DEWALT D55167 1.6 HP 200 PSI Oil Free High Pressure Low Noise Horizontal Portable Compressor

• 200 PSI max pressure allows for longer air tool run time
• 4.8 SCFM at 90 PSI allows for quick compressor recovery time
• 78 dBA (tested per ISO3744) operational noise level for a quieter work environment
• EHP efficient high-pressure technology delivers exceptional air-tool runtimes
• Oil-free, maintenance-free pump for convenient use

This compressor is a real knock out.

It goes up to 200 psi, That means more tool time before recharge compared to other copressors with same tank size.

Robust, Tank just feels thick, nice handles, guage protection.

I have used this with an air hammer for destroying concrete, automotive work etc.

It is a nice tire fill compressor because you can pump it up to 200 and wheel it around your cars and fill up without running the compressor.

It is loud, it is a compressor.

When draging it over objects be sure not to band the drain valve protruding from the bottom.

It's beutiful too.

Buy DEWALT D55167 1.6 HP 200 PSI Oil Free High Pressure Low Noise Horizontal Portable Compressor Now

I needed a horizontal compressor to fit under a countertop. And I wanted something that wouldn't make me deaf. I looked at all the normal major brands and wasn't impressed with their reviews and performance. This one Didn't have the quantity of reviews I would have liked to see, but the ones I did read were just about like I'm writing now.

It's compact, but it holds more PSI, so it keeps up with the work. It's relatively quiet also. I don't use it daily though, and I've only had a it a couple months. But so far I'm happy with it.

Read Best Reviews of DEWALT D55167 1.6 HP 200 PSI Oil Free High Pressure Low Noise Horizontal Portable Compressor Here

THE DEWALT D55167 IS SUPER! VERY QUIET. I USE IT ALL AROUND THE HOUSE, SHOP, CARS AND YARDS. THE 200# COMPRESSOR IS SO MUCH BETTER THAN MY OLD 120# COMPRESSOR. THIS IS MY THIRD COMPRESSOR AND THE BEST. THE INPUT AIR FILTER IS A GREAT IDEA. CONTROLS ARE VERY SIMPLE AND EASY TO USE........

Want DEWALT D55167 1.6 HP 200 PSI Oil Free High Pressure Low Noise Horizontal Portable Compressor Discount?

I bought this to replace my little 2 gallon compressor that I bought from Lowes. I was doing some wall texturing with the old one and it was painfully slow and loud (120psi, 0.3cfpm) and had difficulty keeping the pressure at even 40psi. The work looked too heavy (attempting orange peel). With the Dewalt, I can make it through a complete load of the hopper without the compressor turning on at a steady 60psi. The texture comes out even and just right. Even when the compressor does come on (at about 160psi), it fills quickly and much quieter than my old compressor. It's still louder than a belt compressor would have been but it cost half as much. Overall I'm very pleased with this unit. I'm not a professional, just a DIYer. This compressor definitely fits the bill.

Save 47% Off

Great product. Compressor is whisper quiet. Bought this for my garage at home. I had a oil free 5 year old compressor that this one replaced. The 200 psi is great for blowing off the dust from my 5th scale rc truck. Highly recommended.

Campbell Hausfeld RP071000AV 12-Volt Safety Inflator

• Compact design for storage in car
• Easily plugs into 12-Volt outlet
• Built-in flashlight for safety
• Keep your car tires inflate properly
• Includes accessories

I used this pump to fill my low SUV tire. I left it on for about ten minutes because it is slow and VERY noisy. It did the job but then my car wouldn't start. My battery was out for a while. The box that this product comes in is too snug so you can't store it properly and neatly. I guess for the price it's ok, just be careful not to let it run for too long. I learned the hard way. Also, the quality of the product isn't sturdy because half of plug tip just came apart after the third use.

