Tru-Flate 18-221 1/4" Female NPT Input Siphon Spray Blowgun

• Combination of a standard blowgun and the siphon spray nozzle
• Barbed siphon inlet fits 1/4 inch ID hose or tubing
• Use for spray-cleaning engines applying protective coatings etc.

This tool is well balanced with the suction attachment on the blow gun, but the suction was just too weak for the intended application. Operating at 60psi supply, the suction can barely be felt when you block the suction line with your finger. There is a tradeoff between suction and air consumption other units provide more suction at the cost of higher air consumption, so if you have a smaller size compressor this spray gun will provide longer usage time between compressor cycles.

Save 57% Off

Amflo, 112, Hose 3/8X12In. F/ Amf100 Series Tire Inflators

I AM ABLE TO DO ALL THE DOTS THAT I WANT IN DIFFERENT SIZES!! LOVE IT CAUSE IT HAS A VERY TINY TINY ONE TOO

Expectations were exceeded. Item arrived earlier than expected and the hose fit without having to make any adaptations. It is more flexible than the one it replaced, so I do not expect the outer casing to crack as the last one did.

Buy Amflo, 112, Hose 3/8X12In. F/ Amf100 Series Tire Inflators Now

Coxreels Air Hose Reel With Hose - 3/8in. x 50ft. Hose, Max. 300 PSI

• HOSE REEL
• COXREELS Performance Series Self-Retracting Air/Water Reels store hoses neatly and prevent wear and user fatigue.
• Mount on floor, wall, or ceiling.
• Pressure rating to 300 psi.

Coxreels Air Hose Reel 3/8" x 50ft. hose 300 PSI

This product is the Coxreels model P-LP-350. P: Performance series; LP: Low Pressure (300 psi); 350: 3/8" x 50' hose (included).

I've owned one of these reels since 1993, and have used it hundreds of times.

The reel works as you would expect of a high-quality product. To have the reel lock at the hose length needed; pull out what you need, and stop after one of the loud clicks. When done, pull the hose out a foot or so to release the lock, and slowly release the hose for it to automatically roll back up. Don't let go of the hose at that point, because it goes in so fast, it could hurt someone or damage something if smacked by the hose end. (The only reels on the market where it's safe to let the hose go when it's winding up, is the more expensive Coxreels EZ-Coil series; they feed the hose in, slowly.)

About 6 months ago, air started leaking in the fitting that the air compressor's hose attaches to. I sent an e-mail to Coxreels technical support and they told me which new part would eliminate the leak. I purchased, then replaced the swivel (see Customer Images), and the reel is as good as new. It's nice to know you can still get the manufacturer to provide advice on a 15-year old product.

The reel is all steel, except for the brass fittings. The base is 1/4" steel plate and is very strong. The painting has held up without any issues. The hose that comes with the reel is excellent reinforced rubber. It looks pretty much as it did 15 years ago. There are no rattles when pulling the hose out, as with some cheaper hose reels.

This is a high-quality, professional-grade hose reel. Highly recommended.

Buy Coxreels Air Hose Reel With Hose - 3/8in. x 50ft. Hose, Max. 300 PSI Now

Amazon's description and pictures are some times confusing. If you want a hose reel with hoses, make sure you read very carefully that it does come with hoses.

Read Best Reviews of Coxreels Air Hose Reel With Hose - 3/8in. x 50ft. Hose, Max. 300 PSI Here

High quality professional unit. Works very well. Mounts on wall or ceiling. Does not leak air. Strong recoil spring. High quality hose also. You will need a typical 3/8" hose to run from your air compressor to the hose reel. Hose and fittings are easily found at Home Depot etc.

Compressor Saver CSR U1 Hard Start Capacitor

This kit is great for any type compressor (scroll or reciprocating). Easy to install & will not harm compressor windings because of the lower capacitor rating (88-108uf). (If you need a Hard Start kit to try to free a stuck compressor you will need a kit with a much higher uf rating.) This kit lowered my start up amperage by 10 amps. If you are thinking of buying a 2 wire kit think twice because most of them work on a thermistor and will only work once and not again until the thermistor cools down and on a hot day that could be awhile. Since a 2 wire type operates on temperature and not on the run speed of the compressor it could stay in the circuit longer than needed or not long enough. This 5-2-1 kit removes the capacitor from the circuit when the compressor reaches a certain speed which is done by the relay sensing voltage.

I emailed the company to ask a question about the type of relay that they used & received an answer back the same day from one of their technical engineers. How refreshing it is to get a prompt response from a company these days.

You may spend a little more for this start kit but is well worth it as it should last longer than a 2 wire type and is safer for your compressor.

Last year I had the HVAC guy come out and work on my AC compressor. He used a two wire hard start kit to get my compressor going and said that I had a "tight compressor". The compressor worked for the hottest months of the year then quit again. When it quit it took the contactor and the transformer with it. I decided to take a chance on this hard start kit. I replaced the contactor, the 115 volt to 24 volt transformer and I added this 521 kit. The compressor came on and I have had nice cool AC this summer.

