Air Compressor Oil Breather Cap Clarke

• NEW

It doesn't... but it's made so nice that I intend to search for the correct adapter or eventually make one that works. Theses are wel made, brass, with a rubber seal at the base, a foam breather filter inside and a secure fitting brass cap. It's too bad every portable air compressor doesn't have a breather cap made like this!

Senco PC1131 Compressor, 2.5-Horsepower (PEAK) 4.3-Gallon

• Direct Drive Motor
• Cast Iron Sleeve / Cast Iron Head Cylinder
• Twin Tank Configuration
• Standard equipment includes 1/4" universal coupler regulator, pressure gauge.
• Delivers 4.3 cfm at 100psi

I have used this compressor for a few days now with a coil framing nailer and it works fine, has plenty of capacity for one gun, and is relatively quiet.

I would give it 5 stars except that packaging is poor and instructions for initial set-up are also poor. The compressor ships in its original retail box, not double boxed, and mine was torn open and then re-taped. The box says an oil bottle is included and there is space for it in the box, but in fact Senco is shipping with oil in the compressor and no oil bottle (I found this confusing as it looks like the oil bottle was stolen or missing). The air filter comes unattached and you have to figure out where to attach it on your own (a little sketch would be helpful for the spatially challenged). The air inlet has a plastic plug inserted so don't start your compressor before finding and removing the plug and attaching the air filter.

Finally, if you do happen to have a major problem such as a dead compressor, Amazon will not accept a return ("too dangerous") and will simply refer you to the distributor.

These may be nit-picky points, but I thought I would throw them out there to possibly help some one else considering this compressor.

Buy Senco PC1131 Compressor, 2.5-Horsepower (PEAK) 4.3-Gallon Now

The PC1131 has a 4.3 gallon double hotdog tank system. It has easy to read primary and secondary gauges and a switch that can be reached quickly but does not interfere with operation when moving the hose around. The compressor has a well positioned oil fill port, for spalsh lubrication. It's relatively quiet (though there is no such thing as a quiet compressor. I have used the Senco with brad, stapler and finishing nail guns as well as a framing nailer to drive both 2" and 3-1/2" framing nails. The recycle of the tank pressure (which I set @ 110psi) easily operates any of these tools without a need to wait for the pressure to build. The only issue would be using the compressor form spray guns, where a constant (uniterrupted airflow is a critical requirement of airguns). Other than that, I would strong recommend this Senco for everyday, portable use, especially for the DIY homeowner.

Read Best Reviews of Senco PC1131 Compressor, 2.5-Horsepower (PEAK) 4.3-Gallon Here

Everything about it seems to be good/ excellent value.

Pros: It's got lots of power to keep up, no compressor is quit, but this one is surprisingly not that noisy, the weight is quite reasonable to considering it's power. Oil-lubricated is quieter and lasts way longer than oil-less. Runs any air tool you will need, even roofing and framing nailers with no problem.

Cons: The rubber handle has ridges in it that hurt your hand if you carry it farther than a few steps without gloves. The copper air pipe is on the outside of the compressor, where it seems like there is more risk of damage (see picture on the left side of the plastic covering. The drains can sometimes hit your legs while carrying it, which is not pleasant. The pressure readings are a little difficult to see. There is only one air outlet instead of two.

Make sure you read the initial set up directions, to put on the air filter and the oil dipstick. I also suggest running it with all the valves open (screwed in clockwise) for 20-30 min. This is a good thing to break in any new compressor.

All in all, it's probably the best bang for your buck, a good purchase at two hundred something dollars

Want Senco PC1131 Compressor, 2.5-Horsepower (PEAK) 4.3-Gallon Discount?

Bottom line is that this compressor works well enough, but has a few design flaws.

I originally wanted a Makita MAC700, but when I was making my Amazon wishlist, it was out of stock. I should've waited, but eagerness got the better of me and I asked for the Senco.

As mentioned, it works as it should and meets my needs to power finish nailers (woodworking), fill tires, and blow crud off my garage floor. I wanted to upgrade from my current, dinky, 3 gal pancake compressor. The pancake was under-powered, leaked air, and was screamingly loud. The Senco provides plenty of power and 2hp/4.3 gals seems to be enough for my needs. Bigger would be better, but storage and portability were also concerns. The Senco is heavyish, but managable; and its footprint isn't much greater than the pancake compressor.