Buy Campbell Hausfeld RP071000AV 12-Volt Safety Inflator Now

The reason I bought this is that I want to have an inflator on board for emergencies. The other day while on a trip I had to change a tire and put the donut on. The way this thing is mounted underneath my car does not allow to check/adjust the pressure w/o taking it down. As a consequence the pressure was way too low when I actually needed it. Luckily there was a gas station less than 2 miles away so I could bring up the pressure in the donut. Had it been a longer distance I might have needed a replacement for the donut in order to be able to get home. Anyway, now you know why I was looking for this device. I have no experience with any other inflator but this is what I think after having received it and used it once to adjust the pressure on both our cars. The light is not very bright and can only be used without the compressor running at the same time. This should be ok as you only need it to make the connection. It will not help you to read the pressure gauge in the dark anyway due to its position compared to the gauge. I was amazed how fast it brought up the pressure by 4psi on my Honda Pilot. The issue I have with this inflator is that the valve connector almost gets stuck to the valve stem and needs to be ripped off. I can imagine that this could create a problem in the long run to both your valve and the connector on the inflator. So, I will not use it on a regular basis but carry it with me in my car for an emergency which it appears to be perfect for especially when you consider the price.

DEWALT D51238K 5/8-Inch to 2-Inch 18-Gauge Brad Nailer

• Tool-free depth adjustment assists in locating the perfect depth setting for precise nail penetration
• Side low-nail indicator window allows user to quickly and easily see when it is time to re-load
• Overmolded no-mar pad increases visibility and reduces marring on material
• Tool-free jam clear eliminates down-time from bent fasteners caught in the nosepiece
• Tool-free 360 degree exhaust channels air and dust away from user;Trigger lock-off allows trigger to be disabled when not in use

Boy I like this nailer. I have owned it for almost 2 years and have no complaints. I've never had a misfire. It drives 2 inch nails with ease. Best of all it's light. I used it for window and door molding and cabinet work. This gun is easy to load, and easy to change the depth of the shot.

Some nice features are:

1. As the nails run low, an indicator appears to show that you have 6 nails left. Then it moves to show a countdown to show when you are empty. It's nice not to have to open the magazine to see how many nails you have. And of course the indicator that appears is yellow.

2. You can direct the exhaust airflow anywhere you want.

3. If the nail jams, which has only happend when I hit something below, the head easily opens so you can extract the bent nail.

I also have the 15 ga. nailer and would highly recommend both of these. I've also recommended this nailer to 2 friends and they have also had excellent results. Way to go DeWALT!!

Update: add another year of use, still working strong. No problems at all.

Buy DEWALT D51238K 5/8-Inch to 2-Inch 18-Gauge Brad Nailer Now

I bought a DeWalt nail gun near the end of last year. Since then I've driven several boxes of nails with it, mostly without any hitches. I've used it nearly every day for building cabinets and installing mouldings. This is my third brad nailer. My first one was a Senco SLP20, a fabulous gun. I never had any problems with the Senco other than the safty being on the front side of the driver... that made it difficult to shoot nails at a bit of an angle if needed. My only other complaint about the Senco was its limited capacity in length of nails, 1 5/8". After the Senco was stolen out of the back of my truck I bought a Hatachi brad nailer... the DeWalt was not yet on the market. Overall, the Hatachi was a nice quality gun and had the 2" nail depth capacity I really needed for my work. However, it would often double fire on me because the safty was so sensitive. This problem occurred so much I finally gave it to my son (a weekend warrior) after the DeWalt came on the market. I was real excited about the new DeWalt brad nailer because of the nice features, particularly the design which put the safty behind the driver. It worked flawlessly right out of the box and I almost never looked back. At the time I was looking at the DeWalt gun I was also considering the new Senco gun that shot 2" nails.

Now after about six months I'm beginning to think I made a mistake buying the DeWalt. A recent problem has occurred that's quite troubling: The gun stopped firing and recycling properly. I thought maybe at first it was due to a blown O-ring or something like that. The only way I could get the cylendar to return was to uncouple the air hose. Then, I could shoot one nail before having to uncouple the hose again. Needless to say this was a pain in the rear. Another son, who is also in construction, told me he encountered the same propblem with his DeWalt brad nailer... which was even newer than mine. He was finally able to get his to work by adding oil to the driver and guide after opening up the quick release mechanism. I tried this, but used a super thin lubricant instead of the oil that came with the gun. It didn't work. Later I went back and it fired fine for about 10 shots and then stopped again. I've let it set for a couple of days now and just tried it again. It seems to work fine now, but obviously I'm concerned because I don't feel I can rely on it when doing a job on site... and that could really cost me time and money. So, I'm once again thinking hard about buying yet another brad nailer, the newly designed Senco 2" gun. I've really liked the DeWalt, but am concerned about it's relyability. I'm also put off because it may be necessary to buy a third nail gun in less than two years... this is getting expensive.

