Surebonder 9615, Upholstery Stapler with Carrying Case

• Safety mechanism prevents accidental firing
• Quick release magazine for easy loading
• Adjustable air exhaust
• Stapler viewer

This tool is a good value, coming in at about half the price of the others offered on Amazon. It does the job just fine, and while the fit and finish is not equivalent to higher priced tools it will give good service.

My main criticism is the manual: it is obviously written by someone whose first language is not English, important details are left out, loading instructions very ambiguous, and none of the specifications (operating pressure, staple size, etc.) are given in units that an American would understand. This is OK if sold to someone outside of the American market but potentially dangerous for those who are and can't do the conversion. Staple size is obvious because they are standard and Amazon sells the Surebonder staples (which are a good product and value as well I bought an assortment with the staple gun). Pressure: The maximum operating pressure in the safety warning works out to about 100psi. I get great results with 1/2" staples through loose weave fabric into pine at about 65psi adjust accordingly.

Loading staples: open the hopper (they call it a "clip", like a gun!) by pressing the lever at the back of the gun and the spring will push it out. Turn the gun upside down, pull the pressure plate all the way out, then put the staples in the bottom of the opening and snug to the front of the gun. Push the pressure plate mechanism back in until the lever engages with a click. It takes a bit of jiggling to get the pressure plate to slide over the staples.

Oiling the gun: they tell you to put one or two drops in the "joint" before operation then fire it a few times without staples in the gun. I think the joint is the opening where the staples come out, what I would call the nose. I assume that this is a once when you first use the gun operation, but maybe I'm wrong. Like other pneumatic guns (nailers and staplers) I put a few into the air coupling at the back every use. HERE IS THE IMPORTANT PART: you need to shoot many (20-30) staples the first time out before the gun stops depositing oil next to where the staple is shot. Glad I found out on a cheap scrap and not $250/yard fabric!!!

Safety nose: this should be no big surprise to anyone but since the manual doesn't mention it I will. The gun needs to be pressed against the surface where you are stapling so that the little metal plate that comes out of the nose is pushed back in. This probably only matters when trying to fire it without staples per the instructions for first time use nothing happens if you just pull the trigger with the nose not pressed against a hard surface. Note that the safety will easily mar a softwood surface, this should not be an issue with upholstery but I'm telling you now so you don't get an ugly surprise in the rare situation where that would matter.

Buy Surebonder 9615, Upholstery Stapler with Carrying Case Now

I love this stapler. I ordered it to do an upholstery job. My husband is in construction and has all the 'man-size' tools. His stapler wore me out and was too large to get in some of the tight spaces. This stapler is just the right size and strong enough to fire into the hardwoods. It's lightweight enough that I can use it without breaking my wrists. It's a great buy!

Read Best Reviews of Surebonder 9615, Upholstery Stapler with Carrying Case Here

Using Crex 1/4 staples jammed the loading slide. Only one staple would feed because Crex staples clamped the slide too tightly. This staple gun worked without flaw when loaded with Surebonder staples. Very easy to load and position for upholstering a captain's chair.

Want Surebonder 9615, Upholstery Stapler with Carrying Case Discount?

this is my first air powered tool. it works great. i used it with surebonder's staples and Campbell Hausfeld FP2028 1-Gallon Oil-Free Pancake Air Compressor. i am completing my fourth chair today and have used 5000 staples with no problems. it made this project sooo easy. it staples through layers and layers of heavy thick upholstery fabric and wood at only 60 psi and doesn't stop shooting until it drops to 40 psi. every staple seems to just go in so perfectly that i can barely see them afterward. i'm so glad i didn't spend on the more expensive gun that had all the good reviews. this one is a champ. i don't know how it works for anything other than wood and upholstery.

a couple quick notes if you hate instructions or are a newbee to tools like i am (also to correct an earlier reviewer's very bad info);

the staples go in upside down, pointing away from gun.

it works great with surebonder's 300 series staples. i haven't tried other brands.

