Hitachi EC119SA 15 amp 2.5-Horsepower 4-Gallon Twin-Stack Air Compressor

• Quiet operation and extended life
• Powerful 15 amp-induction motor
• Protective roll cage design protects the pump and motor from damage
• Includes 2-inchdustrial couplers, oil dipstick, and 8-ounce synthetic oil
• 1-year limited warranty
• (2) factory installed couplers
• Cast iron, oil lubricated pump with oversized bearings for quiet, dependable service
• Comes with a 1-year limited warranty
• Contractor preferred 4-gallon twin stack tank
• Powerful induction motor

I purchased one of these units and was very pleased for about 3 months. The unit ran great and was very quiet for a compressor due to the induction motor. Running it indoors you can actually talk over top when its running and hear the other person. At 3 months the unit stopped working and would only hum without kicking on. After replacing with a new unit I was ok for about 3 weeks and the same problem happened. The issue is the oil level. Hitachi supplies a small bottle of 5w-50 oil and the instructions are to fill on a level surface to a point between the notch on the dip stick. The first time I over filled slightly using about 4/5 of the oil supplied. on the second unit I filled to the required level or about 2/3 of the oil supplied. Both units eventually seized. After speaking with a customer service I found out the supplied oil is premeasured and ALL THE OIL SHOULD BE ADDED. I found Hitachi to have very good customer service, the first unit was replaced and the second serviced at no cost. My opinion is this is a very good unit with a small design flaw on the oil pickup system and instructions which should tell you to add all the oil. Also note, when they say don't operate at more than 10 degrees angle, they mean it. The oil will not get to the crank and the unit will seize. This unit is very small, very portable, extremely quiet unit and supplies 4.cfm @ 90psi all of which is a great combination. I would have given 5 stars except for the lost time and effort of not properly addressing the oil issue for this unit. At the end of the day I purchased a dewalt D55146 oil free unit for a backup as jobsite reliability is key for me. I hope the Dewalt performs better over the long run.

Buy Hitachi EC119SA 15 amp 2.5-Horsepower 4-Gallon Twin-Stack Air Compressor Now

I ordered this compressor and was excited to recieve it. UPS does it again. The release valve was snapped off. I will give a full review when I talk to Hitachi and get a new one.

Update: Had to pay a machinest to tap out the broken value. Hitachi customer service was awesome and sent me the replacement parts for free but now the compressor is leaking at the plastic hose that uses a preasure fitting to hold it in. I buy a lot of tools and never have had an issue. I would not take my experience as a negetive. Hitachi is great I just got a lemon.

Read Best Reviews of Hitachi EC119SA 15 amp 2.5-Horsepower 4-Gallon Twin-Stack Air Compressor Here

This is the first air compressor that I've purchased, although I've used them on-and-off for years. After a lot of research, I concluded that the quality level of unit that I wanted, I could not afford. There is a significant jump in build/design quality when you go from the $125/$300 range to the $300/$500 range. I need one only for home remodeling/garage use, but I didn't want to buy junk. When I found this unit factory reconditioned, I bought one immediately. After 1 week of use, I am very happy with my decision. It is well made, easy to use, fairly quiet, has a very low tank fill time and recovery time, and is a notch above homeowner-grade tools. The unit isn't light, about 65 lbs, but that's due to the liberal use of metals instead of plastics. It arrived in almost like-new condition. It looks as though is was only used once or twice, then returned. You can download the manuals that originally came with it from Hitachi's website. Highly recommended.

Want Hitachi EC119SA 15 amp 2.5-Horsepower 4-Gallon Twin-Stack Air Compressor Discount?

Owned this air compressor for 1 year. Used it to frame and sheath a house, sheath and shingle three roofs and trimming out two complete interiors.

My experience is as follows;

Framing

Compressor kept up with two Hitachi NR90AE framing nailers providing the nailers were not used in "bump" mode for several consecutive shots.

Barely able to keep up with one Hitachi NR90AE framing nailer in "bump" mode firing several consecutive shots.