Read Best Reviews of DEWALT D51238K 5/8-Inch to 2-Inch 18-Gauge Brad Nailer Here

I just bought this nailer at Home Depot several months ago for our trim crew. We specifically use 18G bradders for shoe and other small moldings. This unit is the best we've ever come in contact with. The guys tried the Porter Cab tools and they don't seem to have the power to set nails and they don't feel nearly as durable as the Dewalt. The depth setting mechanism on this tool is tops as well

Want DEWALT D51238K 5/8-Inch to 2-Inch 18-Gauge Brad Nailer Discount?

I recently purchased this 18 gauge Brad Nailer and a Porter Cable Pancake Compressor for Christmas. I waited to write a review until I had time to test it properly and I am still not certain that I am giving the Nailer a proper review. To start with I thought that all of the fittings for connecting to a compressor would come with the Nail Gun but these items were not included. I purchased the necessary fittings, which were very inexpensive, set it up and started testing it. Since I have never used a Nail Gun before, I changed the trigger to the sequential trigger provided in the kit to prevent accidentially shooting too many nails in one place. I am happy with the way the Gun feels, with the depth it shoots brads, how easy it is to change the depth, eveything EXCEPT that sometimes it dry fires for no reason. I have tried doing the things the instructions suggest to prevent this but I was still able to dry fire once about every 15 shots. Other than this the gun is really nice and I hope that I can talk to someone at Dewalt to resolve this problem. As of Jan. 2 I can not get through to anyone at Dewalt for assistance. I will write again as soon as I get assistance and the problem is resolved or if the problem remains I will down grade my review.

Save 58% Off

I received this nail gun as a free gift from DeWalt for purchasing a certain amount of products from them. I had previously used only Spot Nails and Omer nail guns, available only through a supplier, but as soon as I tried the DeWalt, I could tell it was superior even to my Spot Nails gun. I've used it for two years now in the cabinet and molding industry, and as my shop has grown, I will be getting a few more of these nail gun for my guys to use. I have recommended this gun to all of my friends in the industry. I do not blindly endorse DeWalt products, but this nail gun really is a good product.

TEKTON 4592 Air Filter/Regulator/Lubricator Unit

• Complete Air Management System Includes Filter, Regulator, and Lubricator
• Filter Traps and Removes Harmful Water Vapor and Debris Particles from Compressed Air Supply
• Easy-Clean Filter Canister with Brass Drain Valve
• Regulator Features High-Contrast Dial Face and Oversized Adjustment Knob
• Micro-Fog Lubricator Creates a Light Oil Mist to Properly and Consistently Lubricate Moving Air Tool Parts

This is advertised as 3/8" NPT for the inlet and outlet, but it is really 1/2" NPT. Not sure if I'm missing something, but it seems everything else out there is 3/8" NPT, not sure why this is any different.

The product comes with an "Instruction Manual" but it is just a drawing of the unit fully assembled showing that an air compressor is connected on one end and your nailer or other pneumatic device on the other end. These are hardly instructions.

Also, I can't even find a website for the company to contact or try to find more information about the unit.

Buy TEKTON 4592 Air Filter/Regulator/Lubricator Unit Now

this product was the worst junk i have ever delt with. before it was even put to use, it failed. the plastic nut that holds regulator to mounting frame stripped out,way to thin for its purpose. also the knurls that are supposed to adjust air pressurs stripped flat, no way to c hange pressure. a very poorly made unit, dont even think about it!

Read Best Reviews of TEKTON 4592 Air Filter/Regulator/Lubricator Unit Here

Mine seems to have a VERY small leak. When the garage is dead silent, I can hear a faint hiss and my compressor cycles more frequently when this is inline than when it isn't. It's not a big deal but that's why it's only four stars.

Works well. You can adjust pressure and oil flow easily and it feels fairly sturdy. I don't think this would cut it in a real shop but in a hobbyist's garage, it's a great thing.

