Stanley Bostitch CWC200ST 3HP 4-Gallon Oiled Twin Hot Dog Compressor

• Bostitch Twin Hot Dog Compressor with 3-horsepower, 15-amp induction motor
• 5.1-cfm @ 40-psi and 4.0-cfm @ 90-psi; dual air outlets
• Cast-iron pump cylinder for extreme durability
• Includes panel with regulator gauges and hose port
• Backed by 1-year warranty

I bought one of these compressors a couple of months ago after doing carefull research and actually going to a repair facility here in AZ that handles warranty repairs for a variety of brands. Comparing quality versus price the Bostitch CW200ST was a winner.

So I bought one to use with a Bostitch nail gun and stapler while restoring my parents house. I estimate that the compressor has about 15 (fifteen) hours of use by now. The oil pump reaches pressure rather quickly but the pressure regulator cuts the power at 120 PSI rather than 125 PSI as prescribed. The condensation drains are installed in a bad place and when open do not drain because they are too high on the tanks I estimate that it will have over a QUART of water inside each tank before any will reach the drains. You will have to tilt the compressor down and rock it side to side to get the water out, furthermore when tilted the lower drain hits the floor impedig drainage so you actually have to lift this rather heavy machine and tilt it and rockit at the same time in order to drain...A real pain!!! the handles are not in the right places and the unit does not balance well at all.

Shortly after purchasing the unit one of the Quick Disconnects on the compressor will not seal itself after the hose is taken off and will merily leak all the air out in about one minute, I had to replace that so I could use the machine. It is rather cumbersome to unscrew the disconnects as they are too close to each other and the pressure Gauge. For about the last five hours of use I started to notice that if left pressurized overnight the air was gone in the morning upon closer inspection I could hear a faint hiss comming from somewhere behind the regulator It was not much just enough to leak and turn the machine on about every 15 minutes even if I did not use air. Yesterday the manual regulator prooved to be the culprit as when I started the compressor for the first time it would not hold air at all. The two halves that make the assembly where the manual knob is placed have came apart where they are threaded together. I took the disconnects off and loked at the problem. It looked like vibration had caused the two parts to came undone. I Screwed them back together and put some red thread locking liquid on them. I put everything back together and left it overnight to set. Today I power it on and it run up to the regular 120 PSI. I put my head next to it to listen for the noise of air escaping and sure enough there was a faint hisssss... While I was trying to figure out where the noise is caming from The back of the manual regulator popped loose again suddenly letting all the air escape in an instant startling me and prompting my wife to ask from the kitchen some ways away: "did you do that on purpose?" Well NO. The Zamak threads are soft and do not mesh.They are too loose and thin hence the problem. The machine is unusable untill I get a replacement hopefully of beter quality. Unfortunately I have to get the exact size and probably same model since it mounts on the front panel with a plastic threaded ring and space is rather limited and, it neds to have the same ports and orintation so it can take the various hoses and ports connecting to it... Overall the tech was right the actuall compressor is well done I believe he said it was Italian made the rest is rather sloppy and not thought out well. There is a small tag on the unit, it says: "Made in PRC" I don't think that is nowhere near USA

Buy Stanley Bostitch CWC200ST 3HP 4-Gallon Oiled Twin Hot Dog Compressor Now

Had this unit 1 month and the motor locked up, took Bostitch repair center 3 weeks to fix, told me it was a common problem they were seeing with this unit. I wish I bought the Makita instead.

***6 month update---broke again, this time I am getting it fixed and selling it...and buying the Makita...I have 4 Bostitch nailers and like them..VERY dissapointed in Bostitch on this one, Bostitch customer service has been no help.

Read Best Reviews of Stanley Bostitch CWC200ST 3HP 4-Gallon Oiled Twin Hot Dog Compressor Here

The motor on my compressor consistently sticks, even when connected to a 20 amp wall circuit. I have taken the compressor in for service, but the problems persist. Generally, I like Bostitch tools, but they really missed the mark with this one.

Want Stanley Bostitch CWC200ST 3HP 4-Gallon Oiled Twin Hot Dog Compressor Discount?

I've had this compressor for about 6 months, but only recently have been able to test it with some projects.

I really like it a lot. It builds up pressure quickly, and powers my air tools without any problem. I don't lose any performance when I run it under 90PSI and it needs to kick in again. It's not really all that noisy unless you're right next to it, and you can easily hold a conversation while it's running in the same area.

