Showing posts with label powerex air compressor. Show all posts
Showing posts with label powerex air compressor. Show all posts

Tuesday, October 21, 2014

New Pilot Discharge Unloader Valve Check Valve for gas air compressor 95-125 psi

New Pilot Discharge Unloader Valve Check Valve for gas air compressor 95-125 psi
  • 1/2" Female NPT Inlet x 1/2" Female NPT outlet - 30 scfm - w/ hand unloader
  • 95-125 psi - (check out our throttle control cables for gas compressor listings)
  • Free Shipping

I wanted to build an air compressor out of parts that had come mostly from other compressors that I had had over the years, I wanted a gas engine powered compressor, so I took the tank and the pump and located a proper sized gas engine and built a deck to bolt to the tank and then bolted the pump and the motor on to the deck, using this Unloader to regulate the pressure building in the tank, for a continuous run unit the unloader works like the pressure switch on an electric motor compressor. it controls the air going into the tank or lets it exit to the atmosphere,

one still wants to use a safety relief valve as well, I also added the throttle control as well that when the unloader says the compressor is full, it lets the engine go to a idle until air is called for again an then it speeds up the engine and fills up the tank, '

It works well and even on a small tanked electric compressor it will let the motor keep running and not on on and off, I had an unloader on a compressor I used in construction and had both a unloader and pressure switch and by switching to by pass the pressure switch the the unit would then run with the unloader for operations that would cause the motor to rapidly start and stop, it worked well for some operations, (would use it for nailing roof and floor decks)

Sunday, October 19, 2014

DeVilbiss Auto Refinish Products Air Adjusting Valve With Pressure Gauge DEVHAV-511

DeVilbiss Auto Refinish Products Air Adjusting Valve With Pressure Gauge DEVHAV-511
  • DeVILBISS HAV-511 High Output Air Adjusting Valve Regulator With Gauge
  • Includes markings for the optimal operating range for the Devilbiss GTI Millennium, and GFG Plus Gun
  • Precise air control at the gun for best, consistent results
  • Impact resistant guage and break resistant lens
  • Lightweight design that fits and professional spray gun

This product is a must have with the DeVilbiss Plus paint gun! Works very well. Had to replace the gun and gauge after over about 8 years of abuse. Not bad for an everyday shop tool.

Save 20% Off

Friday, October 10, 2014

SDT 72327 Hose and Gun Oiler Replacement Fits RIDGID ® 318 418 Oil Bucket

SDT 72327 Hose and Gun Oiler Replacement Fits RIDGID ® 318 418 Oil BucketThis is a good pump for way less than the RIGID pump it replaces. It is pretty much the same thing except without the RIGID logo, which means it costs thirty some instead of one hundred some.

Friday, July 18, 2014

Ampro A1460 18 Piece Air Tool Accessory Kit Milton Type

Ampro A1460 18 Piece Air Tool Accessory Kit Milton Type
  • Complete kit for professional or home use
  • Includes most popular air tool accessories
  • Corrosion resistant brass couplers & connectors

I just received this in the mail. I selected free shipping and waited for these to come so I could use my new air compressor.

When it arrivedI was was shocked to notice that there was one piece missing. This was especially odd since it is in clear packaging with each piece occupying a molded plastic space. No big deal since there were two more identical pieces, and I wouldn't need all three.

But... man do these things leak air. I used tephlon tape and wrenches to seal and tighten thembut they just wouldn't work. I wound up getting some quick attach pieces from my neighbor which work great.

Alsothe tire gauge and hand sprayer are CHEAP. I didn't care about the tire gauge, but the other piece I need/wanted. I feel like I could snap it into a few pieces with my bare hands. Not good.

Don't go cheap. Buy some quality parts.

Buy Ampro A1460 18 Piece Air Tool Accessory Kit Milton Type Now

Basically, here's what you get.

* A trigger nozzle for blowing air. It comes with a plastic reducer tip or a stepped brass tip if you want to fit it with an extension hose (handyI needed exactly that to blow the garbage out of a boxed car frame)

* A tire fill (handy)

* A 1/4" female quick coupler and assorted nipples and attachments (handy)

Others may have lucked out with tight fits but all of mine required plumbers tape when the nipples were installed. As far as them being solid brass,theoretically yeah, but they definitely went VERY heavy on the zinc and VERY light on the copper when they made the brass alloy. You pick up the fittings, they're light and tinny.

