- Lightweight and portable--easy to carry from site to site as you work
- One horsepower peak ,1/2 horsepower runningand one-gallon capacity
- Ideal for a range of renovation and home improvement jobs, as well as for hobbies and crafts
- Delivers 20 to 44 drives per minute
- Backed by a one-year warranty
This is a great second compressor. I wouldn't buy this as a primary or first compressor but it works fine to support small nail guns. My other portable weighs 68 pounds and will keep up with 1 to 2 framing or roofing nailers. My shoulders ache from the number of times I have lugged it up 78 steps to a job site. This goes anywhere with a bunch of tools in the other hand.
Other than nail guns, NO it won't do much at 0.7 cu ft per min when paint spray guns need 10 times that, and a blow gun will empty the tank in 10 seconds or less. But seriously, this compressor gives me at least 10 shots from my 16 ga finish nailer before the motor kicks in; a couple more off of an 18 ga finish nailer, and as an acid test, I got 3 shots from a 3 1/4 inch framing nailer (not recommended but if all I need is 10 nails I'd rather carry this in especially considering that my ripe old age keeps me from doing much serious hammering!)
Last word, the first one I received had a leaky reed valve and it had to be replaced by Amazon I'm very happy with the replacement and have used it on several job sites.
Buy Senco PC1010 1-Horsepower Peak, 1/2 hp running 1-Gallon Compressor Now
As a general contractor I have several compressors. At least 90% of the time I grab an Emglo because they do everything I need except texturing. But I've grown fond of this little Senco WHEN IT IS USED PROPERLY! That means if I have a small trim project or a VERY small framing project it does the job, and both takes up less room and is a lot easier to pack around. It'll drive 3" framing nails no problem...when the tank is topped off, but the last couple nails before the compressor cycles always need to be hammer finished. Same is true for 15 or 18 gauge finish nails. When the tank is just about to cycle the nails don't completely set. My workers love the Senco...much to my chagrin. For one, it's light, and second...it takes FOREVER to refill (relatively speaking) and my guys love to stand there with their thumbs you know where taking a break every 10 to 15 nails or so! So if used for small jobs...or trim where you nail one piece at a time while cutting, well then it's a champ. But if you tend to cut trim for an entire room, then want to shoot it on quick...this Senco will frustrate you no end. You end up hand nail setting too many nails, or else you have to stop frequently, unhook the air hose, drain a little air from the tank until it cycles, then wait for the darn thing to fill. If you use it right... 5 stars. If you use it as your go to compressor... 2.5 stars tops. I hope this helps!
Read Best Reviews of Senco PC1010 1-Horsepower Peak, 1/2 hp running 1-Gallon Compressor Here
For my applications of easy carry in and out, it's been terrific for lightweight 18ga. finishing.
On a small renovation project yesterday, 4 doors jambs and trim were easy (1" to 2" 18/16ga brads) The very least of my problems was waiting for the little Senco to catch up. Been using it for about 5 months, shot about 10,000 brads. So far it's been flawless.
Very low noise as compressors go, and neat little rubber suction feet that keep it from skidding around and marring up a nice floor.
Want Senco PC1010 1-Horsepower Peak, 1/2 hp running 1-Gallon Compressor Discount?
I purchased this model based on web search results showing it to be the quietest (69dB) small (1 CFM) air compressor on the market, and generally high satisfaction of other owners. It is indeed very quiet, well made, and lightweight.
I've mounted this compressor in an acoustic chamber that I designed to further reduce the noise, and it is now as quiet as the "super silent" compressors used for indoor craftwork (airbrushing) that cost $600 to $1000 (49dB). At this further muffled sound level, I can operate the unit all day long sitting next to me without discomfort.
I highly recommend this model for indoor craft work. I've used mine for 40 to 50 hours and had no troubles, but feel this unit will hold up for a long time. I will use this in my home for a few hours per day.
Save 17% Off
I purchased this compressor after actually using one on a jobsite. A fellow trim carpenter had recently purchased one and allowed me to try it out. WOW !
It is extremely quiet and an absolute pleaure to carry around !!! I normally run a Senco 15 gauge trim gun along with a Senco 18 Gauge nailer and a Grex micro pinner. Most of my work involves hanging and trimming doors/windows, crown mouldings and chair rail work.
The compressor will power all three guns one gun at a time. I read reviews on this site all the time where reviewers complain about a tools lack of power. IT IS A ONE GALLON COMPRESSOR !!! You can't run a framing nailer with it and even with the 15 Gauge nailer you have to take your time and allow the compressor to refill after 5 or 6 shots!
The trade off is that it is LIGHT and QUIET ! If you have to go one hundred miles an hour, you're probably not doing a quality job in the first place.
This unit shipped from Amazon by FedEx and arrived in a double carton without any damage plus FREE SHIPPING !
If you need a small jobsite compressor for trim work or punch-list items look no further. It is a pleaure to use. Just remember it's not designed for speed !
