All Power America APC4008 1/3 Horsepower 3 Gallon 100 PSI Air Compressor With 7 Accessories & 25-Foo

• 3 Gallon Tank
• 100 PSI maximum pressure
• Oil-less pump
• 0.7 CFM @ 90 PSI, 1.5 CFM @ 40 PSI

This item arrived re-packaged and taped shut. It was used, broken and someone had tried to repair it before they returned it. Apparently there was no quality-control involvement in the re-selling of this item. It was supposedly new. The good news is that Amazon makes the return process relatively simple.

Buy All Power America APC4008 1/3 Horsepower 3 Gallon 100 PSI Air Compressor With 7 Accessories & 25-Foo Now

I purchased this compressor in 2009 to drain my drip irrigation systems for winter. I used it once to do that, blowing out the irrigation lines for approximately 12 small raised garden beds. Since then I have used it to inflate a few flat tires and it's otherwise been stored in a clean, dry tool shed. This fall when we fired it up to drain the irrigation system again, it did not work. After two days of trying to talk with tech support and to order a simple part, we are exactly nowhere. The company is extremely disorganized, can't transfer or return a call and can't even take an order for the defective part! The compressor is out of warranty even though we've only really used it once. Save your money and don't buy this piece of junk or anything else made by All Power America!

Read Best Reviews of All Power America APC4008 1/3 Horsepower 3 Gallon 100 PSI Air Compressor With 7 Accessories & 25-Foo Here

Im not happy with this compressor, I could get over the fact that it is really loud but I feel it does not work as well as it should. it takes along time to fill up the very small tank so even after just a couple of bike tires you have to wait to fill the system again. I would not recommend buying this, spend a little more and get a bigger one.

Want All Power America APC4008 1/3 Horsepower 3 Gallon 100 PSI Air Compressor With 7 Accessories & 25-Foo Discount?

well arent all compressors loud except the really expensive ones? this compressor not only is affordable on a low budget but also reliable, not to heavy, comes with many accessories and works well with my Iwata Revolution Bcr,If you plan on buying a compressor for the first time then get this one

Campbell-Hausfeld MP2875 Chisel Bits

• Compatible with medium stroke hammer (PL153499) and long stroke hammer (PL2534)
• One year warranty

I bought these replacement bits to remove floor tile in a bathroom in my air hammer. They each worked great at first, but about 60 minutes in, 3 of the 4 were already completely bald. I'm going to buy them again, as I'm almost finished the job, but if I were just starting the job I'd definitely consider a more expensive, reliable alternative.

Save 9% Off

Brass Straight Tire Chuck - Lock On - Quick Release

• Easier and faster air-filling - chuck locks on to valve stem for hands-free operation
• Great effort-saver for large inflation jobs; quick-release lever for easy removal
• Solid brass chuck precision machined for leak-free performance
• Straight design for easier connection; also available in right angle
• Air inlet female 1/4" NPT for all standard air hose fittings

Like one of the previous reviewers, I found these tire chucks to be defective in the design of the seal. I ordered 3 units for various air tanks and compressors, and each of them did not work at all. Basically, the seal between the brass housing and piston is made out rubber that is too soft, and at the normal 125 psi air pressure the rubber seal was pushed out of the chuck through the gab between the housing and the piston. I couldn't get any of them to work at all...no air in any tire. How frustrating when you are in the middle of a project on the farm. The only other possibility is that they machined the housing with too much room between the piston and the housing, and maybe no rubber seal (regardless of how stiff) would work with excessive space at that point. I'm looking for a refund unless the manufacterer fixed the problem and sends me new ones. These chucks might work at extremely low pressure, but I wouldn't bet on it. They are junk.

Buy Brass Straight Tire Chuck - Lock On - Quick Release Now

Unfortunately I found this product to be far less than expected. 9 times out of 10 when I try to use it, the cylindrical gasket becomes dislodged and will not seal, either on the valve stem or internally to stop the flow of air when you remove it from the valve stem. One time this seal shot across the garage under the air flow!

As a result, I am very disapointed in this product

Read Best Reviews of Brass Straight Tire Chuck - Lock On - Quick Release Here

don't buy this,it doesn't work! If you push it on as instructed, no air is allowed in to the tire.

Want Brass Straight Tire Chuck - Lock On - Quick Release Discount?

After 30 days of use, the tire chucks have held up pretty good. The handle fell off of one but was easily re attached. Much better to use than the ones that are angled. You don't have to remove the hub caps for wheels that have short valve stems.

Save 39% Off

The clip for attaching this item is good for cars and trucks, but for bicycles, it catches in the spokes if one is not careful. Overall it is a quality item which should last for many years.

Campbell Hausfeld CHN10299 5/8-Inch to 2-Inch 18 Gauge Brad Nailer

• Adjustable depth mechanism helps you control the depth of drive in various types of wood
• Quick clear nose provides easy access to jammed nails
• No-mar tip will not dent the wood surface
• Rubber comfort grip for easy handling
• 1.3 avg scfm @ 90 psi

Though this is the first air nailer I have owned, I have used a few in my life (also, I do have a 16 gauge Porter Cable "Bammer" finish nailer). After reading up on what features to look for in an air nailer, I chose this model.

