ten dollars).

The longest pin length I tried was 1". This gun is specified to be able to handle 1-3/8, and I do not doubt that it will, but for now I can't see myself needing or wanting to drive these incredibly tiny, thin little needles into anything that would require longer lengths. However I know that many people do use much longer pins. Perhaps as I become more comfortable and experienced with this tool I too will join the super-sized crowd.

As you probably know, these pins are much smaller than 18 gauge brads, and much less noticeable. However, they are not invisible, especially in lighter woods. Nonetheless, they are much less visually distracting than their 18 gauge cousins. Also, if you build small things (say drawer inserts using 3/16" thick dividers) an 18 gauge brad is simply too big it would split the wood whereas a 23 gauge pin works very nicely (along with a bit of glue).

Hope this information is helpful to you.

Buy Hitachi 23 NP35A Gauge Micro Pin Nailer Now

Had purchased a pin nailer from HF about 7 months ago and now finishing up a trim job on kitchen cabinets it decided to quit accepting 1 inch pin nails. Ran a search on Amazon and found this one. I have 2 other Hitachi nailers, so I ordered this for overnite delivery (Amazon Prime). Used it today and absolutely no problems. Its light, accurate and the nose pad protects the work piece. You do have to adjust the depth when using the nose pad. Adjustment is quick and easy. Hitachi makes some questionable quality items, but I have found their nail guns to be of a high caliber. If you need a high quality pin nailer, this is it.

11/4/2010

UPDATE:I guess I spoke too soon !! All of a sudden it started to jam. Tried various manufacturers pin nails and they all jam frequently. A real shame!! Gonna have to return it.

Read Best Reviews of Hitachi 23 NP35A Gauge Micro Pin Nailer Here

I bought this gun when my 5 year old Porter Cable gun gave up. What this gun does that the PC didn't is shoot 1 3/8" nails and set them below the surface in hardwoods. The PC was/is a good gun, but I feel this gun is better. It shoots bigger nails and costs less. As long as I get at the least the same amount of use from it as my PC, I'll be a happy woodworker.

Want Hitachi 23 NP35A Gauge Micro Pin Nailer Discount?

This little gun is awesome to use. It is well designed, fits in your hand well, is quiet and comes with tool oil, glasses, and 2 tips!! This gun is very easy to use. I have no complaints with it. I have other Hitachi tools and find their quality to be top notch. It is amazing that nails this skinny could be used without the nails bending, but it works without failure. The nails are so small that the holes are unnoticeable, and the 2 included tips are awesome. I can't imagine using a gun like this on your fine projects without using a tip. Others are more expensive, but this little wonder does the trick. Buy this gun, you will be very impressed and satisfied, like me.

Save 50% Off

I was so glad to get my micro pin nailer in the mail. It did let me down however. This nailer would consistently drive the nail too shallow despite trying to adjust the depth. I had to take off several moldings and trim pieces due to the remaining nails sticking out about 1/4 of an inch. I do not think this device was made to drive nails in that are greater than 1 inch despite what the manufacturers details may tell you. The product is made to drive fasteners up to 1 and 3/8" but in my experience this was not the case. I will return the product and save my money for the Grex micro pinner.

Hitachi EC12 14.5 amp 2-Horsepower 4-Gallon Oiled Twin Hot Dog Compressor

• 14-1/2 amp 2-horsepower 4-gallon oiled twin hot dog compressor with carrying handle
• 4.1 cfm delivered at 90 psi; shut-off valve at line and auto reset
• Cylinder constructed of cast iron
• Includes DEWALT synthetic compressor oil and pressure regulator
• 60-pounds; 1-year warranty
• At 60-pounds, the EC12 is easy to carry to any jobsite
• Cast iron, oil lubricated pump
• Comes with a 1-year limited warranty
• Contractor preferred 4-gallon twin stack tank
• Heavy-duty 14.5-Amp induction motor for extended use

This machine is yet another good example of high quality Hitachi engineering. This compressor has outlasted several other brands. The machine has run two finishing guns continuously for almost a year and hasn't needed anything more than an oil change The regulator is predictable, and adjusts as easily as other brands. I firmly believe that Hitachi gets 4.1 CFM out of 14.5 amps. We simply do not run out of air no matter how fast we are working with the Senco SFN40's. Down time has been zilch. One thing we did add was a water/oil separator and filter to protect our work and our guns. I suppose Hitachi (and most other brands) leaves these off so that they will have a competitive price. But it does not make economical sense for YOU to leave them off.