if your compressor doesn't use oil then you must put a few drops of oil in gun at the air connection (this is the little bump at the tail of the gun). do this every 4th or 5th time that you load a row of staples and at end of each work day. don't forget to do it but don't over do it or your air hose will get blocked and need to be wiped out.

if your compressor hose will not connect to the gun, you'll need to go to hardware store and get a $2 quick connect. i thinks it's called a "male" quick connect. i just took the hose and gun to home depot and asked them which quick connect to buy.

there is an air exhaust knob on back of the gun that you will want to point toward our hand. it doesn't spray oil all over the place or anything like that but after a few hours of stapling, you will notice your thumb gets a little oily. it most certainly does not come out on the staples as someone said in a review, he totally put the oil in the wrong place.

the gun will not work unless you press it against something. it has a saftey on the nose of the gun for people like me that load the staples with gun pointing their face.

Save 31% Off

Purchased this tool to staple #30 felt paper to OSB boards on a roof during a re-shingle. My high-dollar stapler had blown its seal a few days before I was needing it so I ordered this gun on a quick ship to try and get by. I was amazed at how well it performed using very close to a full box of staples. Misfires were no more than the expensive gun so I plan to use this one till it quits (might even buy another). For the cost, you should be well pleased if purchased. Also has a carrying case for safe storage, oil for lubrication and is equipped with the male adapter to immediately get you ready for use.

Speedway 7296 5-Gallon Portable Air Tank

• lightweight and portable with handle for easy transportation
• Measures 11-3/8" x 9-1/2" x 16"
• 125 Maximum PSI
• Air-line shutoff and manual pressure relief valve
• 3 ft. industrial grade hose and standard tire chuck

I just got this little baby in the mail. $29 and free ship. how can you go wrong? super easy to fill. the gauge seems reliable and rugged. i will say, that it freaked me out the further i pushed the needle towards 125 so i stopped at 100 thinking, irrationally of course, that if it held at 100, i'd go to 125 next time. (seating tires freaks me out too...)

Buy Speedway 7296 5-Gallon Portable Air Tank Now

This tank is an excellent value for the price. Pervect size and capacity. Easy to transport from place to place. Highly recommend to potential buyers.

Stanley Bostitch CPACK3 Finish Nailer, Brad Nailer, Finish Stapler, and Compressor Combo Kit

• Combination pneumatic tool kit with finish nailer, finish stapler, brad nailer, and air compressor
• Power fasteners are lightweight and rugged; air compressor has a high-efficiency 2 hp (peak) motor
• Nailers and stapler feature durable aluminum housing; air compressor has 6-gallon tank and oil-free pump
• Includes all fittings and hoses, 3,000 staples and nails, tool lubricant, and tool bag
• Power fasteners are covered by a 7-year limited warranty; air compressor comes with a 1-year limited warranty; when shipped, this combo kit weighs 62.2 pounds

This unit has turned out to be an exceptional value. All the nailers work great and the compressor of course has other uses around the shop. After completing my first project using the unit my only regret is that I didn't spring for it years ago. It makes far more difference in speed and quality of assembly than I had imagined.

Buy Stanley Bostitch CPACK3 Finish Nailer, Brad Nailer, Finish Stapler, and Compressor Combo Kit Now

I purchased the Bostitch CPACK 3 (compressor and 3 air tools). The price was excellent and I was excited to try out the unit. Packaging was very good, and showed no damage. I pulled the compressor out, and the plastic motor housing case was cracked 9 inches on the side and loose. The motor's belt was exposed behind this, but I was going to overlook this, because I don't have small children who would stick their fingers in there. I powered up the compressor, and tried all 3 guns. I was pleased with the quality of all 3 guns. Once the compressor didn't turn off, I turned it off with the power switch. That's when I heard & felt the leak between the regulator valve and the tank. After taking a quick look, I realized this was an obvious manufacturing defect that should of been noticed during a (hopefully) quality control test at the plant. This is when I decided I needed to return the product. I packed it back up, and after checking out the cardboard box, I decided that the compressor was cracked before it was even boxed. It was well packaged, and the crack seemed to be because the unit itself was dropped on its side before it was ever packaged. 3 stars because the compressor seemed of decent quality, and the guns did shoot evenly, and accurately. A non-defective unit would of earned 4.5 stars.

