Ingersoll-Rand 2131-TK2 1/2-Inch Impact Wrench Tune-Up Kit

• 1/2" Impact Wrench Hammer and Anvil Kit for use with 2131A

My 16-17 year old 2131 lost its powerit couldn't remove lugnuts. I was set to buy a new gun but figured I'd try to rebuild it. Installed the rebuild parts and the gun is almost like new! Notethe vanes I received were a different shape than the originals. The originals were symmetrical if laid out flat, but the new ones had a small cut out on the bottom on one side. I put the cut out towards the back of the gun and it works great. The picture that comes with the kit shows the old vanes.

Buy Ingersoll-Rand 2131-TK2 1/2-Inch Impact Wrench Tune-Up Kit Now

Ive been a mechanic for about 10 years. When I first started I purchased an Ingersoll Rand 2131. Finally it started getting weak and would give me problems once in a while. Figured I would try to rebuild it instead of buying a new one. This kit is awesome. Comes with every little seal and gasket and all the vanes. Gun works like it is brand new!

Read Best Reviews of Ingersoll-Rand 2131-TK2 1/2-Inch Impact Wrench Tune-Up Kit Here

This is an original equipment kit and thus all the parts are exactly right. My only complaint is that the instructions are not great for first-time impact wrench repairers like myself, but I was able to figure it out.

Now my wrench has the same oomph it did when I first bought it ten years ago. Yeah!

Want Ingersoll-Rand 2131-TK2 1/2-Inch Impact Wrench Tune-Up Kit Discount?

It turned my old tool that stopped working into a brand new impact again. I love it. Buy this if you're having problems

Save 53% Off

My "Thunder Gun" Ingeroll Rand 2131 had given years of flawless service. Then, all of a sudden , when air pressure was attached, the gun would NOT stop running. Strange problem. This Tune up Kit repaired my Air Impact to like new condition. It was a snap to install also.

Amflo 25-24-RET Blue 300 PSI PVC Lead-in Air Hose 1/4" x 24" With 1/4" MNPT x 1/4&#03

• Absorbs the vibrations and pulsations from air compressors and air impact tools
• Providing longer life for the balance of the pneumatic system
• 300 PSI Blue PVC lead-in air hose
• Hose diameter is 1/4 inch and hose length is 24 inch
• 1/4 inch MNPT x 1/4 inch FNPT fittings with ball swivel

An affordable air hose do the job right.Seems a little cheapo but works well.haven't use a lot but not issues at this time

Buy Amflo 25-24-RET Blue 300 PSI PVC Lead-in Air Hose 1/4" x 24" With 1/4" MNPT x 1/4 Now

I hope this company make 4 feet or 5 feet length hose with same fittings. This way, the connection area( air feed side ) won't scratch cars bumper area. Overall, this is good quality hose for my mini air ratchet.

Porter-Cable C2002-WK Oil-Free UMC Pancake Compressor with 13-Piece Accessory Kit

• 150 psi max tank pressure stores more air in the tank for longer tool run times
• 2.6 SCFM at 90 psi allows for quick compressor recovery time, per ISO1217
• Air coupler and plug are factory installed on the air hose to save user labor and to prevent leaks
• 6-gallon pancake-style tank for stability includes water drain valve and rubber feet
• Low-amp 120-volt motor starts easily in cold weather or with an extension cord
• Equipped with a durable oil-free pump for long life and no maintenance
• Shroud, handle, and console cover protect vital components and make unit easier to carry

After reading TONS of reviews on various air compressors, I knew I'd buy the Porter-Cable version. I'm a homeowner and am NOT an expert in power tools. But I do enjoy home improvement projects and want to buy the best tools I can afford and take good care of them.

That being said, I went out and picked this model up today at Lowe's for $159. Exactly as advertised and exactly what I need.

