Stanley Bostitch CAP1512-OF 1.2 Gallon Oil-Free High-Output Trim Compressor

• High-output oil-free pump delivers 2.8 CFM @ 90 PSI and 150 PSI max operating pressure for multiple finish tool operation
• 2.0 HP (Peak), 1.5 HP (Running) motor draws 12 amps for easy start up without tripping circuit breakers
• 1.2 gallon compact design weighs 23.5 lbs. for easy portability
• Integrated control panel with roll cage protects gauges from jobsite damage
• LED ON/OFF switch lets you know when the compressor is on to eliminate low-pressure misfires

Here are a few measurements comparing this Bostitch to the Porter Cable 6 gallon pancake compressor it's replacing:

Bostitch / Porter Cable

Time to charge: 0:47 (@150 psi) / 2:31 (@135 psi)

Decibels @ 3ft: 90 dB / 92 dB

Weight: 26.8 lbs / 33.8 lbs

Air blower @ 90 psi (time before pressure falls below 90 psi): 9 seconds / 11 seconds

Pressure after 1 minute of air blower: 35 psi / 50 psi

Equilibrium pressure leaving air blower open: 35 psi after 30 seconds / 35 psi after 2 minutes

The Bostitch is faster to charge, quieter, and lighter. Both motors produce about the same amount of compressed air.

The smaller tank on the Bostitch provides slightly less air, but the fast recovery mostly offsets this concern.

The Bostitch earns five stars from me.

Buy Stanley Bostitch CAP1512-OF 1.2 Gallon Oil-Free High-Output Trim Compressor Now

I purchased the Bostitch CAP1512 compressor due to its light weight and compact size. I wanted an alternative to my 70 lb. Dewalt/Emglo (which works perfectly, but without wheels is too cumbersome to carry around). The Bostitch worked right out of the box. It was easy to set up and use. I used it to with my brad nailer to install the shoe moulding in my recently remodeled kitchen and it worked flawlessly.

Likes: compact size, portability, on/off switch, air pressure, price, control panel, ease of use

Dislikes: none noted

I am satisfied with the compressor and would reccommend it to others who are in the market for a compact compressor.

Read Best Reviews of Stanley Bostitch CAP1512-OF 1.2 Gallon Oil-Free High-Output Trim Compressor Here

I use a compressor for brad and finish nailing, inflating tires, and blowing sawdust off my tools (I also energize some effects at a haunted house at Halloween, but that's another story). One of my main uses is to trim out sets at a local community theater, so easy portability is a must. This compressor fits the bill perfectly.

The 1.2 gallon tank is small, but the fact that it goes to 150 PSI means it performs like a larger tank, and it also means that 100 PSI tools will always be operating at full pressure. Also, the pump is fast and fairly quiet as these things go. It takes 45 seconds to charge from 0 to 150 PSI. The pump cuts back in 125 PSI and takes 10 seconds to charge back up. This is enough to get about 5 shots out of my 16 gauge finish nailer, and of course I could get at least twice that before the tool actually lost pressure. I don't have a framing nailer, but I'd guess you'd get about half that, so it would work in a pinch, but you wouldn't use it for serious jobs. It will run the blower attachment flat out at 50 PSI.

I'm replacing a 4 gallon pancake compressor that was a bit heavy and awkward to carry. This compressor is light and the handle is well positioned. Also, all the plumbing is well protected, which was another issue with my old compressor, which had pipes and gauges sticking out just asking to get knocked off.

Finally, since my old compressor once tipped over and dumped oil all over my car, I *really* appreciate the Oil-free, no maintenance motor.

Most low end compressors have visibly shoddy construction, but this at least appears well built. Of course, only time will tell how it actually holds up.

So, bottom line: obviously, this isn't for serious framing, roofing, paint sprayers, or air sanders, but for trimming and other light duty, where portability is important, it's absolutely perfect.

Want Stanley Bostitch CAP1512-OF 1.2 Gallon Oil-Free High-Output Trim Compressor Discount?

I really like the ergonomics of this air compressor. The dials are large and easy to read. All of the controls are on the front of the unit. This compressor is very light weight, making it extremely portable. I am amazed at how quiet this compressor is, and the tank fills quickly reducing the run time of the engine.

So far, I've only used this compressor to fill the air in the tires of my SUV, motorcycle, lawnmower and bicycle. No more trips to the gas station I should have made this purchase a lot sooner. I can say without hesitation that you will be delighted with this air compressor from Bostitch.

