Kraft Tool PC501 Texture Gun with Hopper

• Texture gun and large hopper
• Ideal for spraying walls and ceilings, fireproofing, stucco, decking, and waterproofing
• Two sizes of air tips 1/8-inch to 3/32-inch
• Built-in angle feature
• 1.5 gallons; 16 by14 by 11 inches; manufacturer's defect warranty

Internal parts made probably out of US. No a good quality control certification. The trigger broke the frist time I used. I do not recommended it.

Buy Kraft Tool PC501 Texture Gun with Hopper Now

I used the tool for applying knockdown texture to new and exisiting walls. The tool is well made and easy to use. For a first timer at texture I was pleasantly suprised. The instructions could be a little more explicit. I viewed a video on UTube that helped a lot and filled the gaps in the instructions. I would recommend this tool.

Camco 36143 RV Blow Out Plug with Brass Quick Connect

• Aids in removal of water from water lines
• Quick connect attaches to air compressor quick connect hose
• Plug screws into RV's city water inlet
• Patented
• Completely clear your water lines

Assuming the RV is level and the water pump is off and has been either cleaned out of water, or RV antifreeze has been added already. Simply screw this blow-out into the outside "community water port" (the port has an internal pressure valve that should be relieved of its pressure by opening a faucet and pushing on the plastic valve behind the hose seal screen (like on the female end of a hose) and attach a compressor (max 25 lbs pressure) AFTER opening a sink faucet first.

Turn on compressor AFTER opening a cold sink faucet, then open the hot side, close cold side, go to second sink, open cold, close hot on first sink, on second sink open hot and close cold (do all sinks blowing out water from each hot and cold line, not developing pressure always keep a side open) turn on the inside shower cold side, turn off sink hot side, back to shower open hot, close cold, flush toilet and keep open until water is out and mainly air comes out, same if you have a wand then close them, leave shower on/open and go to the outside shower and open cold, go back to inside shower and close hot, then go back outside and turn hot on then cold off. The key is to keep air pressure flowing through one faucet all the time and to air-out each and every faucet or place where water may freeze, and not develope pressure in the lines that could blow a seal and cause a future leak. Turn off the compressor and be sure all faucets are closed. Add RV antifreeze to all P-traps and some into gray and black water tanks. Maybe a total of 4 gallons will be used, so have 5 handy.

You can Google-search for free RV-winterizing instructions on the internet, buy a thorough RV winterizing book or e-book on Amazon, or check with your RV dealer. The internet and book has info on other things to winterize (batteries,hinges, etc., the RV place may have classes, and simplified devices such as a pump bypass kit, and RV Antifreeze, or check with K-Mart, Home Depot, Shopko, Target, Sears, Hardware stores, etc. Most any store, including Amazon, has RV Antifreeze in the fall which IS different from car antifreeze, ans a great selection of RV Parts; look for -50 degree formula, pink RV antifreeze.

This air-hose blow-out and the tire-stem type work the same, I have one of each, just depends on the compressor line-end you use. Both types are highly recommend and I recommend Amazon ans Prime. DO NOT ADD RV ANTIFREEZE TO THE HEATER OR EMPTY FRESH WATER TANK (waste of liquid, money, time, and it's hard to dilute and flush out in the spring); just be sure they are drained as best you can, and closed. Best to buy a pump diverter kit as it makes the process simple and saves you a lot of antifreeze. Antifreeze should be in all P-traps, shower drain, and some in both septic tanks; let a little antifreeze drain through the septic gate-valves to protect them from pockets of water. Hope this helps. What you miss can mess up RV time next year.

Buy Camco 36143 RV Blow Out Plug with Brass Quick Connect Now

I think this product speaks for itself. It's the nearly the same price as the plastic blow out plugs with two major advantages. 1. It's Brass. It's going to last for a long time and your not going to break it. Your dog isn't going to chew it up either. 2. Your air hose attaches directly to it.

Read Best Reviews of Camco 36143 RV Blow Out Plug with Brass Quick Connect Here

This is great for blowing out hose type garden sprinkler systems. Nice for blowing out hoses before winter storage. I did need to drill out the orifice larger to get more air flow..no big deal though

Want Camco 36143 RV Blow Out Plug with Brass Quick Connect Discount?