However, there have been some serious reviews from serious users cautioning of the ABSOLUTE NECESSITY of BREAKING-IN your compressor BEFORE USING IT!! Somehow, if you don't break it in properly beforehand, you may be literally wrecking your expensive hardware before you even get to use it.

EXCEPT THAT THE OWNERS MANUAL THAT CAME WITH MY MODEL C2002 (Type 5 I found this in very fine print on the labels on the back of the tank) SAID ABSOLUTELY NOTHING ABOUT "BREAKING-IN." So I did what some reviewers did and looked for an online manual which can be found at this link:

Bottom line is that breaking-in your compressor is MANDADORY, but it's also a cinch.

Here's the exact wording from the online Porter-Cable manual:

Break-in Procedure

Risk of Unsafe Operation. Serious damage may result if the

following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into service and when

the check valve or a complete compressor pump has been replaced.

1. Make sure the On/Off switch is in the "Off" position.

2. Plug the power cord into the correct branch circuit receptacle. (Refer to Voltage

and Circuit Protection paragraph in the Installation section of this manual.)

3. Open the drain valve (counter-clockwise) fully to permit air to escape and prevent

air pressure build up in the air tank during the break-in period.

MY NOTE: this is sort of counter-intuitive as you want the valve to screw UP

toward the tank giving the appearance of being closed when it's actually open.

You will quickly realize whether you're right or not because you WILL hear the

air blowing out the valve. No blowing air?? Turn the screw the other way.

4. Move the On/Off switch to "On" position. The compressor will start.

5. Run the compressor for 15 minutes. Make sure the drain valve is open and

there is minimal air pressure build-up in tank.

6. After 15 minutes, close the drain valve by turning clockwise. The air receiver

will fill to "cut-out" pressure and the motor will stop.

The compressor is now ready for use.

Bottom line: open the drain valve to prevent pressure from building up.

When you turn on the compressor, it will blow air out the valve.

Run for 15 min. Basically a "dry run." No pressure.

After 15 min, screw the valve the other way to close it and let

pressure build up until it shuts off.

You're all set.

Thanks to all the guys that took the time to warn me ahead of time.

I'm grateful and hope this post will remove the boogieman of breaking-in

your new compressor.

Buy Porter-Cable C2002-WK Oil-Free UMC Pancake Compressor with 13-Piece Accessory Kit Now