While I have given this compressor a 5 star rating, there are some things for the engineers (and you!) to think about in the next model: 1. The way the regulator is mounted it is difficult to make a manifold for two hoses without hanging those pipes out there where they can get knocked off. Anyone who has knocked one off before will know that A) everyone in the neighborhood knows it right away and B) it puts you down for some expensive time. And C) when this happens, it often creates an unwanted projectile. It took me three street elbows and an hour of figuring to get the quick disconnects in a safe place. 2. When you pick the unit up with the handle, the unit tilts a bit. This means you have to hold it out away from your body a bit more than the size of the compressor would promise. All that horsepower weighs enough to make this more uncomfortable than need be. We just bent the handle with a torch to get on the center of gravity.

These are relatively small gigs on a really great compressor. I only spent so many words on them so that the engineers might just read this. It seems they will have plenty of time to correct this before the ones I own wear.

Buy Hitachi EC12 14.5 amp 2-Horsepower 4-Gallon Oiled Twin Hot Dog Compressor Now

The hitachi 2 horse protable compressor is light enough tocarry around the jobsite but heavy enough so it won't fall out theback of the truck. It delivers plenty of air for nailers air wrenchs and filling tires. I wouldn't use it for painting but it was about the same price as the Coleman compressors.

Read Best Reviews of Hitachi EC12 14.5 amp 2-Horsepower 4-Gallon Oiled Twin Hot Dog Compressor Here

I chose the Hitachi three years ago because it has a fine compressor and motor, solid construction, and overall good design. It has been entirely reliable and three years later I still am using it both in my cabinet shop and on the job for residential remodeling. The only significant design flaw is the position of the gauges. They are subject to being knocked off. I found this out the hard way one day when I had to slam on the brakes in my van and a sliding tool box sheared one of them off. Despite this one flaw I would still by another Hitachi in a heart beat. The Hitachi is not only reliable, but, unlike many compressors, it truly works on 15 amps. This compressor has never blown a fuse on me, which is something of a miracle considering the wiring in many of the older homes I remodel.

Want Hitachi EC12 14.5 amp 2-Horsepower 4-Gallon Oiled Twin Hot Dog Compressor Discount?

first the reasons why i only gave it 4 stars. The handle is just a little too far forward which i always notice and makes it awkward to carry/move sometimes. The other item is the brass stem out of the upper tank to the regulator; it positions the regulator in a location which is very susceptible to be knocked off. The positives: I've used it for over a year now, building two houses (both framing and finish guns), with little or no maintenance, the oil lubed compressor is fast.

Save 47% Off

I have had this unit for several weeks now, and have had my expectations exceeded. The unit has no difficulty running on a 15 amp circuit in my house with older wiring (I was expecting many trips to the breaker box I have yet to trip one.)

The regulator stem is in an exposed position where it could be damaged/broken off if struck hard enough or handled carelessly, and the unit is every bit as loud as I expected (invest in some good earplugs) but still, I am extremely pleased my decision to go with this unit.

This becomes the third Hitachi tool product I have purchased, and the quality of their products continues to impress me.

Powermate PL1581109 11-Gallon Invector Vertical Air Compressor

• Oil free, low maintenance operation
• Circuit breaker friendly motor
• Compact shroud design with fully integrated regulator, gauges, air outlet, large on/off switch, tool holders and tool tray
• Compact 11-Gallon vertical portable tank saves space yet remains portable
• Maximum pressure: 125 PSI; CFM at 90 PSI: 4.0; CFM at 40 PSI: 6.0; RHP: 1.5; UL and CSA certified

This is a very nice Air compressor for a small garage, I have used it so far to work on motorcycles and will be using it to sand and paint my pickup. It is a nice machine a little louder than I had hoped but livable.

Buy Powermate PL1581109 11-Gallon Invector Vertical Air Compressor Now

I was looking for a replacement compressor that would last longer than my last. This was not the case with this

cheap compressor!! As soon as I pulled it out of the box, I was so excited til I plugged it in. It did not work.

I thought maybe a breaker was thrown. Nope. I tried every outlet in my house and still nada. Do not buy it is a POS!!!!