Is the Senco quiet? In a wordno. While its noticably less noisy tham my oiless pancake, it still makes a racket. The Makita is reportedly quieter, due to the larger bore and slower motor. Thats one of the reasons I originally wanted it, and kinda wish I held out for it.

So whats wrong with the Senco?

1The item received differs slightly from the compressor pictured. The gauges on the compressor I recieved don't face upward as pictured. They face inward, toward the compressor motor. This makes the gauges harder to read imo.

2The air filer housing was a hassle to install. There isn't enough room between the motor and air tank. You need to disassemble the housing, attach the small portion of the housing to the compressor motor, then muscle/squeeze the large portion back onto the other part. (See pic)

3The bottom gauge originally rubbed against the motor shroud. This would have caused excessive wear and vibration on the gauges and regulator. I was able to move the regulator/gauge assembley off the shroud by simply tightening the coupling that attaches it to the tank. Quick fix, no big deal.

All that said-

The senco works well enough that I don't feel inclined to return it for the Makita. Other than the minor issues I mentioned, it seems to be fairly well-built. My 5-year plan is to upgrade into a much larger compressor when/if I move into a bigger place. I'm sure the Senco will serve me well until I get there.

Save 31% Off

My Husband got this to use with his nail gun. He loves it. Helps him out in his huge array of projects that sometimes get finished.

Ingersoll Rand IRT315 Heavy Duty Air Twin Piston Straight Line Sander - 2-3/4-Inch x 17-1/2-Inch Pad

• 3,000 reciprocating strokes per minute
• Quick action paper clamps
• Smooth, reliable power
• 2-34" x 17-1/2" pad
• Two handle design for vibration operation

When working dented automotive metal panels you can never get everything out of and straight again in the metal. That means thin layers of body fillers and/or sandable primer become important for the substrate of any fine finish if you want it to look great.

I had been nursing two old line sanders (a Rodac and another probably 40 years old) along for years, and finally decided it was time for a new one about three years back. Man, what a difference! The Ingersoll Rand IRT315 Heavy Duty Air Twin Piston Straight Line Sander 2-3/4-Inch x 17-1/2-Inch Pad gave me quick and reliable starts with each squeeze of the handle trigger. I no longer had to "bump start" or work at getting a handle trigger to activate a line sander like the old ones I had been using, and I could immediately see and feel better power with less air use. Using the new Ingersoll Rand IRT315 Heavy Duty Air Twin Piston Straight Line Sander 2-3/4-Inch x 17-1/2-Inch Pad was like a dream come true, and I tossed both of my antiques in the trash.

Yes, you really need a line sander if you want your panel repairs in refinishing to be truly hidden under a perfect finish of new paint. My first use of the new Ingersoll Rand was in repairing a roof section on an old 1st generation Camaro that a large tree limb had hit. After the metal work came the layers of needed fill and the new Ingersoll Rand IRT315 Heavy Duty Air Twin Piston Straight Line Sander 2-3/4-Inch x 17-1/2-Inch Pad made much welcome shorter work of the leveling than I expected! I was done in a third of my usual time by simply using the new sander!

A drop or two of air tool oil before and after use of this tool is all you need you don't want to over oil it. There is a Phillips screw clearly labeled on the left side of the tool for oiling simple. Cleanup is really no more than a blast of compressed air to the housing.

The tool weight is just over 6 lbs., and I use a the Legacy Manufacturing HFZ3806YW2B 6' Zilla Whip Hose to help keep the tool use easier for less fatigue to me. It takes standard paper for the 2 3/4in. x 17 1/2in.. pad. The retainers for the abrasive paper are strong and hold very well. They are also easily operated. This tool also works well with either agressive or finer grit abrasive paper.

Air consumption is rated 8-9 CFM, at the recomended air pressure setting of 90 PSI. This is a professional tool that requires a 5 Hp or better air compressor for best usage. I really don't recommend trying to use it with a smaller compressor, as it will easily exceed the duty cycle of smaller air compressors in normal use of the tool. I have plenty of air for this tool as I have an industrial duty 7.5 HP 80 Gallon 1PH Horizontal 2 Stage Stationary Air Compressor in my garage.