I've used portable work-site compressors of various types for over 30 years; primarily for pneumatic fasteners and framers. The Porter Cable pancake compressor is, by far, the only one that is truly, comfortably portable, without sharp corners, while at the same time having the PSI and air capacity of six gallons to keep an air-thirsty framer working. I'm amused by the occasional complaints here and at other sites of the Porter Cable not having sufficient power for framing nailers, or that the unit kicks in regularly. Regarding the first commentary, my response is that this compressor has ample capacity to keep two framing nailers busy, PROVIDED THAT the user understands the simple physics in volume air handling. The hose ID is, in actual terms, a secondary stage air tank. The 25 foot x 1/4 inch hose supplied with the compressor is a terrific, light-weight hose and suits the machine's portability. For blowing up things around the home, and filling tires or delivering air to a stapler or brad gun, it is perfect. Having said that, ANY professional carpenter knows that a framing nailer, with its large bore and stroke, gobbles a very large volume of air, which must be backed up with volume that exceeds it. Only a 3/8" hose, or greater, will do that. As to the issue of the compressor kicking in regularly, perhaps some understanding of what's involved with this cycling is needed. All compressors have a turn-on/shut-off tank pressure parameter, whereby the tank pressure never rises above its safe working pressure, nor drops below the design minimum operating pressure. Normally, the action of the regulator allows for the pressure to drop to slightly above the hose supply pressure, at which time it kicks in and recharges the tank to full reserve pressure. Depending on the call for air from the user, this regulation may be more or less frequent, but it should always be predictable, if one were to watch the two dial indicators. When short-cycling occurs, it will be accompanied by a failure of the tank pressure to rise to the full rated pressure of the machine. The cause for frequent, or short, cycling is caused by the presence of water in the tank, which interferes with the pressure regulator. As air is compressed, water--present in all atmosphere--is wrung from it, and contaminates the air tank. This water, if not drained regularly, will eventually rust through the air tank in the long term, but in the short term of only a few hours, will get into the regulator valve, cause short cycling, thus preventing the compressor from attaining maximum stored pressure. Draining the tank must be done once every work-day, minimally, but on humid days, may be required every two or three hours, or whenever short-cycling begins to occur. Small portable compressors simply do not have a provision for collection of water, as large commercial compressors may have. As a helpful hint, the only way to correctly and completely drain the tank of water is to do as follows: Shut off compressor. Pull release ring and allow pressure to drop to at least 30 PSI. Open tank drain cock completely. Tilt compressor toward the valve and wait for the water to blow from it. It may take up to a minute to get it to spit its last, but it's extremely vital for the power, proper operation, and life of the machine. Now, about power... A look at the specs are pretty interesting. Porter Cable's design parameter is 120 PSI minimum to 150 PSI maximum. Their minimum is greater than the maximum of most machines in its class, and the maximum is 15 PSI greater than many machines that top-out at 135 PSI! Now, look at the tank capacity... 6 gallons! Again, it's the gallons of air--the volume--that refills the tool. Of course, such a machine is not ever going to maintain continuous air flow to tools that operate by bleeding off copious volumes of air, but then, such machines are not only not portable, they cost many hundreds, into the thousands, more. Finally, I live where oil-lubed air compressors stop working on cold days. A dry compressor such as the Porter Cable is unaffected by cold, and keeps working. I wonder how many people experience problems with their compressor because they didn't break it in, and began working it out of the box. Read the manual. The compressor requires a 15 minute break-in period, with no load, with the drain valve open. That's key. If you don't do it, you'll have a scored cylinder and air by-pass at the piston, and NO POWER. Your father used to ALWAYS break in his new car engine, because he knew that otherwise he'd be buying stock in an oil company. Even though manufacturers of many motors no longer stress this, it remains a fact that piston motors and engines run longer, more smoothly, more economically, and with greater efficiency after break in. Leakage around piston rings with a new motor is almost always caused by failure to break a motor in. Did you break your compressor in? Hmmmm???

This compressor is the loudest of the ones I've owned in this class, by far, but such is the price for this power, so I would not recommend running it in your bedroom at night.

Buy this compressor, break it in, get a 3/8" hose, and nail away with confidence and gusto!

Read Best Reviews of Porter-Cable C2002-WK Oil-Free UMC Pancake Compressor with 13-Piece Accessory Kit Here

Was using a one gallon Campbell Haus compressor. It was incredibly loud and didn't hold much air. Using it for filling car and atv tires. Wanted more air capacity and quiter use. This Porter Cable six gallon is far better and quieter too. The extra accessories included with the WK version is less expensive than the standard C2002. Very nice unit and well built. Meets all my needs and runs less often due to the 6 gallon tank. Delivered on time as promised by Amazon. Well done!

Want Porter-Cable C2002-WK Oil-Free UMC Pancake Compressor with 13-Piece Accessory Kit Discount?

I didn't buy this product through Amazon, but I read the reviews here thoroughly before purchasing at the local big box retailer. When I bought the compressor, in my first use, the "panel" with the pressure gauges and the air connections began to pivot and turn back and forth. I wrote Porter Cable and they said to return to the store, that this was not its intended functionality. I got my money back, and debated what I wanted to do next. The other compressors that I was thinking of were much more expensive. So, I tried to purchase another C2002, this time I happened to do it at big box retailer #2. I had the exact same problem! I tried to connect a hose and the whole panel turned. This is an issue because the way the panel is attached to the compressor is primarily through the air outlet coming up below from the tank. Although it didn't leak right away, I could imagine what would happen over time and I would just end up having problems. I ended up going back and getting the Dewalt D55146, which was much more compressor that I needed, but it is sturdy, pretty quiet, and works well. On the plus side, I will say that the C2002 was pretty quiet, very portable, and looks nice. Also, I was planning to do occasional framing nailing and didn't need a production compressor, and the C2002 could easily handle the type of work I was doing. I was new to compressors before buying this and in researching them learned along the way that what the compressor can push (framing, brad, etc.) is a function of PSI, not CFM. CFM is essentially a measure of how fast the compressor will return to its max pressure. If you are doing rapid-fire work then you would need a higher CFM but if you're not nailing so frequently a lower CFM like this has would do. I did plug in my framing nailer with 3 1/4 inch nails to the C2002 and it handled them fine. Hope this is useful.