Jet 708118 JMB-UMB Universal Mobile Base

• Sturdy and strong mobile base suitable for industrial grade use
• Adjusts from 18-by-18-to-28-by-28-inches
• 2 fixed and two swivel locking casters
• Easy assembly
• 600-pound capacity

I recently decided to put four of my tools on mobile bases. Because of the different sizes of the tools, I ended up buying two from Jet (Jet 708118 JMB-UMB Universal Mobile Base) and two from HTC (HTC2000 Universal Mobile Base). Since all four showed up at the same time, I was in a position to make a head-to-head comparison of them, and decided to write about it. As a result, you'll find this same review under both the Jet and the HTC Universal Base listings.

Upon Arrival:

All four bases were purchased from Amazon with free shipping, and all four arrived within just a couple of days via UPS. The HTC base pieces were wrapped in bubble wrap inside a cardboard outer box, and the Jet bases were in Styrofoam cutouts inside a cardboard outer box, so nothing sustained any shipping damage.

The next day, before I even unpacked anything, UPS showed up again with a bag. Inside were two pieces of thick, perforated steel about 18" long no note, no explanation, no return address, nothing. It turns out that one of the Jet bases was missing these two pieces. Someone I assume at Amazon caught it and rectified it, literally before I knew they were missing. When I examined everything closer, it was obvious that this particular base had been purchased by someone else and returned to Amazon, then resold. Not a big deal, but I think that explains the missing/found parts.

Unpacking:

I opened up and unpacked one HTC and one Jet base at the same time, to compare parts, instructions, and tool requirements before starting.

The HTC instructions were a 20-page stapled booklet in three languages. This is a particular pet peeve of mine, since I feel that if a company is going to sell to a particular country, then the instructions should be in that country's language. Again, not a big deal, just a minor irritant.

The HTC parts list showed a total of 108 parts, including nuts and bolts. I carefully compared the list to the actual contents, and found that several of the listed nuts and bolts were not there, with others apparently substituted. More on that later. The instructions listed the tools needed as a 7/16", 1/2" and 9/16" wrench, 7/16" socket, tape measure, and pliers. More on that later as well.

The Jet instructions are a single sheet, in English only. One side has the assembly instructions, the other side has a complete parts breakdown. Most of the Jet base is preassembled, so the parts list only has 8 items on it. No tools are listed because none are required for assembly.

Assembly of the HTC Base:

The HTC base requires a lot more assembly, so I decided to start with that one while my patience level was higher. The instructions are not great, but they're not the worst I've ever encountered. This is one instance where it really pays to read and pay attention to them.

The instructions show a couple of different configurations for how to mount the casters. This is a nice feature, allowing you a little more flexibility in how the base will move after assembly.

I read through everything, measured the base as instructed (the drill press was the first tool to be mounted), and bolted everything together. The base size can be adjusted in 1" increments. Since the nuts and bolts included with the kit don't match up to what's in the instruction sheet, there's a little head scratching involved to figure out what goes where, but it wasn't too bad. Also, the substituted hardware doesn't match up with the sizes of the listed tools, including some nuts that are metric. An adjustable wrench solved that problem. All the hardware is of good quality no problems with snapped bolts.

The drill press is too heavy to lift straight up and onto the base, but the instructions suggest that you can put your tool up on blocks and build the stand around it. I tried that and it didn't work, I think primarily because a drill press has such a small base in relation to its height, and ended up being dangerously unstable. Instead, I laid it on its side, then tipped it up onto the base. Not ideal, but it worked. I will say, however, that with both the HTC and the Jet base, if you can get some help to lift the tools straight onto the base, you're far better off.

All in all including my aborted attempt at assembling the base around the tool and then having to take it apart again the assembly took about 2 hours. This is probably not the greatest kit for someone who's a novice at assembling things, or for someone who won't read instructions.

Assembly of the Jet Base:

The Jet base has two front and two rear corners with the casters already installed. Unfortunately, you don't have the same flexibility of caster placement that you do with the HTC. There are also four side rails that slip into the corner pieces, and are held in place by spring-loaded pins that snap into the holes in the side rails. Adjustment is done in 1" increments. Assembly took just a couple of minutes, with no nuts and bolts and no tools.

The first tool on a Jet base was the sander. Again I couldn't lift it straight up and on, but I "walked" in onto the base with no problems.