Save 13% Off

I bought this because it is the lightest and smallest compressor that fit my needs. I primarily use it with finish guns and staplers and it works exceedingly well. I don't know how long it will last but I think for the price and what I have already been able to complete it has paid for itself. Great design. I highly recommend this for small jobs.

CW211400AV Campbell Hausfeld Pressure Switch 120/150

• Campbell Hausfeld Pressure Switch
• Fits Campbell Hausfeld, Husky, Sears plus others

Excellent timeliness in delivery! The switch is exactly what I ordered and needed for the air compressor. It has been working flawlessly and am glad I could locate it quickly.

Buy CW211400AV Campbell Hausfeld Pressure Switch 120/150 Now

This is adequait and somewhat easy to install by owner. The tank gathers some mositure then "rust" that contaminates the switch

Read Best Reviews of CW211400AV Campbell Hausfeld Pressure Switch 120/150 Here

The Campbell Hausfeld Pressure Switch 120/150 was necessary to repair our compressor. This was the best place to order as it was easy and was shipped promptly.

Eastwood Air Compressor Water Moisture Separator Filter

The product arrived before expected. The unit is well made and works great to remove the moisture from my air compressor that I use for my material blasting cabinet. Without the separator I had problems with the blasting material clogging the nozzle. With the separator in line the nozzle remains clear and I can blast as long as I need without having to disassemble the nozzle to clean the debris. The filter material is easy to remove and clean and/or replace.

I recommend this product.

Stanley Bostitch SB-1664FN 16 Gauge Straight Finish Nailer

• 16-gauge straight finish nailer ideal for Interior/exterior finish and trim; furniture; cabinet work; and staircases
• Adjustable depth guide sets nails to desired depths quickly; quick-release nose door for fast jam clearing
• Features ergonomic comfort grip
• Kit includes finish nailer; 2-inch finish nails (1,000-pack); oil; convenient carrying case
• Weighs just 4-pounds; 7-year warranty

I already owned a Porter-Cable 16 GA. finish nailer, and we were starting a job to hang about 1500 square feet of boxcar siding in a rustic cabin. All I really wanted was another finish nailer that would shoot the same nails as my Porter-Cable. We use the Bostitch more than the original gun nowadays. It seems to drive the nails just a little deeper.

Buy Stanley Bostitch SB-1664FN 16 Gauge Straight Finish Nailer Now

I had given good results to this gun in an earlier review. It does fire very well when it works.

Mine stopped firing over the winter. Yesterday I called Bostitch to order an o-ring kit. It is not available. You must purchase o-rings individually. There are over a dozen o-rings in this gun.

I then decided to disassemble the gun and troubleshoot the problem. Everything looked good until I took the trigger switch apart. An internal ring had lots of slp in it and did not appear to seal as it should. I was able to buy an o-ring from my lumer yard for $.20 and it fixed the problem.

The gun fires as it did when I first purchased it.

Beware.......it will cost a minimum of... for a repair center to check this tool and then they will also have to order individual o-rings for it. Maybe Bostitch can fix this soon.

Read Best Reviews of Stanley Bostitch SB-1664FN 16 Gauge Straight Finish Nailer Here

Back in October 2002, I wrote a review concerning the incident I had with the part #06 blowing out on the nail gun. This is the main Butt cap on the end of the nailer. As I stated in my review, I was not sure if it was a manufacturing error or just a fluke. After extensive research and contacting many people using the nail gun, I had reached the conclusion that it was indeed a fluke. Today, March 23rd, A design engineer from Bostitch contacted me. It seems that they have been trying to reach me for several months and finally caught me at home. They had been informed of my problem with this nail gun and were extremely concerned. As per our telephone conversation, they have sold hundreds of thousands of these units and this was the first time they had heard of this incident concerning the end cap exploding from the back of the gun. As I told him, I had come to the conclusion that this was a fluke and I did not feel that it was a design flaw. I also apologized to him for not posting a follow up concerning my conclusion that it was a fluke. This I am doing now. IT WAS A FLUKE FOLKS. I have the big brother to this gun and have used it extremely hard and it is working fine with NO problems what-so-ever. I only wish I had kept the exploded gun so I could send it back to them for analysis. By the way, they are sending me a replacement nail gun free of charge. This I am happy about because I really liked that little gun. Handy, Light weight, easy to operate and I could see my nail supply in the slide loader. Most other guns don't have a view window. Anyway, Kudo's to Bostitch. Thanks for the followup. Much appreciated...

Want Stanley Bostitch SB-1664FN 16 Gauge Straight Finish Nailer Discount?