Read Best Reviews of Stanley Bostitch CPACK3 Finish Nailer, Brad Nailer, Finish Stapler, and Compressor Combo Kit Here

Used it to install window moldings and tack down some carpeting. Worked flawlessly. Love the package, and price can't be beat. Only complained is that the compressor is on the noisy side, but other than that, I would recommend this product highly.

Want Stanley Bostitch CPACK3 Finish Nailer, Brad Nailer, Finish Stapler, and Compressor Combo Kit Discount?

i bought this combo as a back-up compressor but it's going to the front line...

the combo arrived promptly without damage and the compressor and guns functioned perfectly right out of the box.the finish gun punched through 3/4 oak,3/4 ply and into the joist for its first test.all the stuff that comes with this combo(and the warranty for the tools)adds up to a very good value.i've (ab)used bostitch tools for years every day on the job for years and expect life will be no better for this combo;)

I am a weekend do-it-yourselfer. One project that I was working on needed plenty of trim work. After talking with some knowledgable friends and reserching on amazon I decided to purchase the Bostitch CPACK3 combo kit. For a 3 gun kit I thought the price was right and I saw the same kit at Lowes for the same price but I would have had to pay sales tax. Although I have only used the finish nailer, I did test the other 2 guns and they work fine. The finish nailer works great. I have gone through about 1500 nails and have not had one jam. The gun fits comfortably in my hand and is light weight. At start up the compressor is a little noisy but after about 3 minutes it kicks off and only occasionally kicks back on. Being a first time user of a finish nailer I am very happy with the purchase and have saved myself a lot of time.

- Quincy Air Master Air Compressor with MAX Package - 5 HP, 230 Volt Single Phase, Model# 251CS80VCB

• Industrial-duty US-made Baldor motor
• Industrial-duty general-purpose mounted and wired magnetic starter
• Less than 5 PPM oil carry-over (blow-by) rating
• 145-175 working PSI
• Pump RPM: 942

The compressor has been in service for two years now. It is quiet, smooth and recovers quickly. We ran it continuously for several hours on two separate occasions while air-stripping paint and running a small jack hammer but with good results. Although continuous use is not recommended by the manufacturer for this model the compressor performed without a whimper but did produce a significant amount of heat during these two periods and developed a little oil seepage from the crankcase gasket, but no leak. For a continuous use 5hp compressor you should consider the QR series from Quincy but keep in mind the QR model 325 would be grossly overkill for most users and very expensive by comparison, over $4000.00. Having a 50,000 hour service life this unit being reviewed will surely outlast me but it is nice to have equipment that I am sure will not let me down. It is constructed very heavy throughout but top heavy due to the massive pump (for a 5hp unit) so it should be bolted down to the floor or to a wide base/stand. I am very happy with this purchase and highly recommend it.

12V Mini Air Compressor Tire Inflator 250PSI with Pressure Gauge (Powered by Car Cigarette Lighter)

• 250 or 300 PSI
• For use with smaller car tires, motorcycle tires and other small tires.

The unit is like high impact plastic and the first time I used it was to pump up air shocks on my camper. The unit ran and ran for about 15 minutes but eventually got up to the 200 psi limit of my air shocks. The unit had that warm smell when it finished but was only warm to the touch. I hope it lasts because it works fine for my application. Pump would work ok for those 180 psi bicycle tires too but would take forever to pump up a car tire.

Buy 12V Mini Air Compressor Tire Inflator 250PSI with Pressure Gauge (Powered by Car Cigarette Lighter) Now

You get what you pay for. Its SLOW to air up car tires, and I ended up giving up and heading down to the local gas station. It did work well on my bike tire though. There is a written label on there that says don't use for more than 15 minutes as it will overheat. Just a heads up.