Operation:

The HTC has two fixed rear wheels that don't lock. The two front casters swivel, and lock via two bright orange, high-impact plastic levers that you step on. The levers are large and mounted on top of the wheels, so they are very easy to see and step on. With the wheels down, the base moves very easily and the tool feels stable, although it takes a little effort to pivot the wheels into their down position.

The Jet has two fixed rear wheels with locks, and two front swivel casters with locks. The rear wheel locks are pretty easy to reach and operate, but the front ones are on the sides of the casters and partially hidden, which I found made them difficult to see and even more difficult to step on. When the wheels are unlocked, the base moves very easily and the tool feels very stable in motion.

Stability:

You obviously spend a lot more time with the tool locked in the operating position then you do moving it around, so this to me is the most important criteria.

With the HTC, when the tool is in the down position it rests on two rear wheels and two adjustable front leveling feet. The Jet stand is always resting on the four wheels. As a result, the Jet base moves more, even when locked. The HTC leveling feet also allow you to adjust the base to conform to an uneven floor, something you can't do with the Jet.

But the biggest difference between the two is how the pieces fit and lock together. Because the Jet base relies on side rails that slide into the corners and lock with a single pin, there is a lot of movement between the pieces. The design makes it impossible to tighten any of the pieces to one another short of drilling the corner pieces and installing bolts and as a result there is too much flex and movement in the Jet base.

The HTC on the other hand, because of all those irritating bolts and nuts you have to install, is actually more rigid. I found a lot less flex in the HTC base, and when combined with the fixed leveling feet, I found the HTC base to be a lot more stable in the down and locked position then the Jet.

What Went Where:

Sander: The sander went onto a Jet base, and it fits the open stand very nicely. The tool rocks slightly in the down position, but it's a pretty heavy tool, so that seems to add some stability. The wheel locks are hard to reach and operate, but I rarely move this tool, so that's not a big deal. This one remains on the Jet stand.

Drill press: The drill press went onto one of the HTC bases, but in the end I found that I didn't like having my drill press on a mobile base. It's so top heavy that no matter what I did, it still didn't feel very stable. I ended up taking it off the mobile base altogether.

Router table: This went onto the HTC base as originally intended. It moves very nicely when necessary, and locks down nice and stable the rest of the time. I'm very happy with this setup.

Bandsaw: Initially, the bandsaw went onto a Jet base. But as I mentioned above, there was too much flex in the base for the saw to feel very stable. This is also a tool that gets moved more often, and the Jet caster locks were too much of a pain. I ended up taking this off the Jet base and putting it on the HTC that had originally been used for the drill press, and again I am very happy with it in both the rolling and locked positions. The second Jet base was returned to the store.

The Bottom Line:

Despite the Jet having a clear advantage in how easy it is to assemble, I would definitely recommend the HTC over the Jet. You have more flexibility in the location of the front casters, the caster locks are easier to operate, there is less flex in the frame, and the machines sit down with more stability in the locked position.

Buy Jet 708118 JMB-UMB Universal Mobile Base Now

This base is awsome. I moved my table saw to this from a delta base and couldn't be happier. The assembly took a total of about 5 minutes since there is no hardware to worry about. As to the people that saw this doesn't lock well enough for a table saw, turn the base 90 degrees. No mobile base should be set to roll in the outfeed direction of a TS. If you lock the back (fixed) casters, then the front casters can't turn so it becomes very solid.

Read Best Reviews of Jet 708118 JMB-UMB Universal Mobile Base Here

After reading reviews of the HTC 2000, and knowing about the Delta UMB from personal experience, I decided to give the Jet a shot. I am glad that I did. Before getting to the review, though, five stars to Amazon's shipping department which shipped this product within a couple of hours of the time I placed the order. It hasn't arrived yet, but I bought a second one from my local tool shop. (OK, I'm weak. I couldn't wait.)

This mobile base was very simple to set up. The spring-loaded pins locked firmly in place, and I was able to perfectly size the base to the cabinet of the 8" jointer that now rests on it. To ensure stability, I cut a sub-base from 3/4" ply, placed that on/in the base, and then placed the jointer on top of that. I then bolted the two side tabs on the jointer cabinet to the ply.

