GOODYEAR 46512 3/8-Inch by 10-Feet 250 PSI Lead-In Rubber Air Hose With 1/4-Inch MNPT Ends

• Solid Brass End Fittings: 1/4-Inch MNPT
• Spiral Synthetic Yarn Reinforcement
• Abrasion-Resistant Rubber Outer Jacket
• 100% Made and Assembled in the USA
• Hose ends are male / male

This is just what I needed to have a detachable connection between my air tank and my permanent RapidAir lines. Now I can disconnect the short hose and move the compressor if I have to. The rubber hose and fittings seem to be of good quality, made by Goodyear in the U.S.A. The hose is very flexible, bending without kinking.

Buy GOODYEAR 46512 3/8-Inch by 10-Feet 250 PSI Lead-In Rubber Air Hose With 1/4-Inch MNPT Ends Now

This Goodyear hose is designed for connecting peripheral equipment such as hose reels to hard lines down line from the compressor. It is rubber and it's lifespan of years in operation will be greatly reduced if not used properly. This is a great hose and one of the best when used properly.

Connecting it directly to a compressor without a filter will allow oil and other sludge buildup to quickly occur in it which will soon begin to destroy it from the inside out, eventually causing a blister to form and rupture usually near one of its end fittings. Air compressors expel contaminates such as oil, moisture, and others from the air, that will destroy any rubber hose over time sometimes in only a short period of time. This is why a coalescing type filter should be used before any rubber air line. On smaller consumer grade compressors (even contractor grade portable compressors), it doesn't take a very large or expensive filter to greatly increase the life of connected rubber hoses and a filter will help prevent contaminates such as water and compressor sludge from entering and damaging air tools. Prevention steps of these buildups should also be taken by draining the compressor tank and the filter frequently which will also greatly increase the life of the air tank and the filter.

An air cutoff valve and added pressure regulator should also be in the line before any rubber hose. The reason for this is all rubber hoses should be depressurized when not in use, and all air lines should be re-pressurized slowly. The added regulator also keep the line pressure steady and allows for setting the correct pressure for the tools being used. Following this procedure will make all air lines and tools last many years even decades! Using this inexpensive Goodyear hose properly can also aid in preventing a failure that could drastically reduce the life of the components of your air compressor and never leave an air compressor turned on when not in use.

What should you use to connect a stationary (or portable for a stationary use) air receiver (compressor) to stationary lines or piping? The answer is a flexible braided stainless wire hose designed for this. They cost more, but they cost less over a period of years in comparison of their lifespan to having not used a hose where and how it was designed to be used. Here's an Amazon link to one similar in size to this Goodyear hose New Flexible Metal Hose Connector 1/2" x 18" length air compressor stainless steel braided.

What prompted me to review this product were the user reviews and submitted photos in the photo gallery. Most notably, was one of a large vertical compressor using this Goodyear hose improperly a sure path to destructive failure with no filter present to protect the hose, regulator, or any tool and line, connected after that regulator. I like equipment to last as long as possible, and using it properly is how you can keep it looking good and in service as long as possible. I have a smaller two stage 3 horsepower compressor I recently replaced the air receiver to after over 30 years of use. The whole unit still looked new after all the years of use, and the compressor runs like new after replacing the old original non-ASME tank that had begun to leak. I have since moved that compressor to the garage on my home, and installed a new 7.5 HP Emax in the garage behind my home. Proper use means less upkeep and less expense over time.

The Goodyear "yellow" 300 PSI hoses are all great products, just use them correctly and they will prove their superiority to you over any test of time. This 1/2" hose comes with well made 1/2" male NPT brass ends and can, and will last well beyond the Goodyear 10 year limited warranty it carries. I have a number of them in use that are well past the warranty, and they still look new and perform excellent.

Read Best Reviews of GOODYEAR 46512 3/8-Inch by 10-Feet 250 PSI Lead-In Rubber Air Hose With 1/4-Inch MNPT Ends Here

I bought this to run from my compressor to a wall mounted regulator/water filter. Made in USA of high quality materials. Looks like it will last a long time.

Want GOODYEAR 46512 3/8-Inch by 10-Feet 250 PSI Lead-In Rubber Air Hose With 1/4-Inch MNPT Ends Discount?