Read Best Reviews of 12V Mini Air Compressor Tire Inflator 250PSI with Pressure Gauge (Powered by Car Cigarette Lighter) Here

Haven't had a chance to use it yet, but it looks as I expected. I'm sure it will work fine.

Interstate Pneumatics SA9M 4 Inch Diameter -1/2 Inch MPT Metal Body Compressor Air Intake Filter wit

• Greater durability than other filters in the market
• Designed for use with most of the brand compressors
• Filtration Efficiency Over 99%

It was a good price but it needed work to function. The filter is not tall enough to seal in the housing. When the cover is installed and tightened it hangs up on the inlet tube on one side. to let the cover sit flat and seal on the filter I had to cut a notch in the cover.

Amico 19mm Male Thread Air Compressor Plastic Muffler Filter New

• Product Name: Air Compressor Muffler
• Used in: Air Compressor; Material: Plastic; Color: Black
• Dimensions(Approx.): 86 x 65mm/3.4'' x 2.6''(D*H); Thread Size: 19mm/0.75''
• Outlet Size: 22 x 10mm/0.87" x 0.39"(L*W); Weight: 75g
• Package Content: 1 x Air Compressor Muffler

This muffler is an exact replacement for the one that came on my compressor. My compressor fell over in the bed of my truck and broke the muffler. I couldn't find one that would fit anywhere. It was impossible to find one with 19 mm male thread in my small town. When I found this one online I was skeptical due to the low price, but it turned out to be exactly what I needed. and it arrived very quickly.

Metro Vacuum 12-IDA32 Magic Air 12-Volt Inflator/Deflator

• All steel construction
• weather resistant, powder coat finish
• Compact, portable and easy to use
• Includes power unit with large and small-valve adapter nozzle
• 1 Year limited warranty; Made In USA

My friends and I have been using this product for many years to inflate our whitewater rafts. It works well, and I like that I can use it to deflate the rafts as well as inflate. This is a big plus at river take-outs when we need to deflate the boats as quickly and completely as possible to get them loaded on the trailer. This product WILL NOT completely inflate a raft, because it isn't designed to. This is a high volume, low pressure inflator. It will quickly get your raft to about 60-70%, then you must use a high pressure pump to top it off. I'm not sure that folks understand that when they buy it. They think it's not working right when it doesn't get their inflatable item rock hard. I also like that this product comes in either a 12-volt model and a battery clamp model. I prefer the 12-volt model for ease of use in the front and rear cargo area outlets of my SUV. The only reason I have to buy a new "orange torpedo" every few years is that people aren't careful, and they keep stepping on/ driving over the plug end.

Buy Metro Vacuum 12-IDA32 Magic Air 12-Volt Inflator/Deflator Now

I purchased this product hoping to use it to inflate water tubes and towables for tubing with our bowrider boat. This inflator does not have the power to inflate a even a one person towable tube. I had to go back to my hand pump to do the job. It also doesn't come with any adaptors so you need to mail order the adaptors for $4.50 plus $5 S&H just to be able to use the product.

Read Best Reviews of Metro Vacuum 12-IDA32 Magic Air 12-Volt Inflator/Deflator Here

I bought this to air up a lake float. It seems to be solidly built but has a weak fan motor. It is not good for anything that needs pressure.

Want Metro Vacuum 12-IDA32 Magic Air 12-Volt Inflator/Deflator Discount?

I purchased this item and it only ran for enough time to fill up two rubber rafts, a total time of about 2 hours then the motor started making a funny noise and then the unit totally quit working. I would not suggest buying this item, it really gets HOT after only a few minutes of running time and is really LOUD. Save your money and purchase another inflator/deflator.

G.W.

Save 22% Off

I used Magic Airs 12 years ago when I was a raft guide. I switched to LVL a number of years ago because they had a little more volumne. But the LVL's seem more delicate-not a good thing on the landing.