This is a good kit as a backup or for light duty homeowner use, but it will most definitely not last through heavy commercial/pro use. In my case, I bought a small pancake compressor for the shop that will serve in a backup/secondary role so these were OK to be tossed on a pouch, tied to the compressor and used for that.

Little stuff required tweaking. In addition to needing plumbers tape on the fittings, the trigger nozzle needed lube in the release piston since it was sticky and gritty, the plastic air tip still had injection flash around the hole and had to be opened up with an xacto in order to blow properly.

So, if you're just looking for a dirt cheap accessory kit, this is OK. It's cheap, it's serviceable, it contains some little random fittings that you might not think to buy individually but if you ever find yourself needing one, you'll be glad you had them on hand. If you need pro grade stuff or are someone who expects everything to last for a while, these ain't it. They're in that 'Harbor Freight' level of 'adequate quality with low expectations'.

Read Best Reviews of Ampro A1460 18 Piece Air Tool Accessory Kit Milton Type Here

Don't buy this stuff. The fittings are OK but the nozzle and chunk are junk. The allowed free air flow straight out of the box and were useless for anything other than kids toys or paperweights. The tire gauge is only passable but I didn't buy this set for this item. And, or course, Amazon was really helpful with the return.

Want Ampro A1460 18 Piece Air Tool Accessory Kit Milton Type Discount?

Pros solid brass fittings.

Cons none. I wish they included a bag with fittings. i just keep my fittings in my bostitch 3 nailgun bag.

note talking to my friend he said the red handle on the air gun eventually weakens and gun eventually fails to work properly. i guess we'll see.

Parm

Save 45% Off

A nice affordable kit. Plenty of Fittings.The Tire gauge feels cheap and the handle is okay, not top notch, But it does the job. I recommeded it for home use.

Thursday, September 26, 2013

Frigidaire FRA126CT1 12-000 Btu Window Air Conditioner W / Temp Remote

Frigidaire  FRA126CT1 12-000 Btu Window Air Conditioner W / Temp Remote
  • 12-000 BTU cooling capacity with variable speed fan
  • Cools room sizes up to 640 sq. ft.
  • 8-way air direction control
  • Clean air ionizer; Anti-bacterial mesh filter type- tilt-out filter access
  • Electronic controls with temperature sensing remote

The 12,000 BTU unit is a bad choice for most people. The smaller 10,000 BTU unit is 33% less in cost and typically much more reliable. The bigger 15,000 BTU unit is not that much more than the 12,000 unit.

So why would you pay so much extra above the price of the smaller 10K unit, yet stop short of going all out for the 15,000 BTU unit? Only one reason window height. Beyond 12,000 BTU the case gets much larger, which means it won't fit in some window styles.

Price not important? Measure your window, and if it fits get the bigger 15K unit.

Price important? Then why would you pay so much more for this one over the 10K unit?

I've bought and run this size, but only in special cases where I was restricted by window size and had a really large room to cool.

Also to consider... here's the review I gave on another model that is relevant to this one:

------------------

Between family and rent houses I put all types and sizes to the test every year in the scorching Texas sun. Here's my experience:

If you want a solid window air conditioner, it really boils down to two choices: Frigidaire and LG. The current "sweet spot" on reliability/price/economy is the 10,000 BTU unit regardless of make/manufacturer.

Recently they've been making 12,000 & 15,000 BTU 110V (normal plug) units.

-The 12000 BTU truly is 20% stronger, but you pay 50% more here on Amazon.

-The 15000 BTU is a snowball tossing beast, but it's in a larger case that may not fit your window (height-wise) and doesn't have a long history on the market so we don't know how it will do long-term

LG Pros The 10,000 BTU LG is my "workhorse". Best value. Run them till they fail in 4 to 7 years, then swap `em out for another.

1) Better warranty (but really, who cares when it breaks because you're sitting there sweating)

2) Typically last an additional 2-3 years over other brands

3) An LG rarely just stops running it will degrade slowly over a season

4) They are more tolerant of neglect (e.g. dirty filters... can't rely on tenant to care for your stuff)

5) Better withstands being placed in harsher environments (direct sunlight, restricted airflow)

6) Lower "lemon" rate

Frigidaire Pros For family I prefer to run 12,000 & 15,000 BTU Frigidaires. They are a little nicer, and I consider it worth it even though they always break sooner. (Value and reliability aren't as important, but I do have to compensate by keeping a new boxed spare around because they always fail at the most inopportune moments. Most people can't do this.)