We have had campers since the 70's and winterizing each year was always an event. I have used adapters that you had you had to hold in place and even made some of my own creations. This is a soild brass adapter that screws on to the hose connection on the camper. It is not one of those plastic use once and throw away plastic adapters. It doesn't leak and lets your compressor hose lock on to it letting you go into the camper and open up each faucet until there is only air coming out. I think this brass adapter is well worth the money.

Save 18% Off

I bought this to blow out my sprinkler system for winter. I needed an appliance water hose to connect it to my spigot (female-female) since RV connections are reversed. The blow hole through the center is a little small and per advice of another reviewer I drilled it out. Took about 2 minutes. It may have worked fine that way for an RV, but I need to push 80 PSI to my sprinklers. I'm very happy with it. The threads are nice and sharp and it's one solid piece of metal.

Heavy Duty Pressure Switch for Air Compressor 135-175 psi Four 4 Port 26 Amp

• Factory preset: 135-175 psi
• Range: 70-200 psi
• Heavy Duty: 26A
• High Quality Universal Replacement.
• Corrosion Resistant and Non Metallic Cover

I have a dewalt AC and the switch started to leak badly. I first looked for an orignal OEM replacement but it was $70+. This is close but the port orientation is 180 deg out, however this was not a problem for me as iplaned tp remove the orignal regulator assembly anyway. This will may not work (depending on you AC model) if want a direct replacement, BUT othere amazon P switches might, be carefull and check. It is also very nice to be able to adjust the cut in/out preassure ans it is very easy to do. I set my cut out at ~ 155, up from the my orignal 125. Believe it of not this makes a signifent inctease in the total cubic feet of air in your tank, which helps in those high volume needs.

Buy Heavy Duty Pressure Switch for Air Compressor 135-175 psi Four 4 Port 26 Amp Now

The one I recieved was only rated for 16 amps, won't work with my 5 HP compressor. It does work for a 2 HP.

Read Best Reviews of Heavy Duty Pressure Switch for Air Compressor 135-175 psi Four 4 Port 26 Amp Here

Carbon copy of the old pressure switch. Shipped, received in three days. Saved $35.00 over local sources. I would do repete business with this company without a secound thought.

Engel MR040 Portable AC/DC 12 Volt fridge-freezer (40qt)

• Power consumption: 0.7 - 2.5 Amps
• Volume: 40 qt. - Equivalent 58 cans (12 Fl.oz)
• Weight: 48 lbs.
• Freezing Ability: From 40°F to below 0°F
• Warranty: 2 years

I'm an OTR trucker & this Fridge was tailor made for us guys. I have estimated I have saved many times the cost of this fridge over the 5 years I have owned it. Along with a small microwaveGE JES735WJ .7 Cu. Ft. Capacity Countertop Microwave Oven& a 12V/110 inverterCobra CPI1550 Dual Outlet AC/DC Power InverterI'm not a slave to overpriced truckstops. I can carry along a weeks supply of groceries(Leftovers, TV dinners, Lunch meats & cheeses etc.) along with all the beverages I need. Restocking is a matter of stopping at any large supermarket.Don't let the large size intimidate you as you rareley have to take this out of your vehicle......just take the removable wire basket(included) out, load & put back in the cooler & your good to go. The fridge fully loaded weighs upwards of 100lbs with 50 of that for the groceries. When I get ready to leave I just load the basket, take it to the truck & drop it in.

Unlike the cheap Thermo-electrics the Engels has a compressor & cools or freezes to whatever temp you set it., one or the other but not both, either a fridge or freezer & its not dependant on ambient temp.

A side benefit; unlike built in fridges this one goes with you whether your switching trucks or going on vacation to the lake(works on 110 as well as 12V so you have a spare fridge/freezer at the cabin)If you plan on an extended stay on the lake this will work in you boat as long as you have a 12V plug in.

All in all a great little cooler.Very rugged & very reliable

Pros

1.dependable

2.quiet

3.energy efficient

4.portability

5.built like a tank,steel housing

Cons

1.cost

2.bulky

If this one ever quits I will buy another.

Buy Engel MR040 Portable AC/DC 12 Volt fridge-freezer (40qt) Now

This freezer is based on the Sawafuji "swing" compressor. Unlike the fairly similar and far less costly EdgeStar FP430 which uses a Danfoss compressor, the Engel MT45F is specifically designed to be operated in a moving vehicle, and can be run while at an angle of up to 30 degrees. It pulls a maximum of 2.5 paltry amps at 12 volts DC (the Edgestar draws 2.75 amps max, but can get food a little colder). It has a steel exterior, while the similar but less expensive ARB Fridge Freezer, which also uses the swing compressor, has a tough plastic housing, which might be a better choice for boaters.