With the wheels running opposite the length of the bed, the jointer does not move at all when being used. When it does get moved, though, it is very smooth and confident. I can't give five stars those wheel locks are an unfortunate wart on an otherwise excellent accessory.

Want Jet 708118 JMB-UMB Universal Mobile Base Discount?

I bought this base for a Craftsman 10" hybrid cabinet table saw (weight approx. 430 lbs). This base was extremely easy to assemble -took only a couple of minutes and no tools needed for assembly. Very solid and moves smoothly. I can move my table saw around without any difficulty whatsover. The base was very easy to adjust to the dimensions to my table saw. Two of the wheels lock with a foot lever. On smooth flooring it will still move slightly with effort, but wheeling it onto a rubber mat eliminates that. Overall, I am very happy with this purchase and would happily buy another one (which I will probably do when I buy a jointer/planer).

Save 16% Off

I recently purchased 2 mobile bases 1 HTC for my Jet 17" Drill Press and 1 Jet Universal Mobile base for my 10" Jet Table Saw. For the HTC It took 40 minutes, 4 or 5 different size wrenches/sockets,attaching the castors, hammering the ill fitted roller flanges (which I think will still slip), sorting out if the spring bumps go up or down and installing the PLASTIC levers.

With the Jet, In 5 minutes with no tools and no castor subassembly, with metal levers my table saw was up and rolling.

50' Auto-Rewind Air Hose Reel with 3/8" Hose

• Increase work-area safety, lengthen life of hose with auto-rewind hose reel
• Industrial-grade steel construction, heavy-duty coil spring, four-direction no-snag rollers
• Complete with 50-feet of 3/8" real RUBBER hose, solid-brass no-leak fittings and swivel connections
• Ceiling, wall or floor mount with sturdy, high-gauge steel bracket and 3" whip connector hose
• FAST recoil action with variable ratchet lock-stops

I was researching hose reels and found a wide range of quality and price. I hate buying the cheap stuff at the local bargain store (you can pick one up for about $30). But I know these cheap ones always have problems, and I know the high quality ones work without any problems. I know the high quality ones are dependable and they can take a beating (I've worked in a number of places that have these). However, a high quality hose reel it can be $400+. So I thought I'd try this one out being that the price is reasonable.

So it's been installed for about 2 weeks now and I have to say that I love it. I've read some reviews where this model won't extend all the way out and/or won't retract all the way I didn't experience this at all. My hose reel extends the entire 50 feet, and it retracts all the way. You can even adjust the retraction force when the hose is almost fully wound I found that the force was too high the way it shipped, and the end would "SLAM" against the stop. So I adjusted it so that I can let it go at any length and it will retract all the way with a small "BUMP" at the end.

Mounting to the ceiling isn't very hard, but you do have to dis-assemble the reel from the stand to do it (this is where I learned you can modify the retraction force).

Shipping was super fast and it was double boxed, so the reel was in perfect condition.

The only gripe I have, is the hose itself. The picture shows a yellow plastic like external covering. I know these hoses get dirty and having that "slick" outer surface makes cleaning easy but my hose is the standard black rubber. It gets dirty laying on the ground and that black rubber can mark surfaces (just like a shoe scuff). The rollers that guide the hose back into position are already black (and it's only been 2 weeks). But that's my only gripe I'm pleased with reel and I didn't have to spend lots of money to get good quality.

Buy 50' Auto-Rewind Air Hose Reel with 3/8" Hose Now

I was surprised at the quality of this reel for the price. I had priced similar hose reels with 1/4 in hose locally for a lot more and was not even close to the quality of this reel. The 3/8 hose mounted to the reel is quality hose and allows a full flow of air to my tools. The fittings used on the reel are heavy duty and should last for years. I would and have recommended this hose reel to my friends.

Read Best Reviews of 50' Auto-Rewind Air Hose Reel with 3/8" Hose Here

This hose reel is really nice. The hose and reel are both very heavy duty and will surely last me for years to come. I just hung it up in my gargage last weekend. The only issue I am having is that it does not seem to catch (so it does not wind up) as easy as I would like. I have to fuss with it a bit. I am trying to find an adjustment to make this work better, but it is pretty good as it is.