When I got this one, it didn't put out the volumne that I remembered, so I cut off the cigarette lighter plug, put on clips, and attach right to the battery. That increases the output. I don't know what that's all about. I had never seen one with the cigarette lighter plug before. I see now they make them both ways.

I would buy one again if I was shopping for an inflator.

Air Vent Inc. 24' Whole House Fan 54301 Attic & Whole House Fans

• Air Vent #54301 24" Whole House Fan
• AIR VENT INC.

I've put in three whole house fans over the years. I installed this one a few days ago and am very pleased. I deviated from the instructions in two ways to reduce noise. First, I never follow the advice to put the fan in the middle of the house. I put it as far away from the master bedroom (no children) and around as many corners as possible. In this case, after finding I had an unusually tight-fitting garage door I put it in the ceiling of the garage. My door fits so tightly I can see no light around any edge, so the fan will produce a vacuum in the garage and pull through the door to the house if blocked open. That put it even farther from the MBR and around more corners than anywhere else in the house. Second, I stapled dark gray foam pipe insulation, the kind available in 6' lengths at HD or Lowe's, around the bottom and outside edge of the wooden fan frame. I cut one of the lengths of 1" insulation in half lengthwise and wrapped it over the bottom and up onto the side, maybe an inch, all around the base of the fan's frame. That prevented direct contact between the fan's box frame and any ceiling joist. I installed lumber between the joists under the frame and the fan sits on that (plus the teeny normal contact point on the center joist). I did not bolt the fan down (noise), but just put 1x4 lumber around the edge to keep it from going sideways. The 1x4 touched the foam also, on the sides. Since the fans pulls itself down as it pushes air up, floating the fan within the confines of the 1x4s around the edges holds it place nicely. With a separate 12-hour timer I can go to be with it running and it shuts off after things cool off. The fan is quiet enough that you can talk in a normal voice in the garage while it is running on high speed. By the way, it makes no difference where you install this thing as far as effectiveness goes. A vacuum in the house is a vacuum in the house. It will pull nicely from wherever you open a window or door. Installation took 5 1/2 hours plus about 1 1/2 for the timer because I had to fish an insulated wall and because I bought the wrong kind of electric box for the timer. If you use a timer, buy an electric box for "old work." It is made to install in the sheetrock, not to be nailed to a stud and will go much faster. Be sure to block open any door that can slam before you turn the fan on. Doors will slam shut HARD and maybe break something. I thought this fan might be too small, but it's not. When they tell you it's good for a 1500 sq ft house, it doesn't really mean anything. This house is considerably bigger than that. The size of fan has more to do with how many doors and windows you can open and still get enough air movement. With this one, you can get a very gentle breeze with one door plus one sliding glass door (we have no bugs). I really like my foam invention. This fan is noticeably quieter than my previous fans. You will need a helper to install the shutter. You can't hold it up and install a screw at the same time; at least I can't.

Buy Air Vent Inc. 24' Whole House Fan 54301 Attic & Whole House Fans Now

This is a really great Fan! After my $ rebate from my electric utility, I ended paying about $ for this item. I performed the installation in accordance with the instructions and this unit is very quiet, other than the whoose from the wind going up into my attic. To be truthful, I was fearing the noise but this unit makes less noise that my stove exhaust fan! I am a happy camper with this deal, when it switched on it produces a nice cool breeze inside my home. My advice is use the template that comes with the fan, take your time, and follow the simple installation guide.

Good luck with your next project!

Read Best Reviews of Air Vent Inc. 24' Whole House Fan 54301 Attic & Whole House Fans Here

I can hardly believe how effective this fan is. Our home is not an open floor-plan, so we used to struggle with getting airflow in different rooms. This whole house fan creates a nice breeze throughout the entire house (1800 sq ft). I installed this in the center hallway, and I can feel the air drafting through the furthest windows. Since you do not need to cut through ceiling joists, I was able to easily install this by myself. The most difficult part was ensuring that everything was centered before cutting through the sheetrock. I also wired this to a switch and left it on the high setting instead of using the pull chain. I work very slowly and methodically so it took me 6 hours to install, but an experienced handyman could do this in half the time. Throw away your window fans and invest in a whole house fan. You will be so happy that you did.