The Engel is built like a tank, and comes with a 2-year factory warranty. I've had mine running while driving over thousands of miles of rutted dirt and gravel roads, and it works as well as the day it was new.

My biggest beefs with the Engel are: the price, which is close to twice that of the comparable Edgestar and more than the ARB; the storage capacity, which is pretty small; and the primitive controls--no temperature readout, and only a single dial marked 1 5. A more minor gripe is that the compressor hum, while not terribly loud, does seem to carry--you'll know when the Engel is running. Also, it is heavy. Those big steel handles are there for a reason (they also make good tie-down points).

Read Best Reviews of Engel MR040 Portable AC/DC 12 Volt fridge-freezer (40qt) Here

I've been an avid camper for more than three decades and got into off-road exploring about 18 months ago with the purchase of a new truck. We often spend two and three nights and days out in the desert of Southern California trekking about. In the summer we have problems maintaining our food at safe chill levels and our drinks at the preferred temperature.

I have an electric cooler which does only a fair to poor job of keeping the internal temperature 20-30 degrees cooler than the 100 degree external temperature. Food will spoil quickly at these temperatures. I've tried three different coolers of increasingly larger sizes stocked with more and more ice. I ended up with two coolers stuff at about 50% ice and 50% food or drink.

With the outside temperature of 68 degrees I read the following temperatures inside the empty Engel 45:

1 = 39 degrees

2 = 25 degrees

3 = 20 degrees

4 = 14 degrees

5 = 1.9 degrees

The basket pulls out so that you can fill it in the kitchen and haul the food out to the waiting freezer. This helps make moving the already freezer easier.

Want Engel MR040 Portable AC/DC 12 Volt fridge-freezer (40qt) Discount?

I do a lot of off-road camping (research). I used a Dometic absorption cooled refrigerator for the past few years, which ran on 110 / 12VDC / Propane. The challenge I've had with the Dometic is it couldn't keep temperature in the desert heat. Other problems were the Dometic had to be out of the wind else the flame blew out and absorption systems need to be absolutely level something difficult to achieve when off-road. After a 10 day trip where some of the food spoiled in the Dometic despite my best efforts, I made the decision to look for a more capable refrigerator. After considerable research, I settled on the Engle MT45.

What a difference! The MT45 easily maintains temperature in the desert heat and will quickly chill water bottles and drinks added in something the Dometic couldn't do. It is surprisingly efficient. While the unit is rated at 2.5 amps, that's it's maximum draw at start-up when cooling down. My experience is that it draws on average around 1.1 amps (cycling on and off) when it is up to temperature. My vehicle has an auxiliary battery which is recharged by a 110 W solar panel when on location. With the Engle drawing approximately 30 W maximum, the setup is sufficient to keep the MT45 running indefinitely without the need to start the vehicle to recharge the AUX battery. With a 105 AH AGM battery, I can run the Engle for two days without recharging the battery, figuring a 50% max discharge of the battery and no sun to supply the solar panel. That's pretty good efficiency. The MT45 can operate at an angle of up to 30 deg. No more having to shove shims and rocks under the fridge to get it level like I had to do with the Dometic.

While the MT45 doesn't have a temperature read out I found that a wireless thermometer works just fine and is a small price to pay to be able to see the internal temperature up front in the drivers seat (or trailer). Keeping the MT45 dial at a little above 1.5, the fridge maintains temperature at 38 deg. F. The dial ranges from zero to 5. At 4 or 5 the MT45 can keep items frozen solid.

I really like the basket arrangement. It makes it easy to see and get at items. It also allows me to carry the refrigerator to the Land Rover empty then carry the food and drop it into the Fridge, lessening the weight I need to carry. The old Dometic had to be filled then carried, often very heavy to lift. So while some complain about the weight of the MT45, remember that you don't have to lift it with the food in it. Another benefit that I really like is I can pack the food in the Engle basket and store it in my home refrigerator to keep it cool until I'm ready to transfer the food to the MT45 before heading out.

The MT45 is built tough with solid steel construction, which adds to the weight. I'd rather have a durable unit than one that can't take the abuse. I'm miles from civilization and I need reliability.