1) A little nicer looking

2) Better features

3) Quieter

4) Slightly easier installation

5) Circuit surge/drain on startup seems significantly less (think lights flickering when compressor comes on)

Other parting thoughts:

1) A thing to know about newer units: To obtain the higher EER (efficiency) ratings, they use finer design on heat exchanger fins. For the non-experts, this means smaller little spaces that get jammed up with dirt/mold/whatever resulting in a clogged/filthy/poorly operating unit much-much faster than your parents' old units. Appliance repair stores can service your window unit every year (clean it of filth) that will extend life by at least 2 years and sometimes much more. Of course this costs anywhere from $50 up, and the units are cheap, so it's your call whether to service or toss it.

2) The 10,000 BTU Frigidaire here on Amazon is a good buy w/Amazon Prime shipping. For other higher BTU models, as of this writing you'll be paying more but also know that right now with the national heatwave most box stores are sold out so you may not have a choice.

3) Something this heavy is a risky ship (versus store pickup). It might be shipped wrong-side-up, or dropped, or whatever. It's a risk you'll run so do so knowingly. (I seem to have pretty good luck w/Amazon shipped items.) The risk is offset, however, by advantages of buying from Amazon (store would take forever, you'd have to load it and bring it home, have to have a vehicle large enough to carry it, etc.)

4) Clean. Your. Filter. Every. Week. It will keep your little ice machine healthy.

5) Different stores have different models from the same maker. If they are made in the same year, it doesn't seem to make a difference.

6) Tempted to go cheap like a Haier? Don't.

7) Tempted to buy a 6,000 or 8,000 BTU model? Don't. Get the stronger unit. It will cool down the room faster. It will not need to work as hard as a weaker unit and last longer. It is built with some stronger/better key components.

Good luck and happy cooling.

Buy Frigidaire FRA126CT1 12-000 Btu Window Air Conditioner W / Temp Remote Now

New unit was very noisy. Rather than return it, it was easier to it take to a local warranty repair center. I kept Amazon in the loop just in case, and they were gracious in offering to exchange the unit if I chose not to have it repaired.

The repair center diagnosed the noise as a bad bearing in the fan motor. The blower motor was replaced, and the unit is OK now. The motor being bad right out of the box suggests that these units go through no testing at the factory, and quality control is low.

After the repair, the overall noise level is about average which is OK with me. Most of the sound is the air movement swish of the blower. There is very little compressor sound when it is running, and a light "clunk" when the compressor turns off.

This 12,000 BTU unit is the same physical size as the 8,000 BTU Frigidaire unit I am replacing. For what it's worth, the blower in the 8,000 BTU unit lasted two seasons. That might explain why Frigidaire has only a one-year warranty (which is really one season) on that part of the unit. Perhaps Frigidaire is trying to take over Haier's role as the industry purveyor of cheap appliances.

I later found out that LG has a five-year warranty on everything -no need to buy an extended warranty. Frigidaire has five years only on the compressor, one year on everything else. The repair guy at the warranty repair center said he has seen only two LG units in the five years he has been there.

Having gone through multiple window units, I'll offer the advice that, in order to get the high EER ratings, these things (all brands) use delicate fins on the heat exchangers the design and spacing of which easily accumulate micro dust particles in spite of the filter. The moisture on the fins along with the dust encourages the growth of mold if the fins are not meticulously cleaned. But the delicate nature of the fins along with the presence of the electronic controls means you can't do like the old days where you took the thing out of the chassis and washed it out at the local car wash. Cleaning the fins now requires something like using a strong shop vac and a tooth brush to carefully comb fins clean at the end of each season.

In other words: It might have a high EER when you get it new, but it doesn't stay that way for long. It's too bad the EER is only for brand new in the lab, and no thought is given to the EER over a typical lifespan of the product.

Read Best Reviews of Frigidaire FRA126CT1 12-000 Btu Window Air Conditioner W / Temp Remote Here

I needed to replace a 10 year old 12,000 BTU Kenmore AC and thoroughly researched my options before zeroing in on this Frigidaire. The clincher was the unique remote control -it has a key feature that no other AC's have, including other Frigidaires.