I haven't had any problems with it at all, and am looking forward to many years of service from this tool.

Save 5% Off

i've had this compressor for 3 years. it froze up about a month after i purchased it, repair facility was fast, and put a new motor on swiftly.

it will not work in cold weather. it's an ordeal trying to get it to cycle in weather less than 40deg.

i think the problem is the motor, I say this because a shopmate bought a rigid mini wheel barrow compressor that has a visually identical compressor motor on it, and it doesn't work well in cold weather either. My shop is not heated, so on cold days we have a contest to see who can get their compressor running first. that's when we're in a good mood, often when you are working on a cabinet or somesuch, you hear the motor click on but not cycle and you curse under your breath because it's a pain in the butt.

as i speak it has an audible leak in it's regulator somewhere. it ruptured the hose from the regulator to the shutoff valve once before, it was loud and happened in a clients home.

so, after three years of consistent use it's still going, but not without a lot of help along the way.

if i could i'd look for a model with a completely different motor assembly.

and if i had my $250 back.

Typhoon Pro Blow Gun

This is a great product. I bought the pro version to get the all-metal design (the product picture is wrong), and I'm glad I did. Super high-quality design, feels just right in the hand. The amount of air this thing puts out is awesome, just shy of leafblower status. It is quieter, smoother operating, and in my opinion safer than conventional blow guns because it doesn't have a single orifice. Totally worth the $27 I paid including shipping, and I would recommend the pro model.

Hitachi NT65M2 16 Gauge 1-Inch to 2-1/2-Inch Finish Nailer

• 16-gauge finish nailer with selective actuation for sequential or bump firing
• 360 degree adjustable exhaust directs air away from the user
• Tool free depth of drive; easy clear nose; elastomer grip
• Includes tool fitting, safety glasses, no-mar tip, hex bar wrench, and case
• Weighs 3.7 pounds; 5-year manufacturer's warranty

I have used this gun now to do quite a bit of siding, using wood siding and fiber cement trim. I have fired short finish nails and longer 2 1/2 inch nails (capacity). It has never, never jammed and never failed to fire if I remembered to turn on the compressor and to load in nails! There have been times that I drove a longer nail from one corner trim piece of fiber cement 1 X 6 into another and it didn't sink all the way, but it was silly of me not to change to shorter nails, so I don't blame the poor gun!

It's pretty, so you'll be tempted to treat it gently, but that isn't needed... it's a toughy!

Buy Hitachi NT65M2 16 Gauge 1-Inch to 2-1/2-Inch Finish Nailer Now

I'm building a log home and bought this nail gun to install the tongue and grove ceilings. I've used over 4,000 nails so far and have had absolutely no failures. It is light enough to operate overhead all day and at 80 psi will seat a 2" nail under the wood's surface. It fits the hand well and is fully adjustable without tools. The only negative I can find is that it has no way to hang it up while fitting a board. I use it with a small 2.5 HP, 4.2 CFM compressor and it will shoot 12 nails before cycling the unit. The nails are easily available on-line or at your local big-box store and this gun is not fussy about what brand you feed it. I liked it so well that I went back and bought it's big brother, the Hitachi framing nailer (but that is another review).

Read Best Reviews of Hitachi NT65M2 16 Gauge 1-Inch to 2-1/2-Inch Finish Nailer Here

Pros:

-exhaust can be rotated (air in the face is annoying and dangerous)

-button to spray air (very handy for bleeding compressors at the end of the day)

-great weight and balance, extremely comfortable

-jam clearing mechanism is super easy to use (haven't had a jam yet though)

-very consistent depth of drive

-comes with air fitting pre-installed (no need to buy)

Cons:

-don't like the tip style as much as my other nailers

-no lockout mechanism to prevent dry fire

It's worked well for me on furniture projects, and I don't have any major complaints. It's a great nailer (maybe even the cadillac), but I probably wouldn't recommend it to any of my amateur woodworker friends, because they can get something else to do the job at a fraction of the cost (lots of good nailers on the market right now).

Five stars for quality and design, but only three stars for value. In the end, it's still a five star tool.

Want Hitachi NT65M2 16 Gauge 1-Inch to 2-1/2-Inch Finish Nailer Discount?