Save 50% Off

I was actually looking for one of those 12 volt dc compressors that plugs into the accessories outlet of the car, but my auto mechanic-brother-in-law recommended that I go with a pancake compressor. I'm glad I took his advise. It's great for keeping the tires on our cars properly inflated, blowing the dust out of air filters and tools, and even cleaning the empty mouse nest out the engine of the garden tractor.

I was originally worried that it might take up too much space in the garage but it's very compact, light, and highly mobile. Great price, too. No post-purchase regrets.

Update: A year later and it's still working great. this last winter one of my tires developed a slow leak that necessitated adding air every other week. Doing so in the comfort of my garage instead of in the snow at the gas station was great. A month or so later a pot hole bent a rim on my wife's car and the compressor again came to the rescue. I have now acquired the annoying habit of checking the tire pressure on my daughter's and son's car when they visit.

Porter-Cable DA250B 1-Inch to 2-1/2-Inch 15-Gauge Angled Finish Nailer

12/9/04 My company owns 3 of these and they really do have a strong shot. We had no problems with getting the nails to set in the toughest materials. Our problems came after 8 mos of use. One of the units began having frequent jams and then started misfiring on a consistent basis. I'm a little concerned because another one of our DA250B nailers has also become somewhat unpredictable and sometimes jams. I definitely recommend the DA250B over the Senco SFN 35 or any Bostich nailers. The Senco SFN 30 and 40 are OK units. My top pick however is the Dewalt Angled Finish Nailer D51275K. All of our crews like this nailer over any of the finish nailers we've used. (Bostich, Porter Cable DA250B, Senco SFN 35, 40, 30). I will say that for the infrequent user either The Porter Cable DA250B or Dewalt D51275K will perform nicely.

Note: We use these finish nailers primarily in oak but sometimes in wood species such as Brazilian Cherry, Mahogany, Rosewood, Maple and other exotic wood types.

Update 07/07/05: I have had each of the 3 Porter Cable DA250B in the shop for repair 1-3 times each within the 1st year. I think it's time to switch entirely to Dewalt. Porter Cable shouldn't mind now since it's owned by the same company now. Also I should add that the Dewalt finish nailer we have is still working flawlessly with the original driver and it gets more use than the Porter Cables.

I have been using Porter Cables 16 gauge finish nailer, and their 18 gauge finish brad nailer, for over a year now. It has performed great. I was doing some tongue and groove cedar on a wall, and wasn't able to get a the nail on the 16 to sit down flush in the upper corner of the tongue. I picked up one of these 15 gauge, the new DA250B, and this thing kicks butt. It is substantially more powerful, than the 16 gauge. POW, their is no mistake about it. What that amounted to, was the 16 gauge would not drive the nail all the way into the inaccessable corner of the tongue. When I tried it with the 15 gauge, it drove the nail in further, all the way to clean with the surface, down in the corner. The 16 gauge took it to the extent the tip would go, but the 15 gauge went beyond the restriction, all the way to a flush finish. So you could say, the tongue extends out farther on the 15, like beyond flush. It is not the air pressure, I'm running it on a 6HP 60 gallon tank, or the setting of the head depth, I played with all of those. It simply is a more powerful machine, and the tongue appears to extend more, to drive the nail deeper in situations where you can't get the head all the way in a corner. It drives it in anyway.