Aftrr finding lead in hoses at both HD and Lowes selling for $19 plus I thought I would give this a try. It is professional grade.

Save 45% Off

I needed a short length to go from the compressor to the hose reel I mounted to the wall above the compressor. Worked well.

Stanley Bostitch Air Compressor Replacement PRESSURE REDUCER #AB-9051116

• Genuine OEM Replacement Part #AB-9051116
• Compatible with Stanley Bostitch Compressors.
• What's included : (1) Replacement Stanley Bostitch Air Compressor Replacement PRESSURE REDUCER #AB-9051116
• New, bulk packaged
• Please refer to list below for compatibility

i have a husky air compressor that is about 2 years old the reducer broke and i was looking for a brand new air compressor.. i found this replacement and it has worked perfet i just unscrewed the silver part of it and left the air tubes still intact and screwed it right in in like 10 min...saved me about 200 bucks..

GoodYear 047 1/2-Inch x 50-Foot Rubber Industrial Hose - Red

• 1/2 inch x 50 feet, 200PSI
• Oil-resistant
• Can be used in all temperatures
• Includes male brass ferrules and barbed fittings
• Made in USA

As the previous review stated, this hose is overkill for everyday applications, such as connecting air nailers, sanders and such to the source. I use this hose to move large volumes of air from my compressor to my regulator on the jobsite to minimize pressure drop and supply the maximum amount of air to the multiple tools connected to the regulator. That being said, if you are only going to attach tools directly to a compressor, buy the 3/8" which is lighter weight, easier to manuver and less costly. Given the size, the hose is slightly heavy to attach to a framing nailer and a little cumbersome to wrap up at the end of the day.

UPDATE JULY 2010: Hose is still working great. No leaks. Now my oldest hose by far and used frequently.

Buy GoodYear 047 1/2-Inch x 50-Foot Rubber Industrial Hose - Red Now

This 50' hose is perfect for my purposes, and was priced well below what local retailers were asking. I was advised to stay away from "no-name" brands, and this hose carries the GoodYear name at a great price.

Read Best Reviews of GoodYear 047 1/2-Inch x 50-Foot Rubber Industrial Hose - Red Here

Great hose as reviewed by others.

It has 3/8" threads which is not mentioned.

I thought it would have 1/2 inch threads but

still fine for my usage.

Want GoodYear 047 1/2-Inch x 50-Foot Rubber Industrial Hose - Red Discount?

I should have read the reviews, it would have saved me a lot of trouble. I didnt know that the ends are 3/8 and not 1/2" I ordered all of my fittings for that size and now I cant use them. my mistake but it should have something in description.

Save 2% Off

It flexes and stretches, but never kinks or breaks. It is a good hose and I am very pleased with it.

Makita AC310H 2.5HP High-Pressure Air Compressor

• Makita high pressure compressor technology delivers 400 PSI capacity for the next generation of high pressure nailers.
• Dual capacity: two universal couplers for conventional nailers (3.6 CFM at 90 PSI) and two couplers for high pressure nailers (2.7 CFM at 300 PSI).
• Low amp draw reduces incidences of tripped breakers and voltage drop during start-ups.
• Efficient dual-head (2 stage) pump provides faster recovery time and improved performance.
• 1,720 RPM enables greater displacement at lower RPM and lower noise.

First I want to say that Amazon was stellar to work with in every regard. The compressor arrived incredibly quickly, as promised, and customer support was very focused in their attention to customer satisfaction and follow through.

As to Makita, my first impression was the cheap and poor job in their packaging of this heavy and comparatively expensive item. I was surprised at their indifference and lack of care in protecting their product. It displayed a definite lack of pride.

I attempted extensive research before purchasing this compressor but Makita's poorly drafted owner's manual, available online information and Makita's technical support left a lot to be desired. This compressor was not available locally so it was also not possible to evaluate one firsthand.

The options for a 400 PSI high-pressure portable compressor are few, so I decided to go with the Makita AC310H, relying on the fact that Makita is a well established company with a past reputation for decent quality power tools.

Regarding the design of the compressor, it appears that those responsible for its conception seem to have actually cared about their work, unfortunately however, they obviously were not able to oversee the production, quality control and packaging of it.