Lightweight and I haven't had a jam in over 3 cases of nails hanging beaded pine ceiling. I read a review when I purchased the gun that said "The gun feels like an extension of your hand." They were right.The air blowing feature seems a bit pointless, but it doesn't affect anything.

Save 63% Off

The spray button is a nice touch. A solid gun, although hideous, and the grip and trigger are nice. No jambs to report. I actually shot 18ga nails in a pinch out of this gun (not recommended!) but it shot them two at a time for a while and still didn't jamb! Why they made it look like an alien respiratory system, I don't know, but form over function here, it's really not a beauty contest. The only (minor) complaint I have is that the large round head/tip is not perfectly tailored to small 2 5/8 crown moulding. It is still possible to get it where you want it to sink the nail well, but if you don't use the tip right you may have to set 1 out of 20 with a nailset which is fine if you keep it in your belt. I do think the tip is fantastic and sturdy in all other situations. Maybe I should just use 2" brads for that mould.

Campbell Hausfeld HVLP Turbine Paint Sprayer - 4 PSI, 0.06 GPM, Model# HV2002

• 2-stage turbine assist HVLP paint sprayer (no compressor needed)
• 54 CFM
• Durable construction delivers consistent coverage
• Metal pattern adjustment for round, vertical, or horizontal spray patterns
• Metal air flow control can adjust pattern from 1/4in. to 6in.

I purchased the CH HVLP sprayer as an alternative to a compressor plus gun setup for spraying clear finishes as well as interior trim paint. The previous CH products that I had purchased had been great. This one has been a great disappointment.

First, the transfer of material to the surface being painted appears to be about as inefficient as a normal high pressure sprayer. This is especially true when spraying higher viscosity coatings that require more airflow in order to move them. The second issue is the fineness of the spray pattern. This unit produces a pretty rough and uneven pattern compared with other units. The air supply hose is a real handicap as it is not only too stiff for easy use, but it has a really nasty chemical smell that just doesn't go away.

Summary, I have a CH compressor, an airless sprayer and this HVLP. I can reccommend the first two without hesitation. This last is just not worth it. Get a Fuji, Apollo or perhaps the top of the line Wagner. They are all $500 or more, but at least they do the job.

Buy Campbell Hausfeld HVLP Turbine Paint Sprayer - 4 PSI, 0.06 GPM, Model# HV2002 Now

I am so impressed with this product and I too am surprised by the not so great reviews. I have a feeling that the people who don't like this product are people who have significant experience with other paint sprayers . . . People who like to thin the paint, tweak knobs, make adjustments, etc., etc., etc. This is a ($) paint sprayer. . . it doesn't have a lot of knobs and whistles and probably isn't very forgiving in some respects (compared to ($) paint sprayers).

This was my first time ever using a paint sprayer. I read through the manual, (especially the part where it specifically says to not mess with anything), poured in the paint . . . and I was off spraying (I didn't need to thin the paint!). There is only one knob to adjust the volume of paint that is coming out . . that's all that I needed. It worked great and the finish is smooth and even (I painted my veneer kitchen cabinets using a BIN primer and an Alkyd based semi-gloss).

This is the perfect paint sprayer for the do it yourselfer. Just RTFM and don't mess with anything. Also, pick paints that don't require thinning (the one's I used specifically stated that you shouldn't thin it . . . RTFM)

Read Best Reviews of Campbell Hausfeld HVLP Turbine Paint Sprayer - 4 PSI, 0.06 GPM, Model# HV2002 Here

I own this sprayer and it is not woth the money. You cannot get a fine spray pattern from this unit. The air cap is poorly machined and the turbine does not supply enough CFM. Spend more money and get an Accuspray system.

Want Campbell Hausfeld HVLP Turbine Paint Sprayer - 4 PSI, 0.06 GPM, Model# HV2002 Discount?

I started a started a project of painting my kitchen cabinets with rollers and brushes. I had 2/3rds of the primer on and just gave up, it was too time-consuming and difficult. I logged on, found this paint sprayer and have just completed the project. I've never used a paint sprayer before but found this very easy to use. Only one knob to control the flow and a trigger to spray. Very easy. The paint applied beautifully and it looks professional. I was worried about runs in the paint, but it rarely happened; only if the sprayer got too close. I used if for both latex and oil-based enamel. At first the oil-based paint would not come out. I discovered I was not thinning the paint enough. It is easy to disassemble and clean. I am never going back to brushes and rollers.