It uses very little air, which is good because I only have a small compressor. It also has a directional exhaust to keep the air blasts out of your face and a padded tip to avoid marring the workpiece. The grips are very comfortable. I found that setting the nail depth was easy and accurate, as was loading the nails into the magazine. The heft and feel of this nailer is that of a good quality tool. Though I probably don't need to use 2" brads on most of my projects, it is good to have that option if and when I need it.

Basically, the only complaint I had was that the little bottle of oil that was included with this kit had a cracked cap, which allowed some oil to leak out in the case during shipment. Otherwise, this is a very solid brad nailer at a great price. I highly recommend it!

Buy Campbell Hausfeld CHN10299 5/8-Inch to 2-Inch 18 Gauge Brad Nailer Now

I needed a brad nailer for nailing some trim and toe kick in a kitchen. I wanted a Paslode for I have had previous experience with their products. Being a homeowner on a budget, I wanted a nailer for under $120. At the local hardware store, the salesman confirmed my thoughts about Paslode being an excellent choice. Paslodes cheapest brad nailer was over $150. Way too much money. I asked the friendly sales person what he would recomend. Supprisingly he recomended the Campbell Hausfeld 2" brad nailer. He stated they have sold tons of them, and they hardley ever come back. So I bought it. WOW. I was impressed, nice balance in hand, adjustable air port, depth control. The best feature is how little air it uses. My 4gal compressor hardly ran at all. It will drive 2" brads into oak with out a hitch. At $50 the only thing I can complain about is the tool oil it came with leaked in the case. So the nailer was coated in tool oil. Oh well. For home use I strongly recomend!!

Read Best Reviews of Campbell Hausfeld CHN10299 5/8-Inch to 2-Inch 18 Gauge Brad Nailer Here

I received this nailer as a gift, part of an air compressor combo pack ($79 Menards sale). I have previously used other, more expensive nailers and after 2 full days of heavy use, this nailer has impressed me. Although Campbell Hausfeld has been around for a very long time, I was afraid their quality has slipped as their products seem to be available at every discount and overstock retailer. To my surprise, this tool seems well made, and includes a nice set of features. I particularly like the ability to use 2-inch brads, a feature typically found only in nailers at twice the price. I may never need to buy a finish nailer. I also like the adjustable air port and contoured rubber grip. If you're looking for a decent brad nailer with enough money left over to buy the hoses and accessories you need (or another tool for that matter), give this a try.

Want Campbell Hausfeld CHN10299 5/8-Inch to 2-Inch 18 Gauge Brad Nailer Discount?

This has misfired or double fired a couple of times and other times works great. I am hesitant to use it where it would be very visible or where touchup would be difficult (like stained material).

Save 34% Off

I purchased this nailer for a specific small project. I choose this inexpensive unit thinking I'd seldom have a use for it. I've found it very handy to tack material in position before fastening with a framing nailer in two situations. It's very light and is easy to handle while holding a heavy piece of material with the other hand. Material doesn't move as the brad penetrates as often happens with framing nails following the grain or hitting a knot. Once tacked in position, the brads prevent the framing nails from moving the material. Every now and then I actually use it for it's intended purpose of fastening trim.

I'm very satisfied with the quality and performance of the tool. I've had one jam which was easily cleared with the quick release clamp (hit a knot I think). It's easy to adjust depth and quick and easy to add brads or change sizes.

A great tool!

Wagner Power Products 276124 Conversion Gun

• Paint spray gun for converting high-pressure compressors into HVLP fine-spray system
• 3 spray patterns; 89 percent product transfer efficiency; fluid and air controls;
• Works with compressors with at least 1-1/2 horsepower; all metal construction
• Includes conversion gun (0276124) regulator valve, bleeder and non-bleeder connections, needle/nozzle fine-finish projector set, 1-quart cup
• Weighs less than 6.6 pounds

Works extremely well, has all the features/adjustments of regular HVLP sprayers, works even with my little 2HP 6 Gal PorterCable pancake compressor that came with my air nailer. Granted the compressor does run more often than when your just nailing things, but I haven't had a problem as I build some furniture projects. I imagine painting a room or large objects would be better suited to turbine units that can supply a continuous airflow. But it beats spending hundreds more for a turbine unit that would just take up more space in my shop. If you have a compressor and want to try spraying finishes this is an economical way to start. A complete review can be found on the internet by searching.

Buy Wagner Power Products 276124 Conversion Gun Now

I purchased one of these guns from another site that sells them at a good price.

It's performed quite well and is very flexible. I have painted 3 rooms in my house as well as painted some furniture. Also, I have tested some water-based lacquer and it performed very well.

This is a great gun to buy especially if you already have a compressor. There are reviews on the internet (if you search you can find them) detailing successes using this gun with pancake compressors.