After three years, how does my IRT315 line sander look and feel? It still looks new and it performs just as well as the first time I hooked the air to it and squeezed the trigger.

Note:

If you like this tool, you will also find this tool a great easy to work with timesaver as well National Detroit Orbital Action Sander NDT400.

Buy Ingersoll Rand IRT315 Heavy Duty Air Twin Piston Straight Line Sander - 2-3/4-Inch x 17-1/2-Inch Pad Now

This Ingersoll Rand sander is a professional quality tool and came at a very low price. A tough combination to beat. It is easy to use, durable and looks good too.

Read Best Reviews of Ingersoll Rand IRT315 Heavy Duty Air Twin Piston Straight Line Sander - 2-3/4-Inch x 17-1/2-Inch Pad Here

Bought this sander about 6 months ago to work on a car restoration project. I've used the unit for about 15-20 hours now to smooth light applications of body filler, and have been very happy with it. It is comfortable to use, and has worked flawlessly. I have a 7 hp compressor that only runs minimally while using the unit. I'd recommend this unit for anyone who has similar work to do.

Want Ingersoll Rand IRT315 Heavy Duty Air Twin Piston Straight Line Sander - 2-3/4-Inch x 17-1/2-Inch Pad Discount?

The plate of my unit arrived slightly bent, but I was able to straighten it out and carry on.

The unit is quiet and powerful. A real pleasure to use.

Save 42% Off

The IRT 315 from Ingersoll Rand is just what I expected from the quality tool maker. It runs smooth and has plenty of power to get the job done. I am sure I will be satisfied for years to come.

Ampro A1441 PTFE Seal Tape 1/2-Inch X 260-Inch

• Adds extra seal at threaded joints

Purchased this product and used it to install a shower head. It has been in my shower for more than a month now without any leaks or problems: I also recommend this product.

Buy Ampro A1441 PTFE Seal Tape 1/2-Inch X 260-Inch Now

I used this tape to install a shutoff valve. The tape does the job. Not really much else to say.

Read Best Reviews of Ampro A1441 PTFE Seal Tape 1/2-Inch X 260-Inch Here

This seal tape was perfect for sealing faucet and shower head threads.It comes with a little protective case (white shown in picture), and the tape works totally as advertised. I had no problems with it at all.

Want Ampro A1441 PTFE Seal Tape 1/2-Inch X 260-Inch Discount?

Just what I ordered....What more to say about plumbers tape?, works just as advertised....Works just fine....Works just fine....I would use this seller again...

This product worked and I will most certainly buy this again. I recommend this product to anyone. I use it to make Tiki torches out of empty wine bottles. Ampro Seal Tape, does exactly what it needs to!

- Ingersoll Rand Rotary Screw Compressor - 200 Volts, 3 Phase, 7.5 HP, 28 CFM, Model# UP6-7.5-125

• ODP electric motor
• Air-cooled aftercooler to reduce discharge air temperatures
• Full voltage motor starter (mounted and wired)
• Auto start/stop control
• Low sound/full sheet metal enclosure

This compressor is extremly quiet and smooth but I have been having problems with the belt. You can put your head right next to this thing and it just sounds like a furnace blower fan it is so quiet. BUT it has 800 hours and is on its third belt I dont know what the issue is but I am sure they will get it staightened out soon.

AAA 4344AAA 3-LED Rechargeable Flashlight

• Has 3 ultra bright LED bulbs for maximum brightness
• Initial 6 hour operating time right out of the box
• Only 60 seconds of hand cranking gives 30 minutes of operating time
• Never needs batteries
• Perfect item for the house or for the car

I got them at a rock bottom price and included them as stocking stuffers. The kids love them and they actually illuminate a good amount of light for a good amount of time.

Buy AAA 4344AAA 3-LED Rechargeable Flashlight Now

Requires an absolutely non-tiring arm to get any light. After you crank a while & finally get the light, it doesn't seem like you can keep the light unless you continue to constantly crank it. I'd rather have batteries while I can.