I use this sprayer for a number of household projects: varnishing, painting, etc., and haven't encountered the trouble the other users have. I'm sure there are better HVLP sprayers, but at twice the price? Unthinned latex is applied rough, but it smooths as it dries, and thinned latex is applied plenty smooth -much smoother than a brush. Perhaps if you need a sprayer for high gloss finishes, you may need better, but for semigloss trimwork and varnishes, this does the trick just fine for me.

Tool Force A-C1 50 PSI 2-in-1 HVLP Spray Gun

• 50 psi 2-in-1 HVLP spray gun offers high atomization with low nozzle air pressure
• Better than 75% transfer efficiency with less than 10% psi output pressure
• 1.4-millimeter stainless nozzle for lighter materials; 2-millimeter stainless nozzle for heavier materials
• 1/4-inch air inlet
• Requires a 2 to 3 HP compressor (not included)

I paint houses, vehicles, motorcycles and equipment. One of my Airless sprayers cost over $5000. The automotive sprayers (Devilbiss) are about $500 each. I've always wanted to get an HVLP spray gun. But, with so many available and with such a wide price span, I decided to start with something inexpensive and see how they function.

When I took this Tool Force sprayer out of its box I could see and feel it was much, much nicer that the price I paid for it. There isn't anything cheap looking about the sprayer. The head, needle and the body emulates the quality of my guns ten times the price.

I've paid more for just a needle kit for other sprayers.

I started off spraying Latex paint. I knew I had to thin it, and it wouldn't deliver the volume equal to the Airless. But, after tinkering with the air/volume/fan adjustments it's performance actually amazed me. It is fantastic on small projects. It easily opens up on big areas and tones down on intricate areas. Loose the Air Regulator and install a light whip hose and this gun gets everywhere, at all angles. The material in the cup weighs almost as much as the whole gun. It still worked good with a small compressor, but it performs best with a big compressor with more air volume.

I tried using a few of those 'electric' guns. Besides being inefficient, they are Very noisy and heavy.

After a couple hours use, I cleaned almost the whole Sprayer with just water, then a little lacquer thinner to make it look like new again. My airless sprayers takes 2 hours to disassemble the pump, filter, hose and gun, and a gallon of lacquer thinner.

So, I'm now considering purchasing a Nice HLVP. But this one has such an even delivery of material, a perfect conical spray pattern and fantastic control with all the available adjustments..... I'll have to see what other models they have. Maybe another cool color.

Buy Tool Force A-C1 50 PSI 2-in-1 HVLP Spray Gun Now

I picked up this gun to spray oil based urethane on my front doors. It was impossible to get a smooth and even finish with a brush with Varathane's satin urethane I tried twice. So, although I have never used a spray gun, I deciced to give this one a try and see if I could get a satisfactory finish. I was not disappointed with the end result. The finish is far better than can be achieved with a brush. Just be prepaired for a little learning curve when learning to spray.

Internet searches will give you tips how to hold and move the gun, what tip sizes are needed for your type of work, pressure settings etc. Then practice on a piece of scrap. Even after doing all of this homework, I still managed to get a run on the first side of the first door. A little more experimenting revealed that I had the pressure too low (30 psi). I turned it up to 40 and presto! Easy spraying and a smooth finish. The information avaliable will tell you to use the lowest pressure possible but but my experience is don't be afraid to turn it up a bit for varnishes.

What I really liked about the gun:

Great price

Easy to clean (takes maybe 5 minutes compare that to a big paint sprayer!)

Has a pressure guage and adjustment at the gun. This is important because the pressure at the compressor may be different than the pressure at the end of the hose.

You get two useful tip sizes

Read Best Reviews of Tool Force A-C1 50 PSI 2-in-1 HVLP Spray Gun Here

I used this HVLP for spraying on Second Skin Audio's Spectrum Spray sound deadener and it worked GREAT! The provided 2.0mm nozzle worked awesome for spraying the very thick product at a reasonable 40-50 PSI. The adjustable fan spray was very accurate and allowed me to get into the very tight areas with ease. And VERY low excess "particulates" in the air while spraying which is very nice.

The provided pressure regulator is a nice addition, but wish it were of higher quality, then again I wouldn't expect much more from a $20-$30 HVLP gun.