I did a lot of research before buying the 521 kit. I would recommend that anyone who wants to install a hard start kit avoid the two wire kits. All the reading I did indicates that over the long haul they are trash. Spend a few extra bucks and get this kit. It works great.

BTW, My unit is a 2.5 ton residential unit.

Buy Compressor Saver CSR U1 Hard Start Capacitor Now

Dose what it claims to do and I did not need to hire someone to install it. It was easy, and I am not that technical , just follow the diagrams and you can't go wrong. I love this freakin thing!!!!!!

Read Best Reviews of Compressor Saver CSR U1 Hard Start Capacitor Here

Very easy to install. Cut down on compressor start-up noise. Start-up AMP's were 40-45% less. I will be installing these on all my families AC units.

Want Compressor Saver CSR U1 Hard Start Capacitor Discount?

I installed this on a new 2.5 ton Goodman heat pump. Clear instructions, color coded, easy to install, works great!

Pro-Force FT10 10-Gallon Portable Air Tank

• 135 Max PSI
• Fully assembled, ready to use
• High quality brass manifold
• Durable welded on handle
• Equipped with air pressure gauge, air line shut-off valve, pressure relief valve, easy access fill valve, 3-Feet by 1/4-Inch air hose and air chuck

The tank arrived within the scheduled and promised time and worked as expected. I really like the larger capacity of this tank compared to the smaller one I've used for years. I immediately modified the tank to accommodate quick connect accessories so that I can use it as an inflator or duster and can even use small air tools in a pinch. Overall, this is a very well made product and I would recommend it for small 200 PSI and under project needs.

Save 24% Off

Amico Red Push Button 1 Port NC Type Air Compressor Pressure Switch

• Product Name: Air Compressor Pressure Switch; Type: 1 Port, Normally Closed(NC)
• Max. Voltage: AC 240V; Current: 15A; Pressure: 175PSI, 12 Bar; Joint Thread Dia: 11.8mm/ 0.46"
• Inlet Thread Dia: 6mm/ 0.23"; Total Size: 12.5 x 8 x 5cm/ 4.9" x 3.1" x 2"(L*W*T)
• Button Diameter: 2cm/ 0.8"; Inlet Hole Dia(Each): 15mm/ 0.59"; Material: Metal, Plastic
• Main Color: Black, Red; Weight: 287g; Package Content: 1 x Air Compressor Pressure Switch

I would have tried to return but the hassle was too much, i needed a two outlet and fixed this with that "t" adapter from lowes and some teflon tape.

Works great!

Senco A209909 18-Gauge-by-1-2-Inch Electro Galvanized Variety Pack Brads

• 1,200 brads per pack
• Use for ouldings, picture-frame assembly, trim, and cabinetry building
• Fewer tool jams than competitors
• Highest withdrawal values for fasteners
• Engineered to fit competitors' tools

Yes I did. Throughout hundreds of firings so far, these nails never caused a jam. Definitely a recommended product.

Buy Senco A209909 18-Gauge-by-1-2-Inch Electro Galvanized Variety Pack Brads Now

Product is great. Reasonable price. Works well in Firestorm Cordless Nail Gun. Good to have assorted sizes on hand.

Read Best Reviews of Senco A209909 18-Gauge-by-1-2-Inch Electro Galvanized Variety Pack Brads Here

I have a Dewalt cordless 18-guage nailer that I use for quick handyman projects. I keep this assortment kit inside the tool's case. It is small, clear and has everything from small to large for every need. I refill it from one-size packs of 1000+ nails that I can't fit in the tool's case.

Want Senco A209909 18-Gauge-by-1-2-Inch Electro Galvanized Variety Pack Brads Discount?

exellent value great assortment if your like me and just have the odd jobs to do

Save $0.04 Off

I bought these nails for use with the Hitachi brad nailer I bought on Amazon at the same time. The nails came in a variety of sizes and functioned flawlessly. I did not experience any miss fires or loading problems. I don't know how much credit goes to these nails or or the great Hitachi brad nailer, but both work great together. If you need just one size, I would only order the single size pack, however this variety pack was great for my needs and included plenty of nails in each size.

DeVILBISS AIR LINE FILTER/Water/Oil Trap w/50 Foot HOSE

• Devilbiss Finishline HAR-602 AIR LINE FILTER with REGULATED CONTROL UNIT
• Plus a 50 Foot 3/8" Goodyear Rubber Air Hose

Just as described. Had to buy a few fittings to mount. Would like to have had a fluid filled pressure gauge...that's easy enough to change out. That's personal preference. Item was purchased to remove water and regulate pressure for sandblasting and painting. Performs as expected.

Buy DeVILBISS AIR LINE FILTER/Water/Oil Trap w/50 Foot HOSE Now

I recently purchased a Ingersoll Rand air compressor 19CFM at 90PSI I needed a filter. I found this one it was the right price for my budget and so far has done every thing I have asked it to do, it removes the water for my sand blaster and it works as they advertized so far great product the only thing was had to get a cupping to adapt the hose no big deal, for the first time I got tired of sandblasting before I ran out of air and my nozzle never clogged due to moisture! The only thing I would do is purchase a spare \ replacement filter just to have.