Want Air Vent Inc. 24' Whole House Fan 54301 Attic & Whole House Fans Discount?

After many years of wanting an attic fan in my "new" home I finally bought and had this fan installed. The fan works great and is very quiet except the noise of the fan blades circulating the air zero or very little motor noise.

Only two complaints.

1. The sheet metal opening at the top of the fan had 4 random dents in it. If you look at the picture, the dents were on the raised rim that circles the top of the fan blade. The installers were wondering if I should send it back because it may have been knocked around in transit. I told them to test the fan motor and continue with the install if it worked since the dents were pretty much cosmetic and only visible from up in the attic when installed.

2. My other complaint is the cheap louvers/shutters, while they work well (open and close) with the fan being on or off, are very flimsy and make random rattling noise when the fan is on. This prevents me from turning the fan on at night on the timer and falling asleep I am a very light sleeper. I can sleep with the steady hum of the fan running but the random rattling comes and goes which drives me nuts as I try to sleep. Fortunately, the way I mostly will use the fan is to turn in on an hour or two before bed to cool the upstairs and then turn it off and go to bed.

I plan to look around and if I can find quality louvers that exactly fit this fan I'll buy and switch out in a NY minute.

Pro: the company: I thought there was a problem with the fan I received (it turns out there was not), so I called Attic Aire. they were extremely friendly and helpful people. Attic Aire gets an A+ for customer service. Actually, it was a desire to give them recognition for their terrific customer service which made me want to write this review in the first place.

Pro: I too mounted the fan on a thick piece of heavy wall insulation (bought from a big box store); there is very little vibration and the noise is not an issue, we don't notice it at all. I bought the 24 inch fan, perhaps the larger fan creates more vibration and noise.

Pro: we have used the fan almost every day, even when it's not hot, since I installed it: it maintains a gentle breeze and keeps the air inside the house very fresh (which can be a problem when your daughter has two house cats).

An installation idea: as mentioned, I bought the 24 inch fan; the fan comes assembled to a wooden frame; this frame is about 27 or 28 inches across. But the rafter the fan has to sit on are 16 inches apart on center (the distance across three rafters, then, is about 34 to 35 inches). So I cut 1/2 inch plywood about 36 x 36 inch square, then cut a square hole (about 25 inches across) in the center of the plywood so the fan would sit on top of the plywood without falling through. I had to cut the plywood in half in order to get it into the attic, but that did not create any problems. I then attached the heavy duty (fire-proof) insulation styrafoam to the rafters, mounted the plywood on that, then mounted the fan onto the plywood.

Another installation idea: I did almost all the work from inside the room where the fan was installed, staying out of the attic until the end: cut the hole in the ceiling, then through this hole secured pieces of 2x4's between the rafters, then mounted the insulation, then the plywood, then the fan, then attached electrical wires to the fan, then pushed the wire cable into the attic. it was only then that I turned off the power to the house and climbed into the attic to wire the fan to the house electrical system (I really don't enjoy crouching around and balancing between rafters in the attic -and needing that one tool left by mistake in the downstairs).

Good luck with your project.

Klimaire 9,000 Btu 19 SEER, Energy Satar, Ductless Mini Split Inverter Air Conditioner & Heat Pump,

I recently built a new backyard workshop and needed an A/C unit for the Texas heat. I could have just put in a window unit; but, I wanted something that was more efficient, quieter, and that didn't block my single window.

After some research, I opted to go with this Klimaire unit since it had the features I was looking for and is also geared more toward installing it yourself than the competing models are.

Anyway, here are the things I like about the Klimaire Mini-Split:

1) It really was pretty easy to install. I'll talk about this more in a bit; but, there are several videos online and the unit comes with pretty much everything you need.