The initial appearance was actually impressive, but on closer inspection the lack of care in assembly is evident, from oversized wrenches rounding the corners, to some low quality components incorporated, to the failure of properly assembling the high-pressure regulator, to the unexplainable gouging and scratching on the bottom of the air tank.

Upon switching the compressor on it immediately failed to build higher pressures because of the aforementioned regulator. It was impossible to get to the regulator without disassembly of components so further reviewing could not be concluded. It was expeditiously returned into the confines of it's cheap cardboard box and was summarily sent packing. Kind of a shame as it really wasn't its fault.

It seems to me that the bean counters took a good design and then farmed it out to the lowest common manufacturing denominators in China with the sole intent of maximizing corporate profits, hence increasing their bonuses at the expense of their customers.

The Makita name on something now leaves me with an one star impression, and this buyer will be bypassing it in future tool prospects.

Buy Makita AC310H 2.5HP High-Pressure Air Compressor Now

Cheap regulator for such an expensive compressor. The high pressure regulator failed during testing the compressor for the first time out of the box. I received a new regulator under warrantee. I disassembled the old regulator to find out what happened. The threaded shaft for adjusting the pressure is made of steel with very fine thread. The nut that it runs through is made of soft brass. The threads in the brass are striped clean through. Because of the inferior materials used I can foresee this happening again and again.

Read Best Reviews of Makita AC310H 2.5HP High-Pressure Air Compressor Here

I bought this air compressor hoping to replace a makita MAC2400 that I had. I did not have a specific use for the high pressure system, but I liked the idea of high pressure for the future. I dont believe this compressor makes air as fast as my old one. If they had two hot dog tanks on it, I think it would be and awesome machine. But it doesn't catch up on air vary fast. It does run quiet and doesn't draw a lot of power. I think I will go back to my old compressor for my next purchase.

Want Makita AC310H 2.5HP High-Pressure Air Compressor Discount?

Makita AC310H 2.5HP High-Pressure Air CompressorMakita AC310H 2.5HP High-Pressure Air CompressorThe Makita AC310H 2.5HP High-Pressure Air Compressor I bought it from Amazon.com, it failed right out of the box, just like the rest of the reviews said, it leaked everywhere, never built pressure to 400, ran constantly, only got to 300 psi, the HP guns shoot at 320. It leaked when running from the head area, but when off no leaks, it's a failure of design passed off to USA. The Max high pressure, the compressors work well, light too, when the $1,400.00 to 1,500.00 item quits you'll not find a repairman or customer service, around, My 2 came back after a year in parts in a box saying a new one was cheaper than fixing either of the two (2) so $1,500.00 throw away compressors, get used to it. I'll be selling all six guns, but with a conscience, should I cheat someone? Or should I take my pleasure out with a sledge hammer, or a hood ornament for an Eitsil (Fords failure)It was pretty cost effective when using the concrete nailer less than half the cost of the Hilti, ramset, but factoring in the throw away compressor cost, and time dealing with a non-repairable item, as the Makita too. Buyer Beware run, don't walk, away from these items, it's a puzzle designed to beat you. The Makita AC310H 2.5HP High-Pressure Air Compressor is a hood Ornament for a junker. Amazon should not push this item, it's disappointing at least.

Save 47% Off

I'm a GC, and I bought the makita HP compressor & framing nailer two years ago. At the time there were no reviews here, and only a brief write up on some tool review website. I bought it because Im a bit of a tool junkie, and getting a new toy makes framing walls seem like more fun. Anyway, I figured I'd throw in my brief thoughts after reading all the negative reviews.

Mine works great, I love how quiet it is, how quiet the gun is, and oddly enough I love the makita hose more than anything else.

The gun is crazy light. Use it for a week then pick up a regular coil framing gun full of 3" spikes. This could be an exaggeration but it feels 5lbs lighter.

The compressor however is NOT crazy light. It's all motor, which I suspect is made of some tungsten lead super alloy. I move it around at night or other lowlight conditions, so nobody sees me struggling to tote this small compressor.

Full disclosureI've probably used this thing a total of 80 hrs. It's too nice for my guys to mangle, so it's locked up in my private tool section where the gremlins can't get to it.

All in all, it's a novelty to me. It's cool, looks sweet and is fun to use. I've never used it for anything that a regular gun and compressor couldn't have done. If you've got money to "waste" maybe you'll like it too.