This is an excellent nailer, maybe the best on the market. Little or no recoil, no jams and the performance is excellent. Loading is a breeze and the lightweight housing is nothing less than a dream when working in tight places. Cannot imagine a better nailer and the people at Amazon were right on with their delivery times. Thanx Amazon and Bostich!

(using wife's profile)

Pro finish carpenter, used this gun hard for 5+ years. Shot thousands upon thousands of nails through it. Had to disassemble once because I dropped it and it started leaking air out nose, just had to re-seat some bushing/bumper and hasn't leaked for the 4 years since. A piece on the nail advancing spring wore out after 4 years and bostitch sent me one no charge next day air. Broke the piece that holds magazine (dropped again) and again bostitch got me the part right away no charge. I own two of these and really like them, I do own other brands as well (hitachi, porter cable, cadex, etc.)so I'm not just a bostitch nut. I have also used other brands of finish guns. Worked with a guy who used to buy the $300+ hitachi and senco and paslode guns and now buys the bostitch. You must (with any gun) tweak the driver blade before use: The blade itself is a hair too long and needs to be ground down about 1/16-3/32" and the shoulders need to be tapered furthur up or otherwise the driver blade will make a rectangular hole with wings instead of just a small rectangular hole. once you do that the driver blade makes a perfect impression exactly the size and shape of the head of the nail.

New 1/4" ASME Safety relief Valve 150 PSI American made

• 1/4" Safety Valve 138 SCFM - 150 PSI
• Free Shipping
• 51 mm Tall x 17.5 hex
• ASME Certified & stamped w/ UV & UB stamps

The relief valve on my compressor failed and I looked everywhere for a replacement. Thankfully Amazon.com had exactly what I needed at a reasonable price and with free shipping. Problem solved.

Save 50% Off

Senco PC0947/FP18KIT 18-Gauge Brad Nailer Compressor Combo Kit

• 18-gauge brad nailer and 1-gallon compressor combo kit
• Nailer: adjustable depth of drive, rear exhaust, easy-open latch, no-mar pad, low-load-indicator
• Compressor: 1 gallon; aluminum cylinder with steel sleeve; 20-pounds
• Includes nailer, 1/4-inch -by-25-foot hose, safety glasses, fittings, oil, 1,200 brad nails, wrenches, and manuals
• 1-year warranty on nailer; 90-day warranty on compressor

My wife purchased this combo package for me for my birthday this year (well, more like I bought it and thanked her for it). I have to say, I am impressed.

THE BRAD NAILER:

The gun is lightweight and small enough to get into tight spots, yet it appears to be very well built. The protective no-mar pad does not scratch prefinished moulding, and the side load magazine is convenient and easy to use. I shot about 200 2" brads while installing new 1/2" baseboards and 3/4" birch door trim in my bedroom. Every brad was countersunk to perfect depth, and I did not get a single jam. I ended up with very professional results and finished in 1/2 the time it would have taken me with the old hammer and finish nails.

THE COMPRESSOR:

The PC1010 will change the industry. For homeowners, hobby woodworkers, and customer service professionals in the cabinetry industry this is the perfect compressor. There is no need to lug around a 4 or 6 gallon compressor for a little brad nailer. You can easily carry the nailer, hose, and bread box sized compressor in one hand. From startup, this quiet, lightweight little workhorse takes about 2 minutes to pump up to 110 psi. I consistently got 10 shots before kick in, then another 40 seconds or so to recover. I nailed right through the recovery time, and never had to wait for the compressor to before driving any brads.

SHORTFALLS:

It is very difficult for me to find anything that I don't like about this one. However, rumor has it that Senco guns work best with Senco brads, and the local home improvement stores sell mostly PC and Bostich... so I will need to find another source. I would not recommend the PC1010 for anyone who wants to drive anything larger than 18ga brads, or run multiple air tools from a single compressor. Also the compressor is so new that Senco has very limited literature on it, but I would be willing to bet they will get this taken care of soon.

CUSTOMER SERVICE:

Some of the best customer service I have had the pleasure to work with. If you purchased from an authorized dealer, and you have any problems with your equipment, I recommend calling Senco directly.

Buy Senco PC0947/FP18KIT 18-Gauge Brad Nailer Compressor Combo Kit Now

I got this package for very light duty use woodworking shop projects and qtr-round molding on flooring. The nailer is a quality tool that sells for $120 everywhere so that makes the compressor only $75. I had a $15 coupon so the compressor was only $60 for me.

The compressor is so light that it is no problem carrying it. The tank pressure is 125 lbs and I set the tank outlet pressure to 90 lbs. It shoots about 10 brads before it cycles but you can keep shooting as it runs. I used 5/8" brads on molding on a shop project and 2" brads on floor qtr-round without a single problem. This sure saves time and doesn't mar the wood. It is pretty quiet and also looks good. Getting to small jobs and using this little tool is a pleasure. I will get an air blower tip for it; so far I'm satisfied.