I would like to make a comparison. It is like comparing the 18 gauge to the 16, but moreso. Maybe it is the new technology, but this thing kicks. The second you fire the first nail, you know it, before you even look at the result. It does leave a larger hole of course, and it has a slight D-shape to it. Reminds you of the old hand forged nail look, but on a finish nail size, and it is a little hole, rather than an exposed nail.

You will notice that Porter Cable states that it is improved to accept other manufacturers nails. I think that may be the nature of the problem some others were experiencing with the older model. They put strange nails in the gun, but now it can accept them.

I highly recommend it, and I expect it will give me the same reliability the 16 and the 18 have given me over the year.

Buy Porter-Cable DA250B 1-Inch to 2-1/2-Inch 15-Gauge Angled Finish Nailer Now

I was building a cabinet the other day and using this nailer, and man, I tell you, you could feel and hear the power of this puppy throughout the shop. It fired rounds of 2" nails in solid oak and with every shot, there was a consistent message being sent out to the wood, "don't mess with me"!

When working with solid hardwood material, and finish nails, the last thing that you want is your nails to be proud of the surface where you have to go back and set them all manually, or the nailer leaving an ugly mar on the surface. None of that with this baby;) It sets the nails and does it exactly where you want them. Very nice tool!

Read Best Reviews of Porter-Cable DA250B 1-Inch to 2-1/2-Inch 15-Gauge Angled Finish Nailer Here

I can't think of a single thing that I would change about this gun. It loads easily, it is well balanced and not too heavy, the drive depth is easy to adjust, and it has never jammed even though I drive mostly 2-2.5 inch nails. I also have a 2 inch brad nailer and that may be sufficient for most people who are only going to nail molding. But for applications that require a 2.5 inch long nail or more structural support, this nail gun is perfect. I bought mine reconditioned for about a 20 percent savings and it has worked flawlessly and looked brand new.

Want Porter-Cable DA250B 1-Inch to 2-1/2-Inch 15-Gauge Angled Finish Nailer Discount?

I would give it 4.5 stars but that is not an option. I got this one for xmas, I guess the wish list on amazon does work (hehe). Just finished up a basement finsish, shot about 4 boxes of 2.5" and 2" nail through it, not a one miss or jam (watch me jinx myself). I do know that porter cable has completely redesigned the "B" version of this gun, maybe all the negative feedback for it was for the "A" version. I can't complain about this nailer, not in the least, except it seems to be slightly inconsistent in the "blow out" in the wood. It feels light in your hand and the adjustable exhaust is great.

Save 35% Off

Senco PC0968 Compressor, 1.5-Horsepower (PEAK) 2.5-Gallon

• Electric, hand-carry design
• Oil-less
• Weighing in at only 38-pounds
• 2.5-gallon tank storage.
• 135 PSI max pressure

This is a great, comparatively light, little compressor that drives my stapler; brad driver, 15 and 16-gauge finish nailers with ease. I have high expectations for any Senco product, so I did notice one minor design flaw if you plan to use a filter at the compressor connection.

The compressor's female quick release is facing more toward the roll bar frame instead of being angled away from it. There isn't enough physical space to clear a large in-line air filter, so instead of changing out the factory release, I simply used a swivel fitting on the air line (see my photo) to angle the filter and hose away from the frame. No big thing.

The stacked tank design doesn't seem to be as loud as pancake compressors, but is about what you would expect of a 1-1/2HP compressor. I still intend to fashion a noise shroud for indoor and woodshop use.

I should also mention that it took two tries to get a compressor delivered that wasn't damaged in transit. Damaged compressors seem to be a common problem at Amazon (read the horror stories under Makita) but this is attributable to bad compressor design, as much as rough handling during shipping. My compressors arrived by UPS, double-boxed with newspaper packing in between, yet the first compressor had a smashed pressure gauge inside. The inner box, from Senco, was not damaged in any way. So that must mean the gauge was damaged and shipped out anyway at the factory???