I read a few comments about the vibration. While I don't discount that the individuals may have gotten a particularly noisy unit, a hum is characteristic of the Engle "swing" motor compressor. The compressor has only one moving part, making it far more reliable and efficient than other designs. My MT45 does have a hum when running but it doesn't bother me. It's really not all that noticeable. It is certainly louder than my previous Dometic, which made no noise at all but, after all, it is a compressor design, which is far more capable than the absorption design of my former Dometic. It's going to make some noise. I'm happy to have cold drinks and food that isn't spoiled. That's the whole point in my estimation.

Overall, I'm very pleased with the Engle MT45. I wish I had purchased it years ago and avoided all of the challenges I've faced trying to keep perishables from perishing when out at research locations in the desert Southwest.

Right out of the box it had a constant hum whenever switched on. It also had a lot of vibration. Even when placed on a pad or a carpeted surface, it would still make a constant sound. Could be heard when I had it in the tailgate of my SUV and I was driving!

For several weeks I've been 'working' with Engel on resolving this. They said it's not uncommon. They believe it's caused by something in the compressor mounting shifting during transit. They first had me 'bang' it on each of it's sides while it was running. Then they had me open it up!...and directly hit the compressor with a rubber mallet, again trying it on each side (orientation) and with it running.

Nothing has made a difference. Each time I've spoken to them I've asked for return information so I can send it to them to be replaced or repaired (though I'd prefer a brand new unit just replaced). I think they're being cheap as they insist each time that they have something new to try that'll be easy. All I've accomplished is getting scuff marks on the outside of my unit as well as paint chipped on the compressor housing.

This is not a $20 item! And yet they treat their customers as it was. I would not recommend anyone to buy one of these. This is not a unique occurrence. I know this because Engel told me this! Also, if it was a rare occurrence, they wouldn't hesitate to have me ship it to them for repair. They obviously have a problem and are trying to resolve it as cheaply as they can and/or get people to give up on their grievance.

Rolair JC10 Super Quiet 1HP Oil Less 2.5 Gallon Air Compressor

• One of the quietest and most reliable air compressors on the market today
• 2.5 gallon tanks capacity means you can work longer with less waiting for the compressor to catch up
• Oil-less design reduces maintenance and downtime
• Compact and lightweight design makes it easy to transport to and from the job site
• Protective roll cage helps prevent possible damage when transporting

This is a great small compressor for interior trim work. Exceptionally quiet. So quiet if you are working in a house with a radio on and the compressor is in a different room you won't hear it. This compressor is slightly different than other small compressor I have used. It has a 1Hp motor and plenty of power. It has a high volume direct drive pump,producing about 2CFM @ 90psi ( sorry I do not have the exact specs). One motor and 2 compressor heads. It weighs about 38 pounds, light enough to carry easily, but slightly heaver than some of the other small airless compressors on the market. Rolair compressors have always been a top of the line unit, you can see they used top quality components, but you can see the bare bones approach to the design to keep the cost down. So many of the other compressors on the market use inferior components to keep the cost down, and it shows in the operation.

It has a typical cartridge air filter, very good quality gage's that really work, A high quality type M universal hose coupler, and good quality materials, and components throughout. It obviously is not a continuous run compressor, like most oil less units, but I was not able to find a duty cycle for this unit. It still has plenty of air to run 2 trim guns, or to do other small jobs. My complaints are minor. The hand grip could be improved, it would be just as easy to carry this with out any grip on it. The anti vibration feet on my unit were not installed square to the frame, so it dose not sit as well as it should. The electric cord has no place to wind up, if it had a cord snap on the plug at least you could wrap it around the frame and snap it to itself. I would also like to see 2 hose connectors in stead of one. All in all this is a top quality, provisional grade, compressor at a very reasonable price.

Buy Rolair JC10 Super Quiet 1HP Oil Less 2.5 Gallon Air Compressor Now

Excellent small compressor. More quiet than any other I have seen; usable in an occupied room with few complaints. Very rapid recovery rate, and very little vibration.

Read Best Reviews of Rolair JC10 Super Quiet 1HP Oil Less 2.5 Gallon Air Compressor Here

This compressor ROCKS!!! It's not made to run all day or run a lot of guns. But if you do trim or cabinets, this is perfect. It has enough power to run a 18ga and 15ga nailer and drive it into 2 inch thick oak. It will not disturb others in the work environment. I used it to install cabinets in a open office environment and no complaints of too much noise or oil leaking on the carpet. It really dose what it was intended for. I rate 5 stars!! Rolair knocked it out of the park on this one!! If you want a light weight and really quite compressor.this is the one!! Made in the USA!!