Read Best Reviews of Senco PC0947/FP18KIT 18-Gauge Brad Nailer Compressor Combo Kit Here

I agree with the other reviewers who have given praise to this product. I felt the same way till mine broke after less than a months use.

Of course it was the compressor which broke, the part with the 90 day warranty. I did not catch that when I bought this.

Senco is a good company, but I think this little compressor is not quite up to the quality of their other products.

In my case it was the 1/4" copper tubing which brings the air to the tank that failed. It split where the tubing had been bent.

I have fixed it with some liquid steel, since I'm on a job with it, I'm hoping the repair lasts till I have time to replace to tubing.

I have used this to build two large bookcase and cabinet projects so far, and in doing so I have learned the compressors limitations. It does not do well

shooting two inch nails into MDF. It does not have the power to fully sink the nail into the material. I bought this combo for the light weight

of the compressor, so I guess there must be some compromises. This won't take the place of more powerful compressors,

but it is great for carrying to and from a job. I just hope I do not have problems with it in the future. I'm not sure I would

recommend this product, the 90 day warranty on the compressor is a big negative. especially since it seems to have some problems.

Want Senco PC0947/FP18KIT 18-Gauge Brad Nailer Compressor Combo Kit Discount?

I upgraded to this from a cheap little electric brad nailer that could not sink a 1" brad. This tool is light and has plenty of power. The compressor is small & quiet and has absolutely no problem keeping up with the nailer. I own an old 5 horse 220 v compressor but wanted something to use inside the house without running hundreds of feet of hose from the garage. This will fill my needs perfectly.

P.S. I shop online alot and would like to say that Amazon.com has the best customer service of any company I have dealt with.

Save 28% Off

I own several portable compressors, but hate to lug them around. So, I bought this one for installations of wood mantels and little odd and ends work (like attaching a piece of trim after the rest of the job is already done). The little compressor is lightweight and perfect for small jobs like these. On bigger jobs I still use one of my heavy duty compressors. So, that may be the problem some of the other reviewers are having. It's just not built for heavy duty work.

The gun on the other had was a disappointment. I already had a Senco XP 25 and prefer it. Still, it's a pretty good price for both pieces, so, no real complaints here. I've just set the newer one aside, for now.

Regarding the cheap 1/4 inch hose... pleeeease. Anyone with half a brain knows it's a cheap piece of krap, but will work fine for the occasional hobbiest. If you want a good hose, buy one.

Stanley Bostitch PN50 Mini Impact Nailer

• Rubber grip designed to insulate and reduce vibration
• Weighs only 1 lb.
• 360° swivel air fitting for maximum accessibility
• Front exhaust directs air away from users palm
• Drives most common bulk finish, framing & timber nails

I giggled the first time I used this, it drives nails with such ease as if the wood was butter.

It's great for metal fasteners and tight spaces, it gets into all the small corners where neither a full size nail gun nor a hammer would fit.

The small size is a perfect fit for my (large) hand, and squeezes into smaller places than the larger model palm nailer.

The magnet holds the nails well so you can drive them with one hand, just press and the nail is quickly hammered (vibrated?) into place.

You can stop early and leave the nail head up if you're just tacking things, or come back later and finish the nail flush.

Buy Stanley Bostitch PN50 Mini Impact Nailer Now

This is another product that I give 5 stars, not because it is the best on the market (not industrial quality) but is a good deal for the low price. I had a project where I needed to drive 240 nails in tight, overhead areas could have done it with a hammer but my wrist and shoulder hurt just thinking about the prospect.

Had this puppy in a couple days with Amazon Prime, quickly reviewed the instructions and 45 minutes later had the job done didn't even break a sweat.

Will probably submit a video of this in action because you have to see it to believe how easy it makes a job like this.

One word of caution, read the instructions about how to insert the nails. It's pretty easy to accidentally "fire" this thing if you are not focused every time you load a nail and I imagine even a preacher would have some choice words if it fired with his/her finger over the nail point.

Read Best Reviews of Stanley Bostitch PN50 Mini Impact Nailer Here

I was very impressed with both the size and the power. Was able to sink a 3.5" spiral shanked nail with ease. The only disappointment is that the nail opening is rather narrow. The majority of common framing nails will fit, but if you try something with a bit larger head, it won't. Forget Roofing nails! This is the only palm nailer I've used, so I don't know how the opening compares to other brands/models. The speed of this nailer does not come close to a good nail gun, and the fatigue factor will be a lot higher. So it's great tool for tight places, and small to moderate volumes of nails, but if you are doing a large project, you might want to consider a stick nailer (preferable in addition to this nailer).