Want 50' Auto-Rewind Air Hose Reel with 3/8" Hose Discount?

I just purchased this hose reel after much research since it seems like the best value. It arrived well packaged (double boxed) and with no damage.

I decided to mount this on the ceiling of my garage. Since it is heavy enough to hurt someone if it fell I got a 2x2 foot piece of 3/4 plywood, cut it in half, and then glued & screwed the halves together. This gave me a strong mount that spanned two ceiling rafters. I inserted 4 carriage-bolts through from the top of the wood to serve as the mounting bolts for the hose reel.

Once everything was mounted the reel was very solid except that it there is some wobbling as you pull the hose out. This is because the actual reel mechanism is supported on just the one side (as you can see on the Amazon picture). To resolve that I cut a 14 inch piece of 1" by 1/8th steel bar and bent one end to meet the mounting wood and the other to meet one of the several unused holes on the side of the hose reel bracket. The unused holes in the bracket are 5/16 and will need to be drilled through to insert a bolt) I used 2 lag bolts on the end that attached to the plywood. Once that angled steel bar was in place it was much more stable.

Save 62% Off

I purchased this for my husband as he is trying to organize his garage. He curently has a monster air compressor and just had his hose draped over the compressor. This fixed his problem and he is very happy with the durability and quality of it. It was a perfect solution to our problem and he LOVES it!

Reelcraft 5650 OLP 3/8-Inch by 50-Feet Spring Driven Hose Reel for Air/Water

• Quiet speed latch mechanism
• Full flow shaft and swivel
• Multi-positional guide arm
• Baked-on powder coat paint
• Made from heavy gauge industrial steel

The reelcraft works just like it is suppose to BUT THERE WERE SOME SHIPPING ISSUES FROM UPS AND REELCRAFT.

1-THE FIRST UNIT/HOSE REEL WAS BENT UP!!! THE BOX HAD HOLES IN IT AND THE UNIT INSIDE WAS BENT UP SO I SENT IT BACK. NO ISSUES THERE WITH THE RETURN THAT WAS EASY.

2-THE SECOND UNIT/HOSE REEL WAS LOOKING OK FROM THE OUTSIDE FOR THE OUTER BOX INSPECTION SO I ACCEPTED IT,,,

AFTER UNPACKING THE UNIT I FOUND THE 2ND UNIT WAS ALSO DAMAGED THIS TIME BY REELCRAFT NOT UPS YOU COULD CLEARLY SEE THE RED PAINT INSIDE THE BOX WHERE REELCRAFTS PACKING DEPARTMENT HAS VERY ROUGH HANDELING PRACTICES WHEN PACKING THE UNIT.

THE DAMAGE THIS TIME WAS ON THE SIDE PLATE AND IT WAS BENT OVER JUST LIKE INSIDE THE BOX WHITNESS MARKS SHOWED. ANYWAY I HAD TO STRAIGHTEN THE BENT UP UNIT SO IT WOULD SPIN/REEL OUT AND RETRACT BACK IN WITHOUT BINDING UP.

IN CLOSING THE UNITS WORKS FINE NOW BUT REELCRAFT AND UPS HANDELING DEPARTMENTS NEED TO BE INFORMED.

THANKS IN ADVANCE.

R.

Buy Reelcraft 5650 OLP 3/8-Inch by 50-Feet Spring Driven Hose Reel for Air/Water Now

This $230 Reelcraft hose reel isn't as user friendly as another manufacturer's reel of the same size that I own, which I will add was purchased at only a third the price. Surprising, the Reelcraft reel wobbles on the wall, and unfortunately, sometimes sticks when retracting the hose. This is a replacement to a defective Reelcraft that I originally purchased that had a plastic part that broke before it came out of the box, so I decided to move up to the "premium" model. This Reelcraft model only adjusts to two positions, but if only Reelcraft had drilled two extra holes in the reel mount, could have made this where it would adjust to a multitude of positions. FYI... both positions were not ideal for vertical mounting on the wall at my location, so I am not too happy with it but not terribly upset either. Base is narrow and could have used a couple more steel reinforcing ribs in the mounting frame, which likely would stop the wobble/bounce of the reel. Anyway, I decided to keep this one because it was such a pain to get mounted in the location installed and removal is just as painful, so ....