Heavy Duty Pressure Switch for Air Compressor 135-175 psi Four 4 Port 26 Amp

• Factory preset: 135-175 psi
• Range: 70-200 psi
• Heavy Duty: 26A
• High Quality Universal Replacement.
• Corrosion Resistant and Non Metallic Cover

I have a dewalt AC and the switch started to leak badly. I first looked for an orignal OEM replacement but it was $70+. This is close but the port orientation is 180 deg out, however this was not a problem for me as iplaned tp remove the orignal regulator assembly anyway. This will may not work (depending on you AC model) if want a direct replacement, BUT othere amazon P switches might, be carefull and check. It is also very nice to be able to adjust the cut in/out preassure ans it is very easy to do. I set my cut out at ~ 155, up from the my orignal 125. Believe it of not this makes a signifent inctease in the total cubic feet of air in your tank, which helps in those high volume needs.

Buy Heavy Duty Pressure Switch for Air Compressor 135-175 psi Four 4 Port 26 Amp Now

The one I recieved was only rated for 16 amps, won't work with my 5 HP compressor. It does work for a 2 HP.

Read Best Reviews of Heavy Duty Pressure Switch for Air Compressor 135-175 psi Four 4 Port 26 Amp Here

Carbon copy of the old pressure switch. Shipped, received in three days. Saved $35.00 over local sources. I would do repete business with this company without a secound thought.

LT5000D Lotos LT5000D 50A Air Inverter Plasma Cutter Dual Voltage 110/220VAC 1/2" clean Cut

• Automatic Dual Voltage / Dual Frequency (110/220V 50/60Hz)
• TOSHIBA Transistors (MOSFET)
• PAPST Advanced German Cooling System
• Max Severance Thickness: 3/4"
• Max Cut Thickness: 1/2"

I ordered this little gem after ordering another one from another company that turned out to be lemon, but not this one. This light weight cutter is only light to carry but cuts like a big unit. I watched a youtube video first before purchasing it. The vid shows a guy cutting 3/4 plate with it so I had to try it myself, guess what?!? Mine seemed to cut faster than the one in the vid. An easy to use, no fuss, clean cutting and huge bang for your buck tool. I suggest it to pros and bumblers too. Very nice to take to job site. As small as a shoe box on its side. I got it sent to me standard shipment and still it arrived two days from order date, TWO DAYS! So much better and cheaper than gas cutting. This is the one folks! I was also impressed that the company called me to make sure I was happy with it, outstanding! I will buy from these guys again. Kris

Buy LT5000D Lotos LT5000D 50A Air Inverter Plasma Cutter Dual Voltage 110/220VAC 1/2" clean Cut Now

Considering the average price of plasma cutters I took a leap of faith by purchasing one of the lower priced cutters. I was not disappointed. Ordered from the Lotus store front before it had any seller rating, and was pleasantly suprised at the prompt delivery.

Pro's: Great bang for the buck.

Pretty simple to operate==>watch online video.

Good cord lengths.

Just plain cool to operate.

Con's

As fore mentioned, the lack of plug should have been better noted.

The user manual is severly lacking as far as cutting and reccomended voltages.

The manual tells you on one page to touch metal with tip and then two pages later it says to maintian a 1mm distance?

Tip's

Cleaning your work is really important the + & must have good contact. The current spikes generated by the increased impedance of bad contacts is a good way blow 15amp power strips.

Start Thin and work your way up.

Wear The Right Clothing! molten metal spraying out at 66psi can cause early male splattered baldness.

It does say operators should be certified to operate the equipment, wonder if that means something.

Read Best Reviews of LT5000D Lotos LT5000D 50A Air Inverter Plasma Cutter Dual Voltage 110/220VAC 1/2" clean Cut Here

Ok, I bought this because I like to tinker and do a little hobby welding. It came fast as usual from Amazon, pretty easy to hook up, you will need to buy the plug for which ever you decide to run, I used 220volt. Made a few practice cuts and worked like a charm, cut right through 3/16" steel plate and made quick work of the 1/8" diamond plate I was testing it on. I didn't get back to it for a while and got started on a project, made a few cuts then it just quit working...not sure what happened but it happens, I checked online and found that I was past the return time for amazon, I sent some e-mails and was quickly contacted by Lotos. They sent a link to some videos and trouble shooting tips, unfortunately that didn't fix it. Lotos told me to send it back and they would replace it, in fact they had shipped it out to me as soon as I put it in the box, they didn't even wait for it to arrive at there facility, just sent the new one. For the price you can't beat it, and when the company backs there product like that what could you possibly have to lose?