Want Stanley Bostitch PN50 Mini Impact Nailer Discount?

This thing is too fine! When a hammer or nail gun won't get to the nail, this will. I just used it to install an electric box in an 8" stud space in a corner with a wall that prevented any kind of hammer or even a screwdriver from working. It's simply amazing. All of this comes from a guy who has been doing this kind of work for 40 years and who owns a gas powered nail gun, air powered nail guns and all kinds of hammers.

You may not use this baby every day but when you do have a need, nothing else will get the job done.

Did I mention that it's very ergonomic in its shape?

Buy one and don't look back!

Save 15% Off

This is a perfect little nailer that does the job with any size nail. I've shot joist hanger nails up to 16d common any they go in very fast.I am extremely pleased with this nailer.

Frigidaire FAC126P1A Compact II 12,000-BTU Room Air Conditioner with Electronic Controls

This air conditioner I purchased new for around $269.00. Its small width, (hence the name Compact II) fits in the small width double hung window that I needed it for (I believe my window is 24" width). Most standard sized window units will not. This is one of the reasons for buying it, along with its low price. This unit blows extremely cold and cools my living room and kitchen with ease even on the most brutal summer days in New York. I have no complaints about the ability of this unit to cool whatsoever. My only complaint is it is extremely noisy it sounds like a factory. It is even very noisy at its lowest fan setting. The manual says to lower the fan if it is too noisy, but that is an exercise in futility. So if you're gonna have to hear it, might as well leave it at maximum. I like the variable fan speed feature. So one would be hard pressed to find a 12,000 BTU for the price of this Frigidaire unit, but you WILL be stuck with the noise. Frigidaire should reverse engineer a Panasonic air conditioner if they want to be serious about competing in this market.

I gave it a generous three stars because of its impractical noise levels.

Scratch the first review. I spoke, or typed too soon. Do not buy this air conditioner. After returning the first one because it was damaged before shipping, the second one has broken as well. Used it for about 6 days in total. The compressor has stopped working completely, just makes a buzzing sound and emits a burning odor. I've had it for about 50 days in total so the return policy is useless. I'm extremely dissapointed with purchase and feel like I have wasted $300+. Tried contacting frigidaire but no luck so far. Unfortunately I can't edit the original rating. I'll update this review with specifics on how Amazon deals with the situation. Again, be extremely careful if you are considering purchasing this air conditioner.

05/22/08 Just want to update this review in terms of how Amazon handled the situation. After calling and Emailing customer service I received an Email from Amazon stating that "As it seems that the problem with this item is more widespread than we originally thought, we are not able to send another replacement. We will gladly refund you in full for the return of this item." It took a few Emails but Amazon refunded me in full for the air conditioner and shipping. I was impressed with how they quickly apologized and offered a full refund; very good customer service. The air conditioner gets 1 star, but Amazon gets 5. I have since purchased an LG 8000 BTU air conditioner. The fan isn't quite as strong, but it's much quieter and the air gets just as cool as the frigidaire. I've used it for about 15 days and the compressor is still working.

Buy Frigidaire FAC126P1A Compact II 12,000-BTU Room Air Conditioner with Electronic Controls Now

Easy as pie to install, works exactly as expected. Keeps a huge room nice and cool. Was delivered in 2 days, love Amazon Prime.

Read Best Reviews of Frigidaire FAC126P1A Compact II 12,000-BTU Room Air Conditioner with Electronic Controls Here

I bought three of these for my office. 2 years later, all of the compressors have stopped working. Even when they were working, the three units were loud and they did not cool very effectively. Based on my experience with these air conditioners, I will never buy Frigidaire again and I would recommend you avoid them.

Want Frigidaire FAC126P1A Compact II 12,000-BTU Room Air Conditioner with Electronic Controls Discount?

I spent 3 hours reading specs and reviews on window units. This had the highest energy rating (10) when I bought it 4 summers ago. It cool 540 sq ft. I live on the second floor and the central air couldn't maintain in the dead of summer. This unit saved my summers. A big plus is when fall is cooling down and spring is heating up, there are many weeks you can use this unit (with a fan blowing into your main living area) by itself and save on central cooling. I keep it in the master bedroom so I can turn off the central air at bedtime and sleep in a comfortable room. Its has been the most money save purchase I've made in years. Very important! It' footprint allows installation into a small window. Don't forget to measure.