Want Rolair JC10 Super Quiet 1HP Oil Less 2.5 Gallon Air Compressor Discount?

The other reviewers were spot on, thanks folks!

I was worried this might be a bit overhyped, but holy moly! This thing is quiet! It came on with a purr, aired up in less than a minute and I sunk a good 10 or so finish nails before it cycled on again. It refills in about 8-10 seconds. Very consistent. Wonderful.

My last portable compressor was one of the cheaper pancakes. It did the job, sort of, but I hated that thing! Loud doesn't begin to describe that banshee! Imagine someone shaking a coffee can half full of bolts in your ear for 10 minutes. I'll make concessions for power, but that thing didn't offer any of that either. For all the noise it made, it couldn't keep up with this Rolair, I'll tell you that. I finally burned it up forcing it to keep up on a roofing job. Went Office Space on it. Good riddance. Worst money I've ever spent on a compressor.

This little compressor only cost $50 more than that howler monkey, so this little Rolair is a dream for me. Like complete opposites.

Not sure yet how it will stand up, but so far it has kept up with every nailer I use. From the finish nailers down, it keeps up easily. With the larger nailers, like my roofing and framing nailers, it will keep up at a slower pace, but I wouldn't put a continous duty cycle like that on one of these. For small jobs, no problem though, and the lightweight pleasant nature of it makes it a joy to use. It is no heavier than a kettlebell, so I can flip it over a shoulder and walk up a ladder with it. It is squarely framed and sits squat, so it is stable in the back of my truck or I can toss it on a seat for transport. I like to keep him on the seat so I can pet him while I'm driving. He likes that. Just kidding, but seriously, I'm loving this little thing. It's like R2D2.

The comments others have made about the viewing angle of the guages I would agree with. It sits so low that viewing the guages takes a tilt to accomplish and when you're swapping guns often that slows you down. I don't care, I'll relocate the guages. I love this little guy.

5 stars and a rebel yell from me!

Save 39% Off

Actually got this for 189.00 at tools plus.At the time amazon was 200. It is whisper quiet and easy to haul around. I looked extensively at the Bostitch 1512 and the Mac 700 which are also excellent choices. Thing that sold me on this was Dave Reinhold's video for tool nut on you tube.It does everything I need it to do from light framing to extensive trim work,could not be happier.

Black & Decker ASI300 Air Station Inflator - Electric Air Compressor

• Inflates lawnmower, bike, and vehicle tires, sports balls, and other items quickly and easily
• Space-saving, portable design
• EZ air dial for instant shut-off when correct air pressure has been reached
• Weighs 6.1 pounds; 2-year warranty
• Includes standard tire nozzle, needle inflator, and extension nozzle

I am pleased with this inflator so far. (I hedge a bit, given the reviews stating that the device has failed for other users. But that's what the warranty is for.) It is easy to use, effective, and convenient with its storage compartment for power cords and inflation hose. I especially like the automatic cutoff feature; I can turn it on and let it do its thing while I'm doing something else. I run my automobile tires at higher pressures than most (60 PSI), and it had no trouble with those. It takes a couple of minutes, of course, but that's to be expected -this is not a mechanic's air compressor, and I don't expect that level of performance. I haven't tried them on my higher pressure (90 PSI) bicycle tires yet.

Negatives that other reviewers have mentioned and my comments:

* Gauge readability: Yes, it's a little hard to discern small PSI increments on the gauge. But I never rely totally on any pump's or inflator's built-in gauge for my tires; I always verify with a good quality tire pressure gauge. The inflator's gauge and cut-off get me in the ballpark, and then I fine-tune using the tire pressure gauge. They are within 1 or 2 PSI of each other.

* AC power cord length: Not an issue. I likely would have to use an extension cord anyway. And the short power cord adds a bit to its portability -no fiddling with it or trying to store a long (and useless while traveling) power cord with the device as it sits in my trunk.

* Noise: No worse than any other inflator I've used.

* Small storage compartment for cords and hose: Not too much of a problem, though it might take a little practice to get them coiled up the right way. It's handy to have the compartment.

* Short inflation hose. No shorter than other inflators in this price range I've used. Plenty long enough to reach a valve stem at top dead center with the device on the ground next to the tire.