Want LT5000D Lotos LT5000D 50A Air Inverter Plasma Cutter Dual Voltage 110/220VAC 1/2" clean Cut Discount?

I ordered this for my husband for his birthday. His intended purpose was to do automotive restoration projects as well as some art projects. We were a bit concerned with ordering because of the low price relative to similar looking machines from various other merchants. When the order arrived, we were pleasantly surprised. It was packaged well and the instructions were straightforward and clear. The visible aspects of the case and controls appear well made.

The machine comes without a plug and you can wire it for 110 or 220. His shop didn't have 220 wired so he put on a 110 plug. It worked quite well for light duty work on aluminum and sheet steel. When he moved on to some heavier gauge (3/16 and 1/4 inch mild steel) the shop 110 fuse would blow at the required power settings. He then wired the shop panel for a 220 outlet and put the appropriate plug on the cutter. It then worked perfectly for the heavy gauge projects. If you are intending to do light duty work, 110 is convenient... if you want to cut heavier material, go for 220.

I recommend this machine to anyone wishing to get started in plasma cutting. The duty cycle for cutting is certainly plenty for any projects we have in mind. His last project was to restore his late grandfathers large welding table that had been cut in half to make two smaller ones. We are quite happy with this purchase!

p.s. my husband helped with the details of this review :-)

Save 30% Off

What a GREAT machine. Since purchasing my Lotos LT5000D plasma cutter earlier this Spring, I have been using it extensively to cut the sheet steel for lawn art, cut the rebar for window well grates, and the demolition of various steel structures. It has worked flawlessly and with consistently good results. The unit is very easy to set up and operate. After connecting the air pressure regulator to the back of the unit and the power plug to the input wires the unit is ready to go. Simply supply compressed air at 70 psi (the unit requires about 3-4 cfm at 70 psi), the work grounding wire, and the plasma torch and you're ready to start cutting. The torch cable is about 10 feet long so there is no problem being able to move around the work area. I have found that the unit works much better on 220V but I have used it on a 30A 110v circuit with good results on 12 gauge steel. For anything thicker than that one should connect the cutter to a 220v circuit.

Cutting 12 gauge steel (about 0.1 inches thick) requires a torch current of 30 amps for which the unit has a 100% duty cycle so one can cut continuously. To cut 1/2 inch material requires 50 amps but the cut is still fairly clean. I have used the unit to cut 3/4 inch steel, but that is the upper limit of what this unit can do (Lotos states an upper limit of 1/2 inch so I was pushing the unit to do the 3/4 inch thick steel). I have used it to cut 1 inch rebar by doing a partial cut, rotating the rebar and continuing the cut.

Most of my work is with mild steel but I have used the plasma cutter to cut aluminum, stainless steel, and copper. The stainless steel cuts like mild steel (maybe even better due to its lower thermal conductivity) whereas the aluminum and copper are harder to cut. I have not experimented with various thicknesses of aluminum but I would guess the upper thickness limit is about 1/4 to 3/8 of an inch.

The unit is very portable and can be easily transported to other locations provided that an air supply is also available as well as a sufficient electrical service.

I have recommended this unit to other who have purchased it and are equally pleased with its performance.

A very nice plasma cutter.

Friedrich SS08M10

Friedrich SS08M10 -7900 BTU window air conditioner

This is my second Kuhl. I purchased the original one from M&M Appliances in Washington, DC, but took it back because it was damaged compressor ripped from the mounts and refrigerant lines bent and the backup battery was dead on arrival. Second unit seems to be in much better condition. It was not damaged and the backup battery is not dead. Friedrich also mailed me a new backup battery (see their website for the form to fill out for a free battery).

Installation was a bit time consuming and required more tools than you'd expect for a window a/c install. The hardware that comes with the unit is excellent. It is sturdy and well built. Installation is definitely intended to be semi-permanent. I will not be removing this unit every winter like I have with previous window units.

Unit cools very well and is very quiet when compared to bargain brands at many stores. Discharge air temperature with R410a seems to be lower than most previous air conditioners that use R22. Depending on temperature and humidity in the room, the unit will sometimes blow visible fog from the vents.