I am surprised and disappointed that Amazon is clearing this gun out given how well it performs. Not to worry if you buy one, there are other sites that sell this gun and numerous parts and extra projector sets. Just do a thorough search and you will find it.

Read Best Reviews of Wagner Power Products 276124 Conversion Gun Here

I just finished spraying a door with latex which is tough to spray even in the best of circumstances. Once I worked out the settings, the gun sprays nicely and evenly. The gun leaked at the packing seal out of the box and dropped blobs of paint on my door before I noticed the leak. The manual if you want to call it that is horrible. No advice on adjustments depending on material being spray, just a parts diagram and some crummy directions on how to hold the gun level. I'm used to spraying Acrylics and lacquers with my old Binks 62 so I know how to use a gun, I just need some advice on spraying with the HLVP process which is a bit different than the "old" days. The quality of the gun is good and it appears to be well made. It's a shame that Wagner did not put a bit more into the customer service side and include a decent manual.

Want Wagner Power Products 276124 Conversion Gun Discount?

Being my first HVLP gun I was quite pleased. For my first project I painted 6 chairs and 1 patio table with only 1 quart of black Rustoleum paint. That is how impressive the lack of over spray is on this gun. I used 15% Acetone in the paint and found the best way of measuring is to purchase some cheap semi-transparent measuring containers at your local hardware store.

Cleanup was a breeze as per the directions, just remember to spray the gun out in something like a trashcan.

Some pointers:

Even with the small amount of over spray, wear a mask. I didn't at first and after a good sneeze found black paint coming out of my nose. It may seem like common sense but it is something that is easily over looked.

The only problem I had with the gun is easily picked up in the instructions. There is a seal on the top of the paint canister that after some time of getting moisture will swell to get an airtight fit. When I was cleaning the gun with Acetone, the enlarged seal prevented me from properly locking the canister to the gun. Not noticing my mistake, I picked the gun up and the canister fell to the floor dumping the contents. Yes it was a mess to clean up, but a lesson well learned. The engineering could of been better on this aspect so beware.

Also when cleaning, take the needle valve out easier by pulling the trigger to send it out the back of the gun.

great gun! by removing the supplied regulator and attaching the quick connect fitting from your turbine gun you have the capspray titan II at half the price. save yourself the money and go this way.

Air Compressor Pressure Switch

• Kicks in at 90 PSI
• Kicks out at 120 PSI
• Metric Tubing
• Used for Most imported electric air compressors
• On off switch

This switch works great. The only thing was it is a universal switch so the fittings were not the same as my compressor, so I had to change all the fittings and alter the cover on my compressor but I didn't mind that and it works just like it is supposed to.

Buy Air Compressor Pressure Switch Now

If you are a handyman this is the right part for the job. If you are not comfortable doing high pressure pluming don't try this as a home replacement. It was a direct replacement for my Harbor Freight compressor pressure switch. It takes some thinking to get it in place and good technique (tape/ sealant) but if you have the right tools and are mechanically inclined go for it. I was glad to find an exact match at a great price.

Read Best Reviews of Air Compressor Pressure Switch Here

after I installed the new air pressure.I had to pull the top off to wier it up .I could not put the top on with the on-off switch button in place. Now I have to unplug it to stop it.

Tool Force A-C5 Air Brush Kit

• Air brush kit provides maximum versatility
• Working pressure of 15-to-50 psi
• Constructed with glass jars and brass fittings
• Includes fine head air brush, 15-foot vinyl hose, 2 3/4-ounce jars with lids, proper regulator, adaptor, and air brush body with finger valve
• Spray pattern that adjusts from 1/4-to-1-1/2-inches

It's my first air brush, I use it with regular heavy duty air compressor, and its work fine, the air brush have the adapter. Its easy to clean, and I'm not scary about to brake something in that little thing. So I think its good choice for beginners!

Buy Tool Force A-C5 Air Brush Kit Now

I have used this now for about six months. I had no airbrush experience when I purchased it and have used it for basic jobs, such as painting the hull on my model ship. It took me awhile to adjust it properly but then it did the job I was asking it to do. I only use water based paints so it is easy to clean and maintain. Don't expect to do hairline stripes or other fine detail work, this isn't the tool for that. I have had no problems with this, as long as it is clean, and it is the ideal airbrush to learn with.

Read Best Reviews of Tool Force A-C5 Air Brush Kit Here

I have had 3 of these airbrushes over the past 14 years and find they are fine for most all types of painting except for very fine lines or dots. Most of that can be overcome by masking.

Want Tool Force A-C5 Air Brush Kit Discount?

This unit came incomplete. It was missing the adapter to use with the 3/8" compressor line. Trying to figure out how to contact someone at Amazon about the problem was impossible. Finally gave up.

Save 5% Off

I bought this to use with Duracoat. This little gun works perfectly for Duracoat applications. I found the air compressor had to be set around 45psi for optimal efficiency.