Completely unable to keep up running two Hitachi NR90AE framing nailers in "bump" mode firing several consecutive shots.

Sheathing

Compressor kept up with two Hitachi NV83A3 coil nailers providing the nailers were not used in "bump" mode for several consecutive shots.

Barely able to keep up with one Hitachi NV83A3 coil nailer in "bump" mode firing several consecutive shots.

Completely unable to keep up running two Hitachi NV83A3 coil nailers in "bump" mode firing several consecutive shots.

Roofing (Shingles)

Compressor kept up running one Hitachi NV45AB roofing nailer applying five nails per shingle.

At times would not keep running two Hitachi NV45AB nailers applying five nails per single without waiting approx 45 seconds to fully recharge.

Trimming

Compressor kept up running two MT65A4 finish nailers or two NT50AE2 finish nailers.

I recently purchased a second Hitachi EC119SA for back-up and will run two compressors when "bump" nailing the large framing and coil nailers.

The compressor must operate on a dedicated 15 amp circuit or 20 amp circuit. Due to the oil lubricated pump the compressor can not operate on more then a 10 degree angle.

I have not used the compressor in temperatures below 48 degrees so I can not comment on the reported poor cold starts. I do know other name brand oil lubricated compressors also experience poor cold starts.

So far for the money I had good luck running these compressors!

Save 60% Off

I have had this unit for a couple years, with only occasional use filling tires, blowing sawdust out of chainsaws, etc. MAYBE 10 or 12 hours of total continuous run time. Recently the pressure reducer/regulator control failed I have rarely made changes to the delivered pressure, so I think the part was just defective from the beginning. As others have noted, in cold weather the unit does not start up easilyeither trips it's internal breaker or the house breaker. It can take some time playing with it to get it going. In warmer temps this is not a problem.

(Over a year later...) I have run the compressor a lot since I changed out the reducer/regulator, and it has been a good performer since then.

Porter-Cable FN250B 3/4-Inch to 2-1/2-Inch 16-Gauge Finish Nailer

I have three Porter Cable finish nailers, the 18 gauge brad nailer, the 16 gauge finish nailer, and the 15 gauge angle finish nailer.

Excuse me for stating the obvious, but the 18 gauge leaves the tiniest hole, which is nice for clear finish work. The 16 gauges hole is a bit larger, but still acceptable for clear finishes on larger trim work. The new 15 gauge, actually leaves a D Shaped hole. It is kind of large, and is designed for putty and paint. The 15 gauge is a bear though. When you fire it for the first time, POW, you know it is stronger than the 16. Although I haven't had any unusual problems with the depth drives on the 16, other than knot concerns.

If I had to choose one nailer, instead of all three, I would say this 16 gauge would give you the most universal use.

This 16 gauge, has great ergonomics, fires reliably, (keep your finger off of the trigger when plunging the nose) and overall does a very nice job. Keep it oiled.

I wanted a finish nailer that could make my nailing job easier

as I suffer from Carpal Tunal Syndrome. I conducted research on the reliability, price and features on several different finish nailers. I spoke to trades people and co-workers who had Porter Cable tools, and came away impressed. This was my first Porter Cable Tool and air nailer purchase.

What impresses me most about the FN250B air nailer is the balanced feel and weight of this tool along with the padded handle. The nailer loads easily and has never jammed. Adjusting the depth of the nails is simple.

I use the FN250B finish nailer on home improvement projects like crown molding installation and building custom shelving. I wonder why I didn't buy one years ago.