This air conditioner is very well built. Sound dampening could have been increased the unit makes a bit more noise than I'd like for the premium price tag. Friedrich should consider insulating the compressor in order to keep noise down. Compressor makes an oscillating sound at a frequency of about 2 3 hertz. Fan noise is minimal, which I attribute to the large vent design. The most irritating sound is the water splashing on the condenser fan. This problem could be solved by more sound insulation or by a condensate drain (although I understand that the condensate splashing on the condenser increases efficiency). Still -VERY QUIET when compared to most alternatives.

All features work well except for the auto fan mode (energy saver), which cycles the fan too frequently to "test the air temperature." I leave it set for continuous mode, which I prefer anyway. I do have a gripe about the remote control it doesn't sync with the unit's control panel, so if you make a change on the unit and then go to the remote, the remote still has its previous settings. Would be nice if the remote was RF instead of IR so that it didn't have to be pointed at the unit and it could auto-sync whenever settings are changed at the unit.

If you buy one of these, definitely read the instructions. Some parts of the install are not intuitive, and there are many features that you'll want to familiarize yourself with.

Some people have complained that the unit does not display the accurate temperature. This can be adjusted under the *temperature offset (TO)* section of the menu, along with a number of other settings.

I hope to get many years of trouble free use out of this unit.

PROS:

Sleek design with optional front cover colors

7 day scheduler

Fresh air & exhaust air control

Digital display

5 temperature sensors to monitor unit performance and temperature (Supply Temp, Return Temp (room temp), Outside Temp, Evap Coil Temp, Cond Coil Temp)

Remote Control with digital display

Very quiet

Well built

Made in the USA

Good warranty

Excellent air filter

Great customer service

11.7 SEER, great efficiency for a window unit

CONS:

Long install time (2 3 hours)

Large overall size

Damaged during shipping, glad I bought from a store instead of online!

Expensive (I hope I end up getting what I paid for)

I just have no idea why this A/C costs $800. Rich (read pretentious) look apart I haven't found a single advantage over an A/C with the comparable output you can pick up in a home improvement store for $150.

I was looking for a single most important for me function a quiet operation and I was willing to pay 6-X price for it. Good thing I decided to test it before putting in into the window. When running "fan only", it makes reasonable noise, not much quieter than a "regular" cheap A/C. The disappointing part there is only 3 fan speeds, no variable speed and/or super-quiet mode.

But when I switched it in cooling mode and the compressor kicked in, I literally jumped first the loud click and then the droning noise, so loud I thought I dropped a screw driver into the fan. After a few second the sound went down a little but it still was way over the acceptable level, and definitely louder than a cheap A/C makes. I thought the unit was defective, the dealer sent a technician, who told me that's the normal operational sound. Now I just hope the dealer won't give me a hard time when I return the A/C.

So for the price of 6 regular A/Cs you will have:

bulky heavy unit, requiring quite laborious installation process

lack of important features like variable fan speed and super quiet night mode

bunch of bells and whistles you most likely won't care about, like 7 days programming and external thermostat connector

a lot of noise

very nice looking front panel and ipod-styled remote.

You decide, but I'm returning mine.

Buy Friedrich SS08M10 Now

The compressor makes a loud throbbing noise which makes it too noisy for a bedroom. The unit is also heavy & bulky, which made installation difficult. Other than that it cools well, but so do a lot of less expensive, smaller, equally noisy a/c's.

Read Best Reviews of Friedrich SS08M10 Here

DuroMax XP652WP 2-Inch Intake 7 HP OHV 4-Cycle 158-Gallon-Per-Minute Gas-Powered Portable Water Pump

this is a very reliable pump, i purchased this one online and was very appreciative of its performance, i have used this pump sometimes running it a week at a time, it survived alot of elements, in its two years,, but just startin have a lil trouble, i bought a second identical one and for its price,, it was well worth the purchase ,, i would recommend this to anyone needin a good cheap running pump,, and at this time just purchasin a third one to replace the one giving me trouble, hope this helps in ya decision,

Well you do get what you pay for THATS for sure with this pump.Worked for 1 day and would not start after that 1 day.I paid a someone to look at and oooooooooooooooo boy he said something I would not repet other then get your money back well I'm still trying to get my money back plus my shipping of $150.00 (STAY A WAY FROM THIS PUMP)AND ANYTHING Blastwholesale sells.Ordered 3/2010 its now 10/17/2010

Al wcb

Buy DuroMax XP652WP 2-Inch Intake 7 HP OHV 4-Cycle 158-Gallon-Per-Minute Gas-Powered Portable Water Pump Now

Cheap Chinese knock-off of Honda engine. Plastic fittings had to be replaced, hose connections poorly designed, requiring additional hardware to replace flimsy plastic stuff that breaks. Cage obstructs access to air cleaner/carb. Unreliable starting.