The only real complaint is the trigger, when using the gun for a period longer then 15 minutes your hand and fingers get fatigued, but applying some PlastiDip or other similar product helps.

All in all a very reasonably price HVLP gun that does a decent job.

Want Tool Force A-C1 50 PSI 2-in-1 HVLP Spray Gun Discount?

The gun arrived quickly and worked well right out of the box. It took a minute or two to get the adjustments dialed in, and then it was off to the shop

I was painting a wood cabinet that was previously primed with Kilz.

I used new ACE latex acrylic enamel semi-gloss and the 2.0 tip

I thinned the paint with a bit of water and added some Floetrol to slow drying.

It works nice at about 45 psi on the regulator

Much easier and quicker than brushing and the finish is very smooth.

Save 52% Off

I've been using this sprayer over the past month to spray varnish onto wood-strip canoes. After dialing in a bit too much flow the first time and getting a few drips, I cut back on the amount of varnish and set the pressure dial to about 35 whatevers, and I've gotten coat after coat of smooth and quick layers. I love this thing! I'm running it off a 6 gallon Porter Cable pancake compressor, and it works fine as long as I pause when the pressure drops too low. Repeated cleanups have been pretty quick and easy, too, with only one clog when I didn't get enough varnish/thinner out of the front spray holes. Great price for a great product!

Poly IND Fit Air Hose

Yes, its light and flexible as others have suggested. These are great things to have in an air hose. The fact that its hard to kink is somewhat irrelevant because under pressure, I've never experienced a kink in my regular rubber air hose.

This hose just continues to annoy me though. The big problem is that it wont lay flat on the floor. It will lay twisted and semi-coiled no matter how many times you unwind or untangle it during use. The coils on the floor create 6 to 8 inch "bridges" of hose that you will inevitably trip over, become tangled in, and then curse like a sailor. I cant count how many times the hose has literally wrapped around my foot by accident. I'd bet that 25% of those instances caused me to mis-step or flat out trip and stumble. My good old rubber hose lays flat on the floor and has never caused me an ounce of disgust. And the rubber hose is much easier to re-coil for storage.

This is not an issue limited only to these Hitachi hoses. I've yet to find a polyurethane air hose that lays flat. You see, the trade off to the "lightness" of the hose is that it causes it to lay at its own will (seeming to disregard gravity). I'm not even sure you'll understand the point of my review. If not, go ahead and buy one. I think my comments will be clear within a matter of minutes.

Regretably, I bought three of these hoses before I realized what a pain in the rear they are.

We just ordered two more of these from Amazon (they are significantly cheaper at the moment than the local stores). These are the favorites among our construction company due to the light weight, durability, and the fact that they really don't kink.

For those of you who are just working around the house, any old hose will do. But for those of you in the professional arena, the lighter weight will be a blessing in the 8th hour when you're trying to get those walls up before dark so that you can get paid in the next draw. We stick with the 100 lenght because we are building hotels and such, besides going from the 50 to the 100 is only a few dollars difference and is worth it if it keeps you moving.

Highly recommended

Buy Poly IND Fit Air Hose Now

This is a great hose and an excellent price. I am a carpenter and framer and use my nail gun all day long, every day. I bought this hose about 6 months ago, it is very lite-wieght and flexible and does not have a single shortcoming. Stretch the hose out in the sun when you first get it and wrap it up loosely each nite to keep it from kinking up. Also, you might want to go ahead and order some universal attachments, as the hose comes with 3/8ths only.

EDIT: Been using this hose every day for more than a year. In that time it has not had a single leak and has performed flawlessly, excellent value.

Read Best Reviews of Poly IND Fit Air Hose Here

Let's you get the compressor away from the house and are tough as nails. Very little wear on these with three months of hard use. A little side note: these are clear and lets you know if your building up condensation in your tank and might be getting a little rust.

Want Poly IND Fit Air Hose Discount?

Im a residential building contractor and these airlines are the best ive used. I really like them doing framing and trim cause the cold weather doesnt affect these airlines. I have noticed their very durable as well cause my guys dont bother climbing and hand off the nail gun they will lower it down to the person below using the airline and the fittings hold up great. I wont use a different airline thank you hitachi for designing such a great item for guys that use them every day and they keep going. I hope my review could help in choosing a airline you wont be disappointed.