Thermostat & Automatic Climate Control Built Into The Remote

Let's be clear -most modern AC's come with a remote that turns the temperature up or down, but that's NOT all this Frigidaire's remote does. It actually controls the climate via it's own thermostat and direct communication with the AC itself. The remote also has a digital readout that displays the actual room temperature at the remote itself. This is significant, because most AC's have a thermostat in the AC housing. But this Frigidaire has a thermostat built right into the remote control, which means the AC will cycle on and off based on the temperature at the remote, instead of at the AC unit. I hated how my old Kenmore would click off the compressor because the thermostat thought the room was cool enough, yet where I was sitting, was still hot and muggy. Now, with this new Frigidaire, the compressor keeps running based on the temperature on the remote's digital readout. Every few minutes the remote sends a signal to the AC unit, telling it what the temperature is; and the compressor adjusts, based on that readout, keeping the room a constant, consistent temperature. This feature alone sets this AC apart, head and shoulders above the rest. And after just a few days of using it, there's no way I'd ever want an AC without this feature from here on.

More About the Remote

Other than the awesome feature mentioned above, the remote can turn the AC on or off, set the temperature, timer on, timer off, sleep mode, auto fan and energy saver. It's also a cute little thing that feels good in my hand. It's about the size of a small cell phone and the rubberized buttons are well laid out and easy to use, even for those with poor eyesight and dexterity, like me.

Eco-Friendly

The power surge my old Kenmore caused would literally make the lights dim whenever the compressor kicked in. On really hot days, that sudden power drain would often trip the circuit in my fuse box, knocking the power out. But this new Frigidaire is so energy efficient, that I barely hear the compressor kick in, and the lights dim for just a fraction of a second. So the power drain compared to my old Kenmore is almost nonexistent. I feel confident that when we go through another round of brown-outs here in California, my Frigidaire will keep running even when Edison throttles down everyone's kilowatt usage. Even better, the Electric Company is giving me a rebate for upgrading to a new "green" AC; how COOL is THAT?!

Cooling Powerhouse

There aren't too many 12,000 BTU air conditioners out there; any higher in BTU, and you can't use a standard 3-prong wall outlet. So I was happy to find this 12,000 BTU replacement. This Frigidaire cools my 650 square foot room without a problem. Actually, I have yet to run it higher than Low speed, and at that setting, it's been cooling off the whole room quite quickly, and keeping it at a constant temperature. I know it's early in the season, but it's already gotten hot and muggy here in Southern California, so I've had plenty of opportunity to put this new AC through its paces already. But thus far, I'm quite confident this Frigidaire can more than handle the sweltering heats that are coming.

Clean Air

I have a couple different air purifiers, but it's cool that this AC also has a built-in ionizer. With all the air it blows around the room, it's good to know that I can turn the ionizer on with the push of a button, and minimize the dust flying around. For those of us with respiratory problems, this is a HUGE Bonus!

Installation

If I could find an AC that does all this one can, plus install itself, then it would be the perfect AC! Short of that fantasy, this AC was well worth the setup. I had help with it, and 2 hours later -voila -we were enjoying the reward of cooler air. The unit itself was a little lighter than the Kenmore I was replacing, but let's face it, it's difficult to balance a big, heavy, square object on a windowsill. We got the job done though, with no real headaches or problems. The side louvers were easy to attach, and the screws, brackets and weather stripping were all self-explanatory.

QUIET!

Some other reviews had me concerned about the noise level of this particular unit, but I have to say, this Frigidaire is about as quiet as an AC gets. I have a smaller 5,000 BTU AC in the bedroom, and it's much louder than this 12,000 BTU. My old Kenmore was waaaaaaay louder than this, even when it was brand spanking new.

Bottom Line -Frigidaire really hasn't done themselves any favors by describing and marketing this AC so poorly. They should be punching up what's special about this remote (the built-in thermostat,) how it interacts with the AC, and why that unique feature matters to consumers. It's truly one of a kind and that feature alone squashes the competition in my book. This AC is so much better than it appears, at first glance. Thankfully, I was very thorough in my research, both online and in store, and I doubt you'll find a better AC for the money than this Frigidaire. I fully expect this AC to work flawlessly for years to come; and because I'll have it for many years, I'm glad I took the time to make the right choice.

Want Frigidaire FRA126CT1 12-000 Btu Window Air Conditioner W / Temp Remote Discount?

I have a large room (about 600SF) with 10-1/2 foot ceilings in NYC. Two ceiling fans help move the air around. So the last two days have been 95F or thereabouts here in NYC, I've run the unit on low fan at 65F setting, and the room is chilly. At high speed the fan is kind of noisy, but at low speed you barely hear it, just some white noise in the background.

Turning it on full blast in a hot room, it takes a couple hours to really cool the room off, but maintaining a cool room, no problem.