I have to praise Amazon Customer Service who replaced and delivered a perfect, new Senco compressor in just 72 hours--can't ask for better service than that.

Buy Senco PC0968 Compressor, 1.5-Horsepower (PEAK) 2.5-Gallon Now

This is a great little compresseor. I have a small contracting buisness and this compressor is light enough to carry through a house. It is quiet enough not to force everyone out of a room. It also is capable enough to handle finish work through light framing that you do in remodling work.

Read Best Reviews of Senco PC0968 Compressor, 1.5-Horsepower (PEAK) 2.5-Gallon Here

the Senco costs more than comparable capacity compressors but the quality of materials, workmanship, quietness, and reasonable weight (37#) made me happy to have paid the premium. I was doing a remodel job that required using a framing nailer....got 10 to 12 nails before the unit quickly and quietly recovered.

Want Senco PC0968 Compressor, 1.5-Horsepower (PEAK) 2.5-Gallon Discount?

I purchased this Senco Compressor after reading other positive reviews and I'm not disappointed. The unit is well-constructed and appears to be built to last. The pressure relief valve makes it easy to bleed air and the drain valve is brass and easy to operate. I especially like the quick on-off lever and the pressure limit control. All air fittings work as expected. The unit weighs little enough so that it's easy to transport using the well-balanced handle. Noise is something that all of these small compressors produce but the PC0968 doesn't make too much of it at least in my subjective opinion.

Save 15% Off

After researching the "smaller" compressors, the pc0968 was a perfect match. Billing was easy, shipping was quick, and the little guy works awesome. When the box came, I thought it was a toy. All around, great little unit. Lightweight, very, very, VERY quiet, super fast to pump up and recover. Haven't tried my framer yet, but I'm sure she will do ok.

Campbell Hausfeld CHG00100AV 1-1/4-Inch 2-in-1 Brad Nailer/Stapler Kit

• Ideal for upholstery, installing trim, installing chair rail and crown molding, building crafts such as picture frames and birdhouses
• Drives both 18-gauge brad nails and 1/4-Inch crown staples, 3/8-Inch to 1-1/4-Inch length
• Easy maintenance with included oil bottle
• Includes starter fasteners
• Includes blow molded storage case

Garbage....Arrived DOA....Ordered unit for an upcoming project. Connected it to the compressor and immediately heard air leaking from the front of unit. Tried to use the nailer and it would not fire. I am now 31 days past my order date and can not return to Amazon. Will try to contact the manufacturer regarding warranty.

Buy Campbell Hausfeld CHG00100AV 1-1/4-Inch 2-in-1 Brad Nailer/Stapler Kit Now

I purchased this to use on a couple of custom end tables I was building for my 5th wheel trailer. It worked flawless, so good in fact I went back and bought the 2" as well. This stapler is light weight and comfortable to handle. It fires true each and every time and what a bargin at this price. I couldn't be happier and would highly recommend this to anyone. Happy nailing !

Read Best Reviews of Campbell Hausfeld CHG00100AV 1-1/4-Inch 2-in-1 Brad Nailer/Stapler Kit Here

I had to buy this at my local Lowe's store because I needed it that day. The Gun works excellent and come with 1" nails,staples,oil,three Allen wrenches & a case. I went threw three rows of nails and the gun worked perfectly and I completed the job without any problems. What a difference a nailer makes to give the job a professional look and save time. Great buy !

Want Campbell Hausfeld CHG00100AV 1-1/4-Inch 2-in-1 Brad Nailer/Stapler Kit Discount?

I used it a couple times, with staples and brad nails and both times I was pleasantly surprised at its ease and flawlesness of use. Would definately recommend it. Used with a tiny pancake 1 Gal compressor with reservations, but again great performance. I am trying to come with a reason to use it again!