Buy Porter-Cable FN250B 3/4-Inch to 2-1/2-Inch 16-Gauge Finish Nailer Now

I purchased this nailer to replace the ceiling in a 100 year old farm house. No previous experience with nailers or remodeling for that matter so I checked the reviews, then went for the best deal. I played with it for a day in scrap wood to learn how to adjust the depth of fire and get the feeling of how it worked. It never double fired, jammed, or misfired, worked well upside down and was light enough to keep above your head for multiple nailings and I never got fatigued. My girlfriend even used it without a problem and thought it was very easy to use. It is not intended for tight spots though so the corners were tricky. I oiled it per manufacturers suggestion and it worked without a hitch. Get the angled one if you are going to do a lot of moulding work or have tight spaces. I would highly recommend this product

Read Best Reviews of Porter-Cable FN250B 3/4-Inch to 2-1/2-Inch 16-Gauge Finish Nailer Here

I love the power of this gun. It drives nails with a forceful, and solid hit. I've used the Senco "Finish32" guns from home depot that shoot these same 16 gauge nails and this Porter Cable gun by far out delivers that model 10/1. I'm in the field everyday with this unit running all types of trim with it.

Keep your air to 120 and forget setting nails with this light weight, powerful tool.

Enjoy!

Want Porter-Cable FN250B 3/4-Inch to 2-1/2-Inch 16-Gauge Finish Nailer Discount?

I have been searching for a light weight, general purpose finish nailer for a while. Finding the FN250B was well worth the wait. A beautiful design with a secure, comfortable grip and a much appreciated, adjustable exhaust port. Reloading or changing nail lengths couldn't be easier. I have used this nailer for nearly a month and it has failed to jam even once ... knock on wood. After working with this newly designed nailer, I will definitely consider PC products when making future purchases.

Solo® 457V Hand-held Sprayer 3 Gal

Bought this specific sprayer so I can use air compressor to pressurize it. Top nipple of pressure relief valve broke off first time sprayer used which makes releasing pressure manually very difficult. Metal rings for strap broke when filled sprayer picked up first time. Sprayer works OK otherwise.

1/4 In Ball Swivel Connector ARO Interchange

This little swivel connector works perfectly and makes a surprisingly big difference when working with air tools, whether a blow gun or pneumatic nail gun.

Save 30% Off

JET JAR-338 3/8-Inch NPT Air Regulator

• 3/8-Inch connection port
• Air pressure can be maintained by the steeples regulator accurately over a wide range of flows as necessary for each application
• Easy to read indicator
• Full 1 year warranty

I was delightfully impressed with the regulator. I needed a decent regulator at a good price, this fits the bill perfectly. Works without a hitch, no leaks and it is easy to adjust and lock into place. I would recommend this regulator to others.

Buy JET JAR-338 3/8-Inch NPT Air Regulator Now

ordered to replace a pressure regulator on a porter cable compressor The jet regulator appears to be a lot better constructed than the porter cable regulator and has functioned well with my compressor. The porter cable regulator was much inferior to the jet regulator.

Read Best Reviews of JET JAR-338 3/8-Inch NPT Air Regulator Here

Arrived expeditiously. Product is exactly as advertised. Assembly was intuative and easy. Product works great with accuarate yet easy adjustment. Adjustment knob lock keeps the curious at bay.

Ampro A1440 Air Regulator with Gauge, 0-160PSI

• Includes a 0-160 PSI pressure gauge
• Provides fine air control for spray gun and air tools
• Regulate constant level of air pressure

The description for this product does not state the actual operating characteristics. It only says (several times) that it has a 0 160 psi gauge. You would think the gauge scale would be the same as the regulator characteristics, but this is not true. The label on the product says, "Max. Pressure 100 PSI Adjustable range 7.1 PSI -92.3 PSI" I assume the only reason it has a gauge that goes to 160 is to fool people into thinking the operating range is higher. (By the way, the dial background really is white, not green. I am not sure why this matters, however.)

Buy Ampro A1440 Air Regulator with Gauge, 0-160PSI Now

I purchased this gauge to use with my multiple spray guns and brad nailer. I used quick connect couplers on both ends to make it easier to use with any tool. Very pleased with its performance. Holds pressure at exactly what I set it for. This is a real regulator and not.just a reducing valve. Highly recommend.

Read Best Reviews of Ampro A1440 Air Regulator with Gauge, 0-160PSI Here

I specifically ordered this product because it has a green gauge face in the product picture (prior to and June 1st, 2012). When the item arrived the product had a white gauge face, which I do not want.