Read Best Reviews of DuroMax XP652WP 2-Inch Intake 7 HP OHV 4-Cycle 158-Gallon-Per-Minute Gas-Powered Portable Water Pump Here

We haul water for house water.

it work real good . an it starts real easy, runs good an pump a lots of water in a shot time.

we haul 300 gal. on a trailer at a time, wer going to get 1600 gal. tank for trailer in the future.

Want DuroMax XP652WP 2-Inch Intake 7 HP OHV 4-Cycle 158-Gallon-Per-Minute Gas-Powered Portable Water Pump Discount?

Arrived on time in good shape. Pump still starts everytime with one pull after about 100 working hours. Great buy!

Save 4% Off

Hitachi 19210B Air Compressor Synthetic Oil 8oz SAE 5W50

• Synthetic Oil- SAE 5W50

If you are interested in 5W50 do not buy this product. They will send you Hitachi 19210 which is 10W30. This oil has totally different parameters then 5W50. I called them couple of weeks ago letting them know about the mix-up and they told me this is the only oil they have and still keep the same description of the product. I guess the company has an overstock of 10W30 and just wants to sell it. They do not care that it can damage your compressor.

One good thing about it is that they did not mind accepting the product back. Just remember to request the return lable for the shipment. Money for the product was refunded, but the cost of initial shipment was not (and in my case it was almost $10). It was them who sent the wrong product, so they should refound my entire costs, not only for the product.

Buy Hitachi 19210B Air Compressor Synthetic Oil 8oz SAE 5W50 Now

I am writing this review in effort to clarify what the difference is between Hitachi 19210 compressor oil verses Hitachi 19210B compressor oil. The short answer is they are both one of a kind, 5W-50 synthetic compressor oil. Hitachi added the "B at the end designating Bulk.

For those who are interested in the long version, read on. I ordered a 12 pack of Hitachi 19210B compressor oil through Amazon and received a 12 pack of Hitachi 19210 compressor oil as labeled on the bottles.

I called Hitachi's 1-800-706-7337 (USA Power Tool) number that Friday evening and asked the rep to please tell me what is the difference between Hitachi's 19210 and 19210B versions of this compressor oil is.

The response was the 19210 has been discontinued and replaced by the 19210B version. The rep had no further information spec wise and suggested I speak with Hitachi's Tech Support team but unfortunately they left for the evening and would not be back until next Monday.

That night after reading the two reviews, I too had the same concerns expressed in both of the reviews, is this a 10W-30 oil or seeing the 19210 has been discontinued, how old is the oil I received? I did not want to risk using this oil in three Hitachi compressors I own.

Convinced that there is a difference, I contacted Amazon that night and explained my issue. The Amazon rep was very polite, sympathetic and helpful. My original order was reordered with the expectation that I will receive 12 bottles labeled 19210B. I receive shipment today and on the sealed box there was a label stating "Hitachi 19210B 8 ounce synthetic compressor oil 12 bottles". The box was opened and all 12 bottles are labeled 19210.

I called Hitachi and asked to speak with a Tech Support rep. I asked the Tech Support rep what is the difference between 19210 and 19210B. The answer was there is no difference. Hitachi changed the model number by adding a "B" to indicate bulk. The silk screen label on the bottle was never changed and will read 19210 and further stated that this compressor oil is synthetic 5W-50 compressor oil.

Read Best Reviews of Hitachi 19210B Air Compressor Synthetic Oil 8oz SAE 5W50 Here

i bought 2 tubes og this and found it its false advertizing its not the B model its the really old standard number.the viscosity is probably all broken down by now and will burn out my compressor.dont trust this guy i think it was LLc enterprises or similar.buy from ebay at least i get protection from these bums that selll junk but not here.