Save 56% Off

First time owning an air nailer/stapler so not much to compare to, but it worked great for me. used it with my porter cable 6 gal pancake compressor to attach some wire fencing to my split rail fence (and in some areas directly to some trees too many roots for split rail fence). It sent 1 inch staples through with no problem with the compressor set at 100psi. felt very sturdy, comfortable, and like it could re-fire very quickly and go for a long time. Hard to find 1-1/4 inch staples at a good price.

Ingersoll Rand 2130 Protective Tool Boot

• Keeps tools clean and protected
• Bright red color makes it easy to locate your tool in a busy shop

The boot I got is black, and not the red one in the picture. Amazon should update the picture. It seems to be quite durable so far, and is a tight fit. It took some stretching to get it on.

Buy Ingersoll Rand 2130 Protective Tool Boot Now

Ingersoll Rand 2130 Protective Tool Boot

Contacted Amazon to have the picture changed from the RED boot to the correct BLACK boot picture.

Very happy with this purchase and included some pictures of it installed for your reference.

A very tight fit indeed but would not want it any other way.

Buy this tool protector with confidence.

RagenRat :0)

Read Best Reviews of Ingersoll Rand 2130 Protective Tool Boot Here

Does what you expect, fits well and protects the tool. You don't even really know its there it fits so well, except around the reverse switch. Color on mine was black, read carefully when ordering as red is shown.

Want Ingersoll Rand 2130 Protective Tool Boot Discount?

Purchased this boot for my Ingersoll Rand 2130 impact wrench and it works great. Like the previous users mentioned the boot fits very snug. I heated up the boot with a 1500w hair dryer about 10 seconds to soften up the boot plastic a bit and it made it much easier to work it onto the impact gun. Once on it is indeed very snug and the protection it offers is worth the additional cost.

Bought this to fit over my 2130 ingersoll rand impact gun. Fit was great and protection will be great,too. Covers the gun great and yes the fit is tight,but needs to be other wise it will not protect like it should and with it fitting loose you will fighting it being in your way. Yes I would recommend this.

12 Volt Mini Automotive Air Compressor Complete with a 0-250 psi Gauge.

• Mini Air Compressor Nifty device that takes maxi air and squeezes it down into a mini condition. The device is roughly 6-1/2"" long x 6" tall x 4" wide. It has a 10 ft.
• cord that plugs into an auto lighter socket: i.e it runs on 12VDC @ 10 amps. Air output is via a 12" hose with a variety of valve adapters for tires, soccer balls, rubber rafts, and just dusting off the environment.
• Complete with a 0-250 psi gauge. Which should be plenty of pressure to explode a weak bike tire or flimsy beach ball, so please be careful!

TO FOREVER TO TO PUMP UP TIRE IT MIGHT BE COOL FOR A BIKE , BUT NOT FOR A CAR TOOK SO LONG i ENDED UP GOING TO GAS STATION , i CANT RECOMMEND IT

Buy 12 Volt Mini Automotive Air Compressor Complete with a 0-250 psi Gauge. Now

S-L-O-W-L-Y

Bring a book.

I would call this emergency equipment, in a pinch it will inflate a car tire but at first I thought it didn't work, then five minutes in I noticed the gauge come off the pin. I was inflating a compact car tire from 15 lbs, I would guess 10 15 minutes to 26 lbs. The gauge is impressive looking but 5 lbs low. The cord is somewhat short to get from the lighter socket to the spare hung on the rear gate. It gets HOT when you run it Esp the fitting where the hose comes off the pump. The chuck is very tight, requiring some force to really put on and remove. My recommendation: spend more money and get a real one if you need to inflate things in a reasonable amount of time.

Read Best Reviews of 12 Volt Mini Automotive Air Compressor Complete with a 0-250 psi Gauge. Here

Works fine so far. as usual these cheap compresers air gauge is junk. and on thing i would add to this is an on and off switch.