Installation was easy enough to figure out, took all of 10 minutes.

So far am very happy with the purchase. Did the purchase via Amazon, a smooth, seamless process.

Save 17% Off

I use this window ac unit as a thru the wall cooler. It cooled three adjacent rooms during the hottest days of this past summer. I really appreciate the remote control, after several years using old fashioned manual controls. An unexpected benefit was the low noise. The unit is just a few feet from my TV and does not interfere with sound.

Monday, August 19, 2013

Ingersoll Rand 231P32 Protective Tool Boot

Ingersoll Rand 231P32 Protective Tool Boot
  • Keeps tools clean and protected
  • Bright red color makes it easy to locate your tool in a busy shop

I purchased my first IR-231 impact off of a SnapOn truck I spotted at an auto dealership in 1980, after my SnapOn impact had greatly lost performance in six months time. With it, I purchased a solid blue Ingersoll Rand protective cover very similar to this one I even received a serial numbered A.J. Foyt four time Indy winner commemorative knife in the deal (that I still have safely put away). Over the next thirty years my impact saw plenty of use, but never daily in any shop use. It still works great and looks good mostly due to that Ingersoll Rand protective cover I put on it all those years back and the great Ingersoll Rand quality. It has fallen to the concrete numerous times and been dragged around on concrete, but the old solid dark blue Ingersoll Rand protective cover has kept it looking good, and the drops apparently caused no damage due to the small cushioning allowed by the cover.

That old cover was really showing its age after thirty years, but it was still doing the job it had always done. When I pried and slid it off, my 1/2-inch IR-231 still looked fairly new after cleaning it up. I had just purchased a new 3/4" impact and I wanted a cover for it and, as I looked at Amazon for that one, I decided to see if there was one for my old IR-231. Almost surprised to find a new Ingersoll Rand protective cover for such an old impact, I found two one in transparent blue, and this one.

In the Amazon picture this red cover appeared solid but it is a transparent red. I had also noticed two holes on the transparent blue cover toward the upper front of the cover, as placed on the tool. My old cover didn't have those two openings, and I thought this red cover wouldn't have them either looking at the picture. This red cover does have those two openings also. I have no idea why they were added, but I now know there is no difference in the blue or red Ingersoll Rand covers offered here except price and color, and a different Ingersoll Rand logo imprinted on the cover.

As for installation, the fit was just as snug as my old original cover. It was about 80 degrees Fahrenheit when I was putting it on and it wasn't difficult to install and fits nice and tight. I didn't use anything but my hands and fingers to slide and pry it into position on my clean impact.

I have to say the new transparent cover has dressed up my old IR-231 nicely, and it matches the red backing plate where the serial number/model number information and the pin greaser port are, and it has the proper opening for that grease port. In the reversing and power switch area, it has slightly larger openings than the 1980 year model cover had but nothing I can see to cause any complaint. I still can't understand those two added dirt collecting openings, but they don't appear to be any real problem either. The material used also appears to be the same so, transparent blue or red, you won't go wrong with one of these protective covers.

Of note the IR-231 was about $180 in 1980 but the SnapOn dealer did give me a trade-in credit for my malfunctioning SnapOn impact. You can find a new Ingersoll Rand 231 here at Amazon for much less and you can count on it being a great reliable tool with little maintenance especially with one of the Ingersoll Rand protective covers.

Buy Ingersoll Rand 231P32 Protective Tool Boot Now

There isn't much to say. The charge of $9.00 is alot for this little peice of plastisized rubber. It is difficult to put on, but once on, it does its job. Is it important to have the boot? Probably not. But, if tools are important to you, why not protect them so they can give you their best service.

Read Best Reviews of Ingersoll Rand 231P32 Protective Tool Boot Here

Perhaps a review is not really needed for such a simple product but here's mine anyway. This rubber tool boot goes over your IR air ratchet. This is NOT a universal fit so please be sure you order the correct one for your particular model.

You may wish to heat it slightly with a hair dryer or apply a but of dish soap to make it easier to slip over the tool. I did NOT do that and had a but of a time getting the thing on. Once "installed" it does fit well and certainly protects my new ratchet as I'd hoped.

Want Ingersoll Rand 231P32 Protective Tool Boot Discount?

This is a great cover to protect the tool. Just drop it in boiling water for a couple of minutes then it will slide right on. Keeps the tool clean and provides some protection against drops.

Save 8% Off

i had one of these for years. when my unit failed after 30yrs. I replaced it with this new one.