Want Ampro A1440 Air Regulator with Gauge, 0-160PSI Discount?

I never used this item but found when I received it that it was designed with a swivel fitting most likely specifically for a spray gun attachment.

Stanley Bostitch MIIIFN 1-1/2- to 2-Inch Pneumatic Flooring Nailer

• 1-1/2-inch to 2-inch pneumatic flooring nailer for driving L-shaped flooring cleats
• High-speed; extra-wide composite base; high-capacity magazine; 420 inch-pounds of driving power
• Constructed of aircraft-grade aluminum
• Includes rubber-tipped mallet
• 17-1/4 by 3-1/8 by 11-1/2; 11.2 pounds; 7-year limited warranty

I'm a small volume custom home builder with a crew of five. We install the hardwood flooring on most of our jobs. We have used a manual powernailer for years. Recently I purchased Bostitch's MIIIFN floor nailer and now have moved our manual nailer to the back of the tool bin. Just a light tap is all that is required to fire the nail. In the event the board is slightly bowed feel free to swing away and hammer the board in place. This tool is easy on my carpal tunnel and for those who aren't ambidexterious it's a snap to use with either hand. It does take some time getting used to dragging the air hose around with you, and you definitely need ear protection. But the benefits far outweigh these nuisances.

Buy Stanley Bostitch MIIIFN 1-1/2- to 2-Inch Pneumatic Flooring Nailer Now

I had a difficult time deciding which nailer to buy. Should I get the 2" stapler or one of the many cleat nailers out there? I called my hardwood flooring company (BR-111) and was advise that they do not recomend the flooring stapler as the tongues may break while stapling. I ordered the Bostitch floor cleat nailer to install my solid Brazilian Cherry Hardwood flooring. I found out that Brazilian Cherry is the 4th hardest hardwoods availabe. Brazilian walnut is the hardest. I also found out that Brazilian Cherry is almost double as hard as the hardest american oaks. I received my nailer and started nailing down the floor. I set my compressor at 85 psi and nevet touched it again. I installed almost 700 feet of hardwood and the nailer worked perfect. I love my nailer but have to mention that with its size you have to face nail everything within 8" from the wall as the tool is to wide to actuate the striking mechanism. All-in-all this is the tool to buy if you have any doubts. Buy the nails from home depot as their about $7.00 cheaper that online.

Read Best Reviews of Stanley Bostitch MIIIFN 1-1/2- to 2-Inch Pneumatic Flooring Nailer Here

I was able to install 160 square feet of a 900 square foot flooring job before my nailer broke. Stanley considers this broken part "normal wear", and Amazon will not take back opened merchandise. Just a heads up to contractors who may worry about buying tools onlinedon't do it. My regular supplier would have given me a new nailer no questions asked.

Want Stanley Bostitch MIIIFN 1-1/2- to 2-Inch Pneumatic Flooring Nailer Discount?

We bought this nailer to install 1800sqft of hardwoods in our house. Here's our experience:

Pros:

Beefy. You can tell it's made for the pros. And you can smack it hard to help get warped boards tight.

It does exactly what it's supposed to.

The included mallet feels like high quality, and its just the right weight.

Cons:

We had a lot of problems with the nailer allowing the last nail in a stack to fall out of the nailer. This is a problem because it can fall half way out, then when you put the nailer down on the finished floor, it's easy for the sharp nail to scratch the finish. Get in the habit of setting the nailer on the unfinished part of the floor.

The nailer includes a plastic shoe that bolts to the underside. The instructions say this is for finished floors whereas the normal plate is for unfinished (site finished) floors. The shoe was useless for us. It made it nearly impossible to line up the nailer with the tongue. The normal plate didn't scratch the floor at all. So we used it that way. Maybe softer woods would have scratched (we used distressed oak).

Having to attach the handle was annoying. It also seems like a clunky afterthought. But once installed, it worked fine.