2) It has A/C, Heat, dehumidifier, and fan settings. That covers pretty much anything I could want.

3) It is EXTREMELY quiet! Both the inside and outside units are barely audible, which makes it a lot more enjoyable.

4) The remote can be mounted to a wall and works great.

5) It is very efficient at 19 SEER. This shouldn't cost much to run at all.

6) It looks great and is very simple to operate.

Even though I am loving the unit overall, there is one irritating problem that I've run into. When the unit is on A/C mode, the fan will switch between levels 1, 2, & 3 it never turns completely off. That makes me feel bad leaving it on when I'm not out there (the building is extremely well insulated using foam). The dehumidifier setting does the same thing.

Fortunately, the Auto mode lets the fan turn completely off; but, it tries to keep the temperature in the room at an 'exact' level. So, in the summer, if you have the unit set at 78 degrees, it will run the A/C until the building cools down and can actually switch to the heater if the temp goes just a little low. It's crazy to be wasting energy running the heater in the Texas heat! The auto mode would be MUCH better if it would focus on a range rather than an exact temp. For example, if the A/C would turn on when the temp gets above 78, but the heater turns on when the temp gets below 65.

Anyway, that's something I can live with but it's still irritating.

As far as the install goes, the hardest part was running the electrical out to the building in the first place. I'd never done anything with 220 volt before, so it was a learning experience and took me a couple of days. Although, to be fair, I had to run electrical out there anyway. This unit requires a 220 volt, 30-Amp power supply.

Once the power was connected from my new sub-panel to the A/C disconnect, I basically followed these steps:

1) Put a couple of 18"x18" concrete pavers where I wanted the exterior unit and bolted it down.

2) Mounted the bracket for the interior unit to the wall.

3) Drilled a 3" hole in the wall where I wanted the pipes to go through. NOTE: The instructions call for a 3" hole, but I actually wish I had gone a bit smaller. Be sure to look at the conduit they provide for going through the wall, since that is actually closer to 2". I ended up filling around the conduit with Great Stuff gap filler.

4) Wired the provided electrical cable to the inside unit.

5) Ran both copper pipes, the drain pipe, and the electrical wire out of the building through the hole that was drilled in step #3.

6) Hooked everything up to the exterior unit.

7) Wired the exterior unit to the A/C disconnect using wire that I had leftover from wiring the building. I ran the wire through some 1/2" LiquidTite flexible conduit that I also had leftover, and that I had purchased from Home Depot.

8) I opened the lower valve and briefly pressed the discharge button on the upper valve 4 times to get the air out of the system. This process is shown on some of the online videos.)

9) At this point, I just wrapped up the pipes, made everything look good, and turned it on. :)

Overall, if you're looking for a highly efficient, and quiet A/C & heater solution this is a great choice! I would definitely recommend it, even with the irriating "Auto-Mode" issue.

Hey, Guys. I bought two units, the KSIM009-H219 and the KSIM018-H217. Research led me directly to the Klimaire distributor in Miami (I'm in Jacksonville) where they responded to my call for info. I bought directly from the dist where they cut me a break on the shipping for the two. Ordered on Thursday, they shipped on Monday SAIA freight and arrived in Jacksonville the next day where I picked them up at the terminal. Packaging was spot on, no issues.

Installed myself, but I'm no stranger to mechanical stuff. I think an installation of this sort for a newbie would be a challenge since there's so many disciplines involved. The biggest challenge is working with the supplied lineset and making sure you don't damage it or run short since you don't want to modify the length. Careful planning always pays off here. After the typical hookup, I vacuumed the lines for about two hours on both units, opened the liquid line a bit to charge the vacuumed lines and evap up to atmospheric pressure, opened both packing valves and buttoned everything up.

At this point checked for leaks with a leak detector solution and found I had leaks on three out of four connections. Some serious tightening solved those problems and I'd say that was the most surprising, it takes more than you'd think it would. I worked with a plumber for several years as a young pup and the answer to "how tight should this be?" was "till it stops leaking."