* Plastic connector that *might* break. I'll judge it if or when it actually breaks, not before.

* Having to cut the power switch off and then on again to run it after an automatic cutoff: Gimme a break, how big a deal is that??

Buy Black & Decker ASI300 Air Station Inflator - Electric Air Compressor Now

I have used it for about a week now. It is much better than the one I got from Walmart. The major issue I see is that the pressure gauge on this machine is rather small and it will be hard for you differentiate between 27psi versus 29psi without using an external gauge. My Toyota Camry calls for 29psi and my other car asks for 34psi front and 36psi rear. It was impossible for me to read 34 vs 36 psi on this machine's gauge.

Tip: To get the best out of this machine get a good external mechanical pressure gauge with a relief valve (you can get a decent one for under $10 at Walmart). Then set the dial on this machine to be slightly over (2-3 psi more) the pressure required (I set it to 30psi when filling my Camry which needs 29 psi). Fill the tires with air using the machine. Then use the external gauge to measure the pressure and release the air using its relief valve until the pressure is at the desired reading. Works like a charm for me.

Other than this, the machine is quite nice and with a 2 year warranty it is a good buy. Amazon's price was amongst the lowest I could find.

Read Best Reviews of Black & Decker ASI300 Air Station Inflator - Electric Air Compressor Here

Overall works pretty well.

Positives:

All hoses and wires and adaptors store inside the unit, for neatness.

built-in handle is nice

long 12V auto power cord

two-year warranty

Negatives:

When it stops automatically after inflating one item (such as a tire), it must be turned off and back on to inflate another item, or to increase pressure setting and continue filling.

the AC power cord is extremely short. Pretty much requires an extension cord.

the air hose is fairly short.

The noise it makes is quite loud, though not as loud as some I've heard.

fitting the cords and hose back into the storage compartment is not easy.

the valve adapter is plastic, not metal, and doesn't seem sturdy. It works so far, however.

Want Black & Decker ASI300 Air Station Inflator - Electric Air Compressor Discount?

Overall, I like this inflator. As is typical with about anything, it has strengths and weaknesses. The strengths:

Once set, I verified with a digital tire gauge that the built-in pressure gauge is accurate to

25g Bench Top Sandblast Sandblaster Cabinet Blast Media

I got this cabinet to avoid building my own for small glass sandblasting projects with a small compressor. Cost less than the materials would have and, while I thought the included gun would not be useful with the small compressor, was pleased to find that it worked well enough with the fine grit used to speed projects through.

1st review (after few hours of work) :

I bought this of ebay for 110$ shipped and it's wonderful. It came well packaged and contrary to other reviews mine didn't leak at all. My only problem was that my 5 gallon compressor was dropping pressure way too fast for me to do any kind of sand blast.I hyad to stop every 2 minutes to wait for pressure to built back.

If you are looking into buying one of theses and don't have money for more rugged versions get it!

2nd review (after 2 months of use):

It leaks!!!!! but easily fixable with sealer around the top window and a new bigger foam strip from hardware store for the door. I bought a ch compressor vt6275 witch is more then efficient for this kind of job. and it works great. I tried to blast 13in wheels (5"wide) in there and it was a pain, the cabinet is too shallow and its hard to blast.

I would only recommend this cabinet to anyone that wants to fix it first and use it only for work on small items (brackets, nuts, bolts etc.).

NB: i buy my sandblast media from tractor supply for very cheap (their aluminum black diamond is great.) cheaper than anything here.

Buy 25g Bench Top Sandblast Sandblaster Cabinet Blast Media Now

It is what it is a box. It leaks some but I expect and can live with that feature. The interior light worked for about 30 seconds and went out. I called the vendor and was told they would send another light; they did and it works.

Read Best Reviews of 25g Bench Top Sandblast Sandblaster Cabinet Blast Media Here

This was one of the best investments I've made it a long time! I repair electric motors for my job and 4 out of 5 times the motors are in horrible shape. I've tried everything under the sun to clean the corrosion off and while there are ways, they are not easy and very time consuming. Since the purchase of this little puppy, that is no longer the case; I can do twice as much in 1/4 the time now.

Just remember to clean filters frequently so the cabinet stays clear of dust.

Want 25g Bench Top Sandblast Sandblaster Cabinet Blast Media Discount?

Nice cabinet for the most part, a little bit cheap feeling, the light died after 1 week..But it's still getting the job done.