If you don't smack it with a hammer hard enough, it won't drive the nail in all the way in. If it's half way out, you can use channel lock pliers to pry the nail out. But if you get it 90% of the way in, you'll have to use a nail set to drive the nail in the rest of the way so that the next board fits. This is a real pain. The nail metal is soft. It likes to deform or break off. This is more operator error than anything else. So smack it hard.

How it could be better:

Stop letting the last nail fall out.

Make the nail cartridge slightly longer so you can put the next stack of nails in sooner.

Redesign the handle.

What we learned:

For wood floors, wider is better. 5" wide boards mean half the cutting, fitting, and nailing compared to 2.5" wide boards.

Also pick up a finish nailer to help when you're close to walls. If you take the rubber guard off, a finish nailer can nail through the tongue just like this nailer. Less face nailing.

Save 57% Off

Being an owner & user of Bostitch air tools for 15+ years, my expectations were high when I ordered this tool. Once again, Bostitch has not let me down. This tool is great, easy to use and will undoubtly last a long time. I would reccomend purchasing the finished flooring foot if you are going to use this tool on pre-finished flooring.

Stanley Bostitch PN50 Mini Impact Nailer

• Rubber grip designed to insulate and reduce vibration
• Weighs only 1 lb.
• 360° swivel air fitting for maximum accessibility
• Front exhaust directs air away from users palm
• Drives most common bulk finish, framing & timber nails

I giggled the first time I used this, it drives nails with such ease as if the wood was butter.

It's great for metal fasteners and tight spaces, it gets into all the small corners where neither a full size nail gun nor a hammer would fit.

The small size is a perfect fit for my (large) hand, and squeezes into smaller places than the larger model palm nailer.

The magnet holds the nails well so you can drive them with one hand, just press and the nail is quickly hammered (vibrated?) into place.

You can stop early and leave the nail head up if you're just tacking things, or come back later and finish the nail flush.

Buy Stanley Bostitch PN50 Mini Impact Nailer Now

This is another product that I give 5 stars, not because it is the best on the market (not industrial quality) but is a good deal for the low price. I had a project where I needed to drive 240 nails in tight, overhead areas could have done it with a hammer but my wrist and shoulder hurt just thinking about the prospect.

Had this puppy in a couple days with Amazon Prime, quickly reviewed the instructions and 45 minutes later had the job done didn't even break a sweat.

Will probably submit a video of this in action because you have to see it to believe how easy it makes a job like this.

One word of caution, read the instructions about how to insert the nails. It's pretty easy to accidentally "fire" this thing if you are not focused every time you load a nail and I imagine even a preacher would have some choice words if it fired with his/her finger over the nail point.

Read Best Reviews of Stanley Bostitch PN50 Mini Impact Nailer Here

I was very impressed with both the size and the power. Was able to sink a 3.5" spiral shanked nail with ease. The only disappointment is that the nail opening is rather narrow. The majority of common framing nails will fit, but if you try something with a bit larger head, it won't. Forget Roofing nails! This is the only palm nailer I've used, so I don't know how the opening compares to other brands/models. The speed of this nailer does not come close to a good nail gun, and the fatigue factor will be a lot higher. So it's great tool for tight places, and small to moderate volumes of nails, but if you are doing a large project, you might want to consider a stick nailer (preferable in addition to this nailer).

Want Stanley Bostitch PN50 Mini Impact Nailer Discount?

This thing is too fine! When a hammer or nail gun won't get to the nail, this will. I just used it to install an electric box in an 8" stud space in a corner with a wall that prevented any kind of hammer or even a screwdriver from working. It's simply amazing. All of this comes from a guy who has been doing this kind of work for 40 years and who owns a gas powered nail gun, air powered nail guns and all kinds of hammers.

You may not use this baby every day but when you do have a need, nothing else will get the job done.

Did I mention that it's very ergonomic in its shape?

Buy one and don't look back!

Save 15% Off

This is a perfect little nailer that does the job with any size nail. I've shot joist hanger nails up to 16d common any they go in very fast.I am extremely pleased with this nailer.