After flipping the breaker on the disconnects I started each system and have simply been amazed at how quiet and seemingly efficient these units are. I think you could run them both on power from a hamster in a wheel. Matter of fact, I did connect both of these units to my gen-set so we'll have cooling in those two rooms when the storm hits. Less than 4 amps on the small unit and 7 on the large unit. Amazing.

My thoughts on reviews. Anyone that is considering making a large purchase such as these will do some research and inevitably run across negative reviews and there are those here as well. But, any company that is putting forth the effort to bring items like this to market is not doing it to fail. Sure there are issues and problems that can and do arise, but that's from any company, with any product. More often than not problems stem from a language barrier, and this is where patience, compassion and persistence will help solve most problems. If you're looking for trouble, you'll probably find it. Those with a bad experience will rush to warn while those with a good experience will simply enjoy and move on so one needs to see all reviews in that context.

Of course most AC guys in the states hate messing with something they did not sell you, or something they are not familiar with. Most everyone is biased in one way or another. Knowing that and wanting to learn something new can make a project such as this rewarding if you do it yourself. Of course it's all at risk, and they'll be no shortage of people with a God complex to warn you of that fact.

All in all, I'd say that if you're a good car mechanic and know your way around the construction of a house and have an understanding of home wiring beyond the basics, you'll be happy.

Of course, mine could fail tomorrow.

Feel free to write me with any questions and I'll try to help.

All the best, Don

Buy Klimaire 9,000 Btu 19 SEER, Energy Satar, Ductless Mini Split Inverter Air Conditioner & Heat Pump, Now

I, like one of the other reviewers installed it in a workshop that I built in Texas. I have installed central air in the past, but it has been quite a few years. The biggest issue that I had was that the directions could have been worded better. I recommend that if you choose to install it yourself, watch a few installation videos on-line. This helps clarify a few issues that I came across with their directions. They do not have to be the same brand to understand the concept. There is an LG split system video (tips and how to) on You-Tube.

I found a discrepancy in the breaker size in the directions and the outside unit. I went with the 20 amp breaker stated on the actual unit, not the generic directions.

I did have to go out and purchase a vacuum pump, a set of gauges and an adapter for the gauges to hook up to the 410a refrigerant line. This required adapter is not included. Some people choose not to do this step and just purge it. I can't see how the moisture can be eliminated from the line set by skipping this step.

I put a kink in the low pressure line and decided to cut the section out and silver solder it.

Buy a bottle of leak detector from Home Depot or Lowe's to check the fittings. I really had to tighten down on the factory flair fittings to eliminate two almost undetectable leaks (so tight that I was afraid of breaking the line).

I did not change the length of the line set during the installation. This way I did not have to add or eliminate any of the refrigerant.

So far it is working great.

Read Best Reviews of Klimaire 9,000 Btu 19 SEER, Energy Satar, Ductless Mini Split Inverter Air Conditioner & Heat Pump, Here

I have not tried this product.

Before making a move for any product I want to see if they are real.

They do not list their address/phone/e-mail on their website. It is a mute point hiding that information from your customers these days. Here it is: 7909 NW 54th St, Doral, FL, (305) 593-8358 Sales extension 501. Support/Sales people never pick up: Nice classical music, put up a HiFi headset if you are interested in listening to that before calling. If you have only a cell phone do not waste expensive ether-bandwidth, put in a good classical DVD in your computer instead.

It is amazing how dump a company can be. They are sitting on gold mine with top of the line green product and they are screwing this up. I am mad at business people who screw up excellent engineering this way.

This product can only be sold with very strong support (it has bugs), and there is a market there that is tolerant to those problems as well as willing to pay higher price as you can see from the reviews.

If you live in Miami and feel like it, do visit their office and wake them up... Please.

Want Klimaire 9,000 Btu 19 SEER, Energy Satar, Ductless Mini Split Inverter Air Conditioner